Item #: MG-A000066 -
The Arduino Uno R3 is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Uno differs from all...
Item #: RG-GEEKDUINO -
The Geekduino is the new Arduino Compatible board from RobotGeek! This board goes into every RobotGeek Robot Kit and is the perfect microcontroller for your next robotic project! The Geekduino uses the ubiquitous Micro USB port to power and program the board. The Geekduino can also be powered via the ultra low-profile flat DC power jack. A series of switches allows you to toggle on/off the Geekduino's FTDI reset (handy for software projects) as well as change the operating voltage of the...
Item #: IL-ARBOTIXM -
The ArbotiX-M Robocontroller is at the heart of every Interbotix Robot. This versatile robot controller is an advanced control solution for BIOLOID and DYNAMIXEL based actuators. As an Arduino compatible microcontroller the Arbotix Robocontroller also benefits from a huge open source community of libraries and examples. Since its release in 2010 the Arbotix has quickly become a favorite among builders worldwide from hobby to high level research. The 'M' in ArbotiX-M stands for mini - this new...
Item #: MG-A000065 -
The Wireless SD Shield provides a 3.3v regulated Digi Xbee slot for easy wireless connectivity, a uSD (micro Secure Digital) slot for onboard storage capabilities, and a compact prototyping board area for custom additions. Transmission LED indicator lights, a reset button, and serial select switch are also available for your convenience. Passthrough headers allow for additional Shields to be stacked on top.More information available soon!
Item #: DF-DRI0009 -
The Arduino product family is a great learning platform for electronics, programming and robotics, but most projects at some point require mobility. The 2A Motor Shield For Arduino allows for motor control with Arduino right away! Stack up this shield on your controller and drive motors with higher power requirements. Depending on the motor of choice, you can make it fast or handle a higher payload. This Arduino Compatible Motor Shield (2A) uses L298P chip which allow to drive two 7-12V DC...
Item #: IL-ARBOTIXPRO -
The Arbotix-Pro is a robotics sub-controller based around the STM32F103 Cortex M3 ARM microprocessor. It functions as a ‘brain stem’ to a main CPU, allowing users to interface to servos, sensors, lower level communication buses such as TTL serial or I2C, and power all through one convenient USB connection and communication protocol.The Arbotix-Pro is built around using Dynamixel Robot actuators and has support for both TTL or RS-485 communication, to control AX, MX, and Dynamixel-PRO actuators...
Item #: DF-DFR0267 -
It's time to get Bluetooth 4.0 into your project and sync it up with your phone with the Bluno! For aficionados of smart devices and wearables, now you can go further and start prototyping with BLE integrated with your Arduino. Bluno is first of its kind in integrating BT 4.0 (BLE) module into Arduino Uno, making it an ideal prototyping platform for both software and hardware developers to go BLE. You will be able to develop your own smart bracelet , smart pedometer and more. Through the...
Item #: RG-RFIDUINO -
This page is for the RFIDuino V1.2. Visit this guide to see the differences between the Version 1.1 and 1.2 Hardware.The RFIDuino is an Arduino RFID Shield which makes Arduino RFID projects super easy to build. Just drop the RFIDuino Shield onto your Arduino microcontroller, load our sample code, and you'll be reading tags in no time! Our getting started guide will take you through the process of working with the RFIDuino from loading basic code to more advanced projects like triggering relays...
Item #: DF-DFR0225 -
RoMeo V2 is an All-in-One Arduino compatible microcontroller especially designed for robotics applications, and extended devices. Romeo benefits from the Arduino open source platform, it is supported by thousands of open source projects, and can easily be expanded with Arduino Shields. The integrated 2 way DC motor driver and Xbee socket allows you to start your project immediately without the need for an additional motor driver or wireless shield! Romeo V2 also supports stepper motor control....
Item #: SF-DEV12646 -
Is the Arduino Uno's hardware just not cutting it? Do you need a more powerful platform, but you're not ready to move away from the Arduino IDE? Then the Teensy is the perfect ARM based micorcontroller for your next robot project. The Teensy 3.1 is a complete USB-based microcontroller development system and is as versitile as it is powerful. A custom Teensy installer and bridge application will easily allow you to write sketches for the Teensy and load them on to the Teensy. All programming is...
Item #: MG-A000062 -
The Arduino Due represents the next generation of Arduino hardware. This board is based on the Atmel SAM3X8E ARM Cortex-M3 CPU, a 32-bit, 84 MHz microcontroller. This board will give you 96 Kbytes of SRAM, as well as 512 Kbytes of flash memory to hold store your code. The Due even has a DMA controller to help relieve the processor of memory intensive tasks. The Arduino Due has some amazing capabilities. It has 54 Digital I/O pins, 12 of which can be used for PWM. The Due can use any of these...
Item #: MG-A000057 -
The Arduino Uno is a great place to start in the Arduino World, but sometimes you need a few extra features to get your project up and running. The Arduino Leonardo , a variant of the Uno, is just the board you need! So what's so special about the Leonardo? The Leonardo can easily act as USB HID(Human Interface Device) such as a Keyboard or Mouse, opening a whole class of projects for you to explore with yout Arduino. This is accomlished by using the ATmega32u4, a microcontroller that acts...
Item #: MG-A000067 -
Overview The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter...
Item #: MG-A000063 -
Overview The Arduino ADK is a microcontroller board based on the ATmega2560 (datasheet). It has a USB host interface to connect with Android based phones, based on the MAX3421e IC. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. The ADK is based on the Mega 2560. Similar to the Mega 2560 and Uno, it features an...
Item #: SF-DEV-09219 -
It's blue! It's skinny! It's the Arduino Pro! SparkFun's minimal design approach to Arduino. This is a 5V Arduino running the 16MHz bootloader (select 'Arduino Duemilanove w/ 328' within the Arduino software). The power switch was moved to the side of the board (good idea Limor!) to allow control when a shield is attached. Please note: The right-angle power switch is fragile. We're working on making the switch stronger. For now, please be gentle. Arduino Pro does not come with connectors...
Item #: SF-DEV11113 -
It's blue! It's thin (0.8mm)! It's the Arduino Pro Mini! SparkFun's minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader (select 'Arduino Duemilanove w/ 328' within the Arduino software). Arduino Pro Mini does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We recommend first time Arduino users start with the Duemilanove. It's a great board that will get you up and running quickly. The Arduino...
Item #: SL-Netduino -
Software, meet hardware. Netduino is an open source electronics platform using the .NET Micro Framework. Featuring a 32-bit microcontroller and a rich development environment. Suitable for engineers and hobbyists alike. Code. Debug. Repeat. .NET Micro Framework combines the ease of high-level coding and the features of microcontrollers. Enjoy event-based programming, multi-threading, line-by-line debugging, breakpoints and more. Design files included. Netduino is an open source electronics...
Item #: KIT-RG-GEEKSHIELD -
Everything you need to be up and running with a Geekduino and Sensor shield I/O break out board to mount to your projects. GeekduinoSensor Shield10 Robotgeek sensor cablesDuino Mounting PlateThe Robotgeek Sensor Shield breaks out the digital and analog pins into easy to use 3-pin connectors. Each connector supplies 5 volts, ground, and a signal pin. These connectors can easily be connected to RobotGeek Sensors as well as a wide variety of sensors, actuators and output...
Item #: SS-ARD128D2P -
Seeeduino v3.0 328P is an Arduino-compatible board. Its design is based on Duemilanove scheme, 100% compatible to existing programs, shields and IDEs. On the hardware however, many changes have been made to improve the flexibility and user experience. Arduino is an open-source electronics prototyping platform based on flexible, easy-to-use hardware and software. It's intended for artists, designers, hobbyists, and anyone interested in creating interactive objects or environments. ...
Item #: SF-DEV-07914 -
Description: Riding on the waves of the very popular Arduino USB board is this small prototyping shield. Originally spawned with collaboration between the folks at SFE and ITP @ NYU, the Protoshield mates with the Arduino USB board and gives the user a small soldering area, two general LEDs, access to a BlueSMiRF socket, a general pushbutton switch, and most important of all - the Arduino reset switch is brought to the top level. This comes in kit form and must be soldered together by the end...
Item #: MG-A000072 -
The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100ethernet chip (datasheet). The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps...
Item #: MG-A000079 -
Are you ready to start controlling the universe with your Arduino? Or at least some beefier motors? Built around the L298 chip, the Arduino Motor Shield is a dual full-bridge driver. This shield is designed to drive inductive loads such as relays, solenoids, DC and stepping motors – anything your poor little Arduino would burn up on if it tried to drive them itself. You’ll be able to drive two motors via 8 pins on your Arduino. Each channel will allow you to control speed and direction, as...
Item #: SF-DEV-09815 -
This is a motor shield for Arduino that will control two DC motors. Based on the L298 H-bridge, the Ardumoto can drive up to 2 amps per channel. The board takes its power from the same Vin line as the Arduino board, includes blue and yellow LEDs to indicate active direction, and all driver lines are diode protected from back EMF. Control for motor attached to OUT1/2 is connected to digital line 12 (direction A) and digital line 10 (PWM A). Control for motor attached to OUT3/4 is...
Item #: SS-SLD63030P -
The Bluetooth Shield integrates a Serial Bluetooth module. It can be easily used with Arduino/Seeedstudio for transparent wireless serial communication. You can choose two pins from Arduino D0 to D7 as Software Serial Ports to communicate with Bluetooth Shield (D0 and D1 is Hardware Serial Port). The shield also has two Grove connectors (one is Digital, the other is Analog) for you to install Grove modules. Features Seeeduino/Arduino compatible Up to10m communication distance in house without...
Item #: SS-ARD105B1P -
The Danger Shield is an add-on for the Arduino & Freeduino micro controller boards. It contains a variety of fun and useful electronic circuits that you can use to do fun and useful things. It is a fully self-contained shield. You plug it into your Arduino, and you can immediately start using it. No extra things to hook up, no external components. Just a really rad board ready to rock. Note: This is a kit- Assembly & Soldering is required. Some of the features of the board are: 3...
Item #: SS-SLD01106P -
The EL Shield kit is an easy to use shield to control electroluminescent (EL) devices (such as EL wire) with either an Arduino or Seeeduino. The board has 4 outputs so you can control up to 4 devices separately! It can drive EL wires at long as 15 m (49 ft). This shield come without the headers soldered on, so you'll have to attach them before use. If you know how to control an LED, you can control EL devices. The EL Shield makes it that easy! The shield uses pulse-width modulation (PWM), so...
Item #: SS-SLD33149P -
Description The GPRS (General Packet Radio Service) Shield is a new nonvoice value added service that delivers GSM/GPRS 850/900/1800/1900MHz performance for voice, SMS, Data, and Fax in a small form factor and with low power consumption. It is controlled via AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands), and fully compatible with Seeeduino/Arduino and Mega. The GPRS Shield has 12 GPIOs 2 PWMs and 1 ADC(They are all 2V8 logic). Features Quad-Band 850/ 900/ 1800/ 1900 MHz GPRS...
Item #: SS-SLD80256P -
Quickly add motor control to your Arduino or Seeeduino with the Grove Motor Shield! You can use the shield to easily connect 2 brushed DC motors, which makes it great for controlling wheeled platforms like the Budget Bot Chassis. Use the Grove Motor Shield to control motors from 6-15 volts, with up to 2 amps per channel. Easily accessible screw terminals will let you connect your motors and external power. This shield is also great if you're using the Grove sensors, since it has 13 Grove ports...
Item #: SS-INT109B2P -
Every project is better with music! Build your own music player with the music shield. Or use it to give your robot a voice and/or sound effects. The Music Shield is an ipod/iphone dock compatible shield. It can work with Arduino, Seeeduino, Seeeduino Mega and Arduino Mega2560. It is based on the VS1053b and can play variety of music format stored on MicroSD card with Seeed Studio provided Arduino Library. Note: Recording is only supported by Seeeduino Mega and Arduino Mega2560. Documentation...
Item #: MG-E000008 -
If you need a lot of inputs and/or outputs, this is your solution! The Mux (Multiplexer) Shield adds the capacity for up to 48 inputs or outputs on the Arduino and Arduino Mega. Using three Texas Instruments CD74HC4067 Analog Multiplexers, the Mux Shield makes it possible to have 48 analog/digital inputs or digital outputs in many combinations. The Mux Shield comes with 5V and Ground headers so you'll have power available to each input or output and comes with stackable headers installed. The...
Item #: RG-SENSHIELDV2 -
The Arduino Platform is a great way for learning about electronics and programming, as well as creating microcontoller based projects. But even simple projects can get messy very quickly, leaving you with a pile of wires, breadboards, and components. With the RobotGeek Sensor System, you can put your project on the fast track and get it up and running in no time. The RobotGeek Sensor Shield will fit on any Standard Arduino Compatible board*, and break out the digital and analog pins into easy...
Item #: SS-WLS06201P -
Seeed's Wifi Shield utilizes a RN171 wifi module to provide your Arduino with serial ethernet function. It only takes two pins to hook your device up to 802.11 b/g wireless networks! It features an independent antenna which can cover a wider range and transmit stronger signals. The wifi shield supports common TCP, UDP and FTP communication protocols creating a perfect solution to most wireless network projects such as smart home networks, robotic control, personal weather stations,...
Item #: SS-SLD01103P -
The newest version of the Xbee Shield is a standardized and stackable shield for Arduino. You can easily stack any modules from the Bee series and build a wireless network for your project! In spite of that, it is also equipped with the function of level conversion which enables a double-way conversion between high and low IO levels. The reversed digital pins facilitate users to select TX-RX ports using jumper caps.***Seeed Studio's XBee Shield V2.0 comes unassembled and will require soldering...
Item #: SS-SLD62445P -
2.8'' TFT Touch Shield is an Arduino / Arduino Mega compatible multicolored TFT display with a 4-wire resistive touch-screen. It is available in an Arduino shield compatible pinout for attachment. The TFT driver is based on ST7781R with 8bit data and 4bit control interface. Arduino / Mega Shield compatible footprint. TFT Resolution : 240 x 320 pixels Size : 2.8" (50.0 x 69.2 x 2.5 mm) Colors : 262K Backlight : LED Driver IC: ST7781R 4-Wire Resistive Touch Screen Application Ideas As a...
Item #: SS-INT108B1P -
A Protoshield kit for Seeeduino/Arduino MEGA. Miles of space with a huge amount of header options. Kit also comes with 5 button switches. Excellent kit for building your own MEGA shield. Features Supports both Seeeduino MEGA and Arduino MEGA All pins are brought to the top level Supports Xbee/GPS bee Rest button brought to the top level 5 button switches Tons of male and female headers Product WIKI Page. ...
Item #: MG-A000009 -
What we have here is a (flame retardant) Arduino Project Box that allows you to safely enclose your Arduino + Shield projects and then set them on fire. Just kidding, please don't. But seriously! Rob your Arduino projects of their nudist free spirit attitudes and put some clothes on them, dang hippies. This enclosure can fit pretty much all Arduino and Arduino Mega models, as well as a majority of shields. It has specifically designed removable ports for use with the Arduino Ethernet shield....
Item #: C-400-GSA-Book -
This valuable little book offers a thorough introduction to the open-source electronics prototyping platform that's taking the design and hobbyist world by storm. Getting Started with Arduino gives you lots of ideas for Arduino projects and helps you get going on them right away. From getting organized to putting the final touches on your prototype, all the information you need is right in the book. Inside, you'll learn about: Interaction design and physical computing The Arduino hardware and...
Item #: SS-POW10301P -
The Robust EL Inverter For EL Shield turns DC voltage from your Arduino or Geekduino into high frequency AC for powering electroluminescent (EL) devices. The rated input voltage is 3.3-5 V, so it should work well with most micro-controllers. It produces high frequency 110 V AC which is perfect for powering EL wire. Keep in mind that it does produce a quiet but audible high frequency noise when connected to power. In most applications it won't be noticeable. This inverter can power up to 15 m...
Item #: ASM-ARBX-CMD-V2 -
The ArbotiX Commander v2.0 is an Arduino compatible, open-source XBEE-wireless hand-held controller built specifically for controlling ArbotiX/NUKE powered walking robots (but it can be interfaced to virtually any microcontroller or PC). This gamepad style controller comes ready to be setup with the ArbotiX Robocontroller. The ArbotiX Commander v2.0 was meant to be hacked, modified, upgraded, and otherwise tinkered with, and uses a simple serial protocol to interface with other Xbee enabled...
Item #: SS-ARD121D2P -
Overview Seeeduino Mega is a microntrolller board based on ATmega1280, derived from Arduino Mega with changes in pursuit for small form factor, flexibility and functionality.It has 70 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with...
Item #: SS-ELB127E4P -
Electronic Brick Chassis is a modular 'plug n play' style dedicated Arduino, Seeeduino, and Freeduino interface shield. It breaks out your Duino's available I/O with convenient 3-pin ports and data buses. Plug in a variety of Phidgets & Electronic Brick Sensors, Inputs, Outputs, and Accessories! Yes! We can build electronics projects just as easy as piling bricks. The Arduino/Freeduino movement has made programming and physical computing easier than ever. The Electronic Brick...
Item #: ASM-RG-DUINOMNT -
The Duino Mounting Plate converts the Arduino three hole pattern to the standard Robot Geek hole pattern. All Robot Geek kits, sensors, and components conform to a 1 x 1 centimeter grid making it easy to custom build your projects any way you desire. The Duino Mounting Plate allows you to easily mount and move your Arduino boards anywhere you want on your Robot Geek projects.*NOTE: The Duino Mounting plate does not come with the Geekduino.