Item #: TI-TG-02B-DC12B -
If you are looking for a food safe Arduino Pump the RobotGeek Large Liquid Pump is a great solution. This pump is self priming, quiet, and can move up to 2 liters per minute. To use this for an Arduino Pump project all you need is a RobotGeek Relay and seperate power supply. The pump will work with standard aquarium tubing. The fit is a little tight, but the tubing will go on. We recommend picking up some of our food safe 3.5mm silicone tubing which fits great and goes on easier! Recommended...
Item #: RG-SMPUMP -
If you are looking for an Arduino Pump the RobotGeek small liquid and air pump is a great solution. This pump is self priming so it can be used for projects involving plant watering, suction, drainage, drink dispensing, barbots, and more. To use this for an Arduino Pump project all you need is a RobotGeek Relay and seperate power supply. The pump can operate at either 6 or 12 volts and packs a punch in a small package! Recommended Arduino Pump Tutorials: Arduino ShotBot Project Arduino Pump...
Item #: HW-WVALVE -
If you are looking for an Arduino solenoid valve the RobotGeek liquid solenoid valve is a perfect solution. Compact with mounting holes make it a great fit for DIY projects of all kinds. The Solenoid Valve is a great companion to the Large DC Liquid Pump and the Small DC Liquid Pump. When building pumping projects sometimes it is necessary to add a valve to stop either liquid back draw or unwanted flow. When using diaphram pumps if your liquid supply is higher than your pouring point, pressure...
Item #: MOT-VIBO8 -
Weighing in at just 35 grams, this RG90 Gear Motor can put put an impressive 1.2 kg/cm of torque! That makes it great for small, wheeled robots! The double-flat output shaft is 7mm in diameter and is perfect for attaching to our Gear Motor Wheel. Our gear motors come with two- 300mm wires pre-soldered onto the motor. Each wire is terminated with a 2.54mm female connector. This makes them ideal for attaching to any 2.54mm pin connector. RG90 Gear Motor Operating Voltage 6V No Load Speed 90 RPM...
Item #: PO-1084 -
These light-weight brackets (under 15 g each) are specifically designed for the Pololu 37D mm metal gearmotors, such as the 19:1 metal gearmotor 37Dx52L mm and the 19:1 metal gearmotor 37Dx52L mm with 64 CPR encoder. Each bracket features seven mounting holes for M3 or #4-size screws along each edge, giving you a variety of mounting options. A total of twelve M3 screws (six for each bracket) are included for securing the motor to the bracket. NOTE: This set contains 2 brackets and DOES NOT...
Item #: ASM-GM-WHL-SET -
This kit is a combination of two RG 90 Gear Motors and two matching Gear Motor Wheels.The variety of mounting holes on the gear motors will make them easy to mount to almost any chassis. With a weight of 18g, this set is a great choice for small robots and rovers. RG90 Gear Motor Operating Voltage 6V No Load Speed 90 RPM No Load Current 150 mA Stall Current 800 mA Output Torque 1.2 kg/cm Gear Ratio 1:120 Overall Dimensions 54x42x23mm Weight 35 grams Technical Drawing Download 3D File Download ...
Item #: ASM-GMW -
Do you need a wheel for your latest rover? Try our new Gear Motor Wheels! These wheels are made of a red acrylic, wrapped in a black rubber tire. Each 9cm diameter, 1cm thick wheel has a double-flat, 7mm in diameter hole -perfect for our RG 90 Gear Motors! Just use the included hardware to attach the wheels to the motors and your robot will be rolling in no time.
Item #: MP-EPF200 -
The Mini Turbo Fan is a Mini Badass. Sporting 73g of thrust while weighing in at only 30g it can take off if you give it full throttle. Perfect for fire fighting robots or cooling you on hot summer days. The Mini Turbo Fan comes with a heat sink and 4" cable with male ends. To extend the cable we recommend using our 2-pin F/F jumper cable. *The fan edges may rub against the duct walls when you first run it. This is okay. The blades will actually trim themselves down. That is how badass this...
Item #: KIT-MTR-36-06-180 -
We searched high and low to find an affordable yet high quality DC motor for robotics, and a solid start to our Robot Motors section. After a lot of trial and error, testing dozens of motors, we have found what we believe to be a solid choice for small-medium sized robots weighing 2-5 lbs. The RPM make them an ideal choice for 3-4" wheels, and with an integrated encoder you can calculate odometry data to make your robots navigate the real world. This motor includes a 6-pin 2.0mm pitch PH JST...
Item #: ASM-RG-CASTER -
A simple but effective design, the Robot Geek 1-inch Ball Caster is meant to keep your mobile platform moving freely. Laser-cut Acrylic parts with an array of standoffs make assembly and mounting of various sizes easy. The 1-inch Acetal ball’s natural lubricity and resistance to moisture are advantageous to any mobile robotics platform. The total height of this ball caster is 1.1" with no spacers, you can also adjust the height by adding spacers and standoffs. Additional mounting...