Motors, Servos, Actuators
Motors, Servos, Actuators

Show
12v DC Motor Pump - Full View
TI-TG-02B-DC12B
Price: $24.95 In Stock
Item #: TI-TG-02B-DC12B -

If you are looking for an Arduino Pump the RobotGeek Large Liquid Pump is a great solution. This pump is self priming, quiet, food safe, and can move up to 2 liters per minute. To use this for an Arduino Pump project all you need is a RobotGeek Relay and seperate power supply. The pump will work with standard aquarium tubing. The fit is a little tight, but the tubing will go on. We recommend picking up some of our 3.5mm food safe silicone tubing which fits great and goes on easier! Recommended...

RobotGeek 12v Mini Self-Priming Pump
RG-SMPUMP
Price: $17.95 In Stock
Item #: RG-SMPUMP -

If you are looking for an Arduino Pump the RobotGeek small liquid and air pump is a great solution. This pump is self priming and food safe so it can be used for projects involving plant watering, suction, drainage, drink dispensing, barbots, and more. To use this for an Arduino Pump project all you need is a RobotGeek Relay and seperate power supply. The pump can operate at either 6 or 12 volts and packs a punch in a small package! Recommended Arduino Pump Tutorials: Arduino ShotBot Project...

Solenoid Valve arduino Solenoid valve, arduino solenoid water valve, solenoid liquid valve, arduino solenoid valve, arduino water valve, arduino liquid valve
HW-WVALVE
Price: $19.95 In Stock
Item #: HW-WVALVE -

If you are looking for an Arduino solenoid valve the RobotGeek liquid solenoid valve is a perfect solution. Compact, food safe, and with mounting holes make it a great fit for DIY projects of all kinds. The Solenoid Valve is a great companion to the Large DC Liquid Pump and the Small DC Liquid Pump. When building pumping projects sometimes it is necessary to add a valve to stop either liquid back draw or unwanted flow. When using diaphram pumps if your liquid supply is higher than your pouring...

RobotGeek 180 Degree Robot Servo robot servo, 180 degree robot servo, robotgeek servo, robotgeek robot servo, robotgeek 180 degree servo, 180 degree servo
ASM-RGS-13
Retail: $24.95
Price: $19.95 In Stock
Item #: ASM-RGS-13 -

Get ready to bring your robotic dreams to life with the RobotGeek 180 Degree Robot Servo! This metal-geared servo is perfect for building robotic joints and will help you create your own custom robotic arms, crawlers, and more! And because these servos use a standard PWM signal for control, they're easy to directly interface with microcontrollers like the Arduino! Idler Horn The difference between a regular servo and robot servo is the Idle Horn. This horn will spin freely and is at the...

RobotGeek Continuous Rotation Servo robotgeek 360 degree robot servo, robotgeek continuous servo, robotgeek robot servo, robot servo, robotgeek servo, continuous robot servo, continuous servo,Continuous Rotation
ASM-RGS-4C
Retail: $24.95
Price: $19.95 In Stock
Item #: ASM-RGS-4C -

Get ready to bring your robotic dreams to life with the RobotGeek Continuous Rotation Servo! This metal-geared servo is perfect for building robotic rovers, spinners and more! And because these servos use a standard PWM signal for control, they're easy to directly interface with microcontrollers like the Arduino! Idler Horn The difference between a regular servo and robot servo is the Idle Horn. This horn will spin freely and is at the opposite position of the main drive horn. The idler horn...

Sabertooth dual 5A motor driver
C-100-DC-2x5
Price: $59.99 Back Order
Item #: C-100-DC-2x5 -

Product Description Sabertooth 2X5 is the motor driver of choice for small differential-drive robots. It is ideal for smaller robots- up to 3lbs in combat or 25 lbs for general purpose use. It is also a great choice in any application where you need to control two brushed motors. Out of the box, the Sabertooth can supply two DC brushed motors with up to 5A each continuously. Peak currents of 10A are achievable for short periods. Because Sabertooth 2x5 incorporates soft current limiting and...

Grove - L298 Dual H-Bridge I2C Motor Driver Grove Motor driver, Arduino motor driver, arduino h-bridge, L298 Dual H-Bridge I2C Motor Driver, L298 motor driver, Grove L298 motor
SS-ROB72212P
Price: $23.50 In Stock
Item #: SS-ROB72212P -

Description The Grove I2C motor driver is a new addition to the Grove series with the same easy-to-use interface. Its heart is a dual channel H-bridge driver chip that can handle current up to 2A per channel, controlled by an Atmel ATmega8L which handles the I2C communication with for example an Arduino. Both motors can be driven simultaneously while set to a different speed and direction. It can power two brushed DC motors or one 4-wire two-phase stepper motor. It requires a 6V to 15V power...

Sabertooth dual 25A motor driver
C-100-DC-2x25
Price: $124.99 Back Order
Item #: C-100-DC-2x25 -

The Sabertooth 2X25 is one of the most versatile, efficient and easy to use dual motor drivers on the market. It is suitable for high powered robots - up to 100lbs in combat or 300lbs for general purpose robotics.  Out of the box, the Sabertooth can supply two DC brushed motors with up to 25A each. Peak currents of 50A per channel are achievable for a few seconds.  Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental...

Sabertooth dual 5A motor driver for R/C
C-100-DC-2x5RC
Price: $59.99 In Stock
Item #: C-100-DC-2x5RC -

Product Description Sabertooth 2X5 R/C is a dual motor driver specifically optimized for use in radio controlled vehicles. It is suitable for small robots, cars and boats, and especially well suited for the Antweight and Beetleweight classes of fighting robots. Out of the box, it can supply two DC brushed motors with up to 5A each. Peak currents of 10A are achievable for a few seconds. Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental...

SyRen 10A regenerative motor driver
C-100-DC-SYREN10
Price: $49.99 In Stock
Item #: C-100-DC-SYREN10 -

Product Description The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. It is suitable for medium powered robots - up to 30lbs in combat or 100lbs for general purpose robotics. Out of the box, the SyRen 10 can supply a single DC brushed motor with up to 10A continuously. Peak currents of 15A are achievable for a few seconds. Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental stalls...

RG90 Gear Motor RG90 Gear Motor, MOT-VIB08, Gear Motor, gearmotor, 6v gearmotor, 90rpm, 1:120, Arduino Motor, Robot Motor
MOT-VIBO8
Price: $5.95 In Stock
Item #: MOT-VIBO8 -

Weighing in at just 35 grams, this RG90 Gear Motor can put put an impressive 1.2 kg/cm of torque! That makes it great for small, wheeled robots! The double-flat output shaft is 7mm in diameter and is perfect for attaching to our Gear Motor Wheel. Our gear motors come with two- 300mm wires pre-soldered onto the motor. Each wire is terminated with a 2.54mm female connector. This makes them ideal for attaching to any 2.54mm pin connector. RG90 Gear Motor Operating Voltage 6V No Load Speed 90 RPM...

Sabertooth Dual 60A Motor Driver Sabertooth Dual 60A Motor Driver
DE-Sabertooth2X60
Price: $189.99 Back Order
Item #: DE-Sabertooth2X60 -

The Sabertooth 2X60 is one of the most versatile, efficient and easy to use dual motor drivers on the market. It is suitable for high powered robots - up to 120lbs in combat or up to 1000lbs for general purpose robotics.  Out of the box, the Sabertooth can supply two DC brushed motors with up to 60A each. Peak currents of 120A per channel are achievable for a few seconds.  Overcurrent and thermal protection means you'll never have to worry about killing the driver with...

SyRen 25A regenerative motor driver
C-100-DC-SYREN25
Price: $74.99 In Stock
Item #: C-100-DC-SYREN25 -

Product Description The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. It is suitable for medium powered robots - up to 50lbs in combat or 180lbs for general purpose robotics. Out of the box, the SyRen 25 can supply a single DC brushed motor with up to 25A continuously. Peak currents of 45A are achievable for a few seconds. Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental stalls...

Sabertooth dual 12A motor driver
C-100-DC-2x12
Price: $79.99 In Stock
Item #: C-100-DC-2x12 -

Product Description The Sabertooth 2X12 is one of the most versatile, efficient and easy to use dual motor drivers on the market. It is suitable for medium powered robots - up to 30lbs in combat or 100lbs for general purpose robotics.  Out of the box, the Sabertooth can supply two DC brushed motors with up to 12A each. Peak currents of 25A are achievable for a few seconds.  Overcurrent and thermal protection means you'll never have to worry about killing the driver with...

Sabertooth dual 12A motor driver for R/C
C-100-DC-2x12RC
Price: $64.99 In Stock
Item #: C-100-DC-2x12RC -

Sabertooth 2X12 R/C is a dual motor driver specifically optimized for use in radio controlled vehicles. It is suitable for medium powered robots, cars and boats. The Sabertooth 2x12 R/C replaces our 2x10 RC controller. Out of the box, it can supply two DC brushed motors with up to 12A each. Peak currents of 25A are achievable for a few seconds. Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental stalls or by hooking up too big a motor....

Bipolar Stepper Motor
SF-ROB-09238
Price: $14.95 In Stock
Item #: SF-ROB-09238 -

Description: This is a simple, but very powerful stepper motor with a 4-wire cable attached. Features: Step Angle (degrees) :1.8 2 Phase Rated Voltage : 15.4V Rated Current : 0.28A Holding Torque : 2.4kg*cm Detent Torque : 120g*cm Documents: Datasheet ...

Dual VNH3SP30 Motor Driver Carrier MD03A Dual, VNH3SP30, Motor, Driver, Carrier, MD03A, DC, Controller
PO-707
Price: $49.99 Back Order
Item #: PO-707 -

If you are looking to drive two high-power motors through one compact unit, these dual VNH3SP30 motor driver carriers are perfect for you. With these boards, it's easy to get a medium-sized, differential drive robot running in no time. The Pololu dual high-power motor drivers are compact carriers for the VNH3SP30 and VNH2SP30 motor driver integrated circuits from ST. The board incorporates most of the components of the typical application diagram on page 8 of the VNH2SP30 datasheet, including...

HB-25 Motor Controller
PX-29144
Price: $49.99 In Stock
Item #: PX-29144 -

The Parallax HB-25 Motor Controller is one of our best solutions for DC motor control. This module is dependable and highly-compatible with any microcontroller that can generate a servo compatible pulse. In the simplest sense the HB-25 allows a DC Motor to be controlled much like a Continuous Rotation Servo. While the signals are compatible, the HB-25 does not require refreshing as a servo does. A single pulse can maintain the output.   The HB-25 Motor Controller has the...

L12 100mm 100:1 Linear Actuator Firgelli Linear Actuator, mini linear actuator, small linear actuator, small arduino linear actuator
FR-L12-100-100-6-I
Price: $90.00 In Stock
Item #: FR-L12-100-100-6-I -

Firgelli mini linear actuators are excellent for DIY and Arduino mini linear actuator projects. The L12-I series can be controlled from a regular servo PWM signal as well as voltage and current signaling. The PWM control is perfect for Arduino linear actuator projects because the actuator can be controlled just like a servo using the servo library. We recommend checking out our Arduino Linear Actuator Tutorials listed below. Each linear actuator also comes with mounting hardware and end...

L12 100mm 210:1 Linear Actuator small linear actuator, mini arduino linear actuator, Firgelli Linear Actuator, micro linear actuator
FR-L12-100-210-6-I
Price: $90.00 In Stock
Item #: FR-L12-100-210-6-I -

Firgelli mini linear actuators are excellent for DIY and Arduino mini linear actuator projects. The L12-I series can be controlled from a regular servo PWM signal as well as voltage and current signaling. The PWM control is perfect for Arduino linear actuator projects because the actuator can be controlled just like a servo using the servo library. We recommend checking out our Arduino Linear Actuator Tutorials listed below. Each linear actuator also comes with mounting hardware and end...

L12 50mm 100:1 Linear Actuator Firgelli Linear Actuator, mini linear actuator, small linear actuator, small arduino linear actuator
FR-L12-50-100-6-I
Price: $90.00 In Stock
Item #: FR-L12-50-100-6-I -

Firgelli mini linear actuators are excellent for DIY and Arduino mini linear actuator projects. The L12-I series can be controlled from a regular servo PWM signal as well as voltage and current signaling. The PWM control is perfect for Arduino linear actuator projects because the actuator can be controlled just like a servo using the servo library. We recommend checking out our Arduino Linear Actuator Tutorials listed below. Each linear actuator also comes with mounting hardware and end...

L12 50mm 210:1 Linear Actuator small linear actuator, small arduino linear actuator, Firgelli Linear Actuator, mini linear actuator
FR-L12-50-210-6-I
Price: $90.00 In Stock
Item #: FR-L12-50-210-6-I -

Firgelli mini linear actuators are excellent for DIY and Arduino mini linear actuator projects. The L12-I series can be controlled from a regular servo PWM signal as well as voltage and current signaling. The PWM control is perfect for Arduino linear actuator projects because the actuator can be controlled just like a servo using the servo library. We recommend checking out our Arduino Linear Actuator Tutorials listed below. Each linear actuator also comes with mounting hardware and end...

L298 Dual H-Bridge Motor Driver L298 Dual H-Bridge Motor Driver
SS-MOT103B1M
Price: $23.50 In Stock
Item #: SS-MOT103B1M -

Double H driver module uses ST L298N dual full-bridge driver, an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the input signals. The emitters of the lower transistors of each bridge are connected together...

Motor Driver 1A Dual TB6612FNG
SF-ROB-09457
Price: $8.95 Back Order
Item #: SF-ROB-09457 -

The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - CW, CCW, short-brake, and stop. The two motor outputs (A and B) can be separately controlled, the speed of each motor is controlled via a PWM input signal with a frequency up to 100kHz. The STBY pin should be pulled high to take the motor out of standby mode. Logic supply voltage (VCC) can be in...

Unipolar Stepper Motor 12VDC
M-200-403-1010ND
Price: $27.50 In Stock
Item #: M-200-403-1010ND -

Voltage - Rated 12VDC Size - 42mm x 49.5mm x 3mm Type - Unipolar Holding Torque - 73.4/10.4 Step Angle - 7.5° Steps per Revolution - 48

Unipolar Stepper Motor 5VDC 7.5DEG
M-200-403-1019ND
Price: $20.00 In Stock
Item #: M-200-403-1019ND -

Voltage - Rated 5VDC Size - 26mm x 34.9mm x 2mm Type - Unipolar Holding Torque - 19.2/1.3 Step Angle - 7.5° Steps per Revolution - 48

2 Inch Stroke 110 LB Linear Actuator with Feedback Linear Actuator, push actuator, SPAL
M-200-50-5-1577-2
Price: $107.95 In Stock
Item #: M-200-50-5-1577-2 -

This is a 12V DC 110lb Linear Actuator from Creative Werks. (part number LACT2P) These are reliable, well built tough linear actuators. The sturdy mounting brackets make them easy to mount and won't break. If you are looking for a basic manual controller we recommend the Linear Actuator Controller kit. If you are looking to control these from an Arduino we recommend checking out the Arduino Linear Actuator tutorials below! Arduino Linear Actuator Tutorials: Preset Position Button Control of a...

4 Inch Stroke 110 LB Linear Actuator with Feedback large Linear Actuator, large arduino linear actuator, linear actuator for arduino
M-200-50-5-1577-4
Price: $109.95 Back Order
Item #: M-200-50-5-1577-4 -

This is a 12V DC 110lb Linear Actuator from Creative Werks. (part number LACT2P) These are reliable, well built tough linear actuators. The sturdy mounting brackets make them easy to mount and won't break. If you are looking for a basic manual controller we recommend the Linear Actuator Controller kit. If you are looking to control these from an Arduino we recommend checking out the Arduino Linear Actuator tutorials below! Arduino Linear Actuator Tutorials: Preset Position Button Control of a...

6 Inch Stroke 110 LB Linear Actuator with Feedback large Linear Actuator, large arduino linear actuator, linear actuator for arduino
M-200-50-5-1577-6
Price: $109.95 In Stock
Item #: M-200-50-5-1577-6 -

This is a 12V DC 110lb Linear Actuator from Creative Werks. (part number LACT2P) These are reliable, well built tough linear actuators. The sturdy mounting brackets make them easy to mount and won't break. If you are looking for a basic manual controller we recommend the Linear Actuator Controller kit. If you are looking to control these from an Arduino we recommend checking out the Arduino Linear Actuator tutorials below! Arduino Linear Actuator Tutorials: Preset Position Button Control of a...

8 Inch Stroke 110 LB Linear Actuator with Feedback large Linear Actuator, large arduino linear actuator, linear actuator for arduino
M-200-50-5-1577-8
Price: $109.95 In Stock
Item #: M-200-50-5-1577-8 -

This is a 12V DC 110lb Linear Actuator from Creative Werks. (part number LACT2P) These are reliable, well built tough linear actuators. The sturdy mounting brackets make them easy to mount and won't break. If you are looking for a basic manual controller we recommend the Linear Actuator Controller kit. If you are looking to control these from an Arduino we recommend checking out the Arduino Linear Actuator tutorials below! Arduino Linear Actuator Tutorials: Preset Position Button Control of a...

10 Inch Stroke 110 LB Linear Actuator with Feedback large Linear Actuator, large arduino linear actuator, linear actuator for arduino
M-200-50-5-1577-10
Price: $113.95 In Stock
Item #: M-200-50-5-1577-10 -

This is a 12V DC 110lb Linear Actuator from Creative Werks. (part number LACT2P) These are reliable, well built tough linear actuators. The sturdy mounting brackets make them easy to mount and won't break. If you are looking for a basic manual controller we recommend the Linear Actuator Controller kit. If you are looking to control these from an Arduino we recommend checking out the Arduino Linear Actuator tutorials below! Arduino Linear Actuator Tutorials: Preset Position Button Control of a...

12 Inch Stroke 110 LB Linear Actuator with Feedback Linear Actuator, push actuator, SPAL
M-200-50-5-1577-12
Price: $113.95 In Stock
Item #: M-200-50-5-1577-12 -

This is a 12V DC 110lb Linear Actuator from Creative Werks. (part number LACT2P) These are reliable, well built tough linear actuators. The sturdy mounting brackets make them easy to mount and won't break. If you are looking for a basic manual controller we recommend the Linear Actuator Controller kit. If you are looking to control these from an Arduino we recommend checking out the Arduino Linear Actuator tutorials below! Arduino Linear Actuator Tutorials: Preset Position Button Control of a...

Linear Actuator Mounting Bracket spal, linear actuator, mounting bracket
M-200-50-5-1577-B
Price: $14.25 In Stock
Item #: M-200-50-5-1577-B -

LINEAR ACTUATOR MOUNTING BRACKET SPAL part number LA-BRACKET-110A mounting bracket kit for use with SPAL/Creative Werks LACTP series linear actuators. Bracket and mounting pad are made from billet aluminum. Includes hardware. NOTE: This is a single bracket. If you need to mount both ends of your linear actuator you will need two brackets. SPECIFICATIONS CLEVIS Inside width 13/16" Outside width 1-1/2" Throat depth 9/16" Bracket size 1-5/16" x 1-1/2" x 1-13/32" Pad...

10 Foot Extension Wire spal, linear actuator, actuator controller, wiring harness
M-200-50-5-1577-H
Price: $14.95 In Stock
Item #: M-200-50-5-1577-H -

10 FOOT EXTENSION HARNESS Creative Werks part number LA-EXTHARN. Ten foot wiring harness allows a Creative Werks 12 VDC 110 lb. linear actuator to be mounted up to ten feet away from the actuator controller. SPECIFICATIONS 10 feet long Shpg. 1/4 lb.

FS90 Analog Micro Plastic Gear Servo FS90 Analog Micro Plastic Gear Servo, analog micro servo, plastic gear servo, 9g plastic servo, 9g servo, micro servo, analog servo, 9g micro servo
FT-FS90
Price: $6.95 In Stock
Item #: FT-FS90 -

Need a tiny servo for a tiny task? Try the FS90 Micro Plastic Gear Servo! This servo is great for scanning type sensors, tiny robots, and more! Each servo comes with a variety of horns. These servos use a standard PWM signal to control them. The Arduino does a great job of controlling PWM Servos, making it ideal for a variety of robotic projects. But sometimes powering these servos can be problematic. Powering servos from the Arduino's 5v regulator leads to underpowered servos, limited by both...

Robot Geek 9G mount
ASM-9GM
Price: $4.95 In Stock
Item #: ASM-9GM -

This mount works with our plastic gear 9g servo and our metal gear 9g servo.The RobotGeek 9g Mount is a simple way to mount your 9g servos to any RobotGeek deck or platform. The mount and two standoffs conform to the Robot Geek 1 X 1 CM grid used in all RobotGeek kits. The standoffs in this kit are 20mm tall.If you are looking to mount a Sharp IR Range sensor on your servo check out our IR Sensor Mounting Kit! ...

FS90MG Micro Metal Gear Servo Fitec FS90MG Micro Metal Gear Servo, metal gear servo, 9g servo, 9g metal gear servo, 9g micro metal gear servo, 9g metal servo, metal gear servo, micro servo
FT-FS90MG
Price: $9.95 In Stock
Item #: FT-FS90MG -

Need a tiny servo for a tiny task? Try the FS90 Micro Plastic Gear Servo! This servo is great for scanning type sensors, tiny robots, and more! Each servo comes with a variety of horns. The metal gears give this servo even more power and durability! These servos use a standard PWM signal to control them. The Arduino does a great job of controlling PWM Servos, making it ideal for a variety of robotic projects. But sometimes powering these servos can be problematic. Powering servos from the...

Parallax (Futaba) Continuous Rotation Servo servo, servos, continuous rotation servo, continuous servo
PX-900-00008
Price: $10.00 In Stock
Item #: PX-900-00008 -

The Parallax Continuous Rotation Servo is a Futaba S148 servo. It's recommended for robotics projects and includes an adjustable potentiometer to center the servo. Servos may be controlled directly from a BASIC Stamp I/O pin by using the PULSOUT command. Servo has been modified for continuous rotation. NOTES:This continuous rotation servo only work with the following brackets: E-Z Aluminum Servo Bracket , Multi-Purpose Servo Bracket, & Aluminum Servo Bracket (may need some custom...

RobotGeek Servo C Bracket robotgeek servo c bracket, c bracket, robotgeek bracket, robotgeek servo bracket, servo bracket, servo c bracket
RG-CBRACKET
Price: $4.95 In Stock
Item #: RG-CBRACKET -

The RobotGeek Servo C Bracket is a great tool for creating joints with your RobotGeek Servo. This bracket easily attaches to the servo's horns with just a few bolts. A variety of mounting holes on the bracket make it easy to mount the bracket to your robot or sensors in a variety of ways. The circular hole pattern on the bottom of the bracket will also attach directly to a RobotGeek Servo Horn or other brackets, allowing you to easily build up complex servo systems. Do you need hardware?...

RobotGeek Servo Side Bracket robotgeek servo side bracket, servo side bracket, side bracket, rg side bracket, side bracket
HW-SBRACKET
Price: $4.95 In Stock
Item #: HW-SBRACKET -

The RobotGeek Servo Side Bracket is the perfect way to mount your RobotGeek Servo to other servos and your Robot. The side bracket can attach to 5 different positions on the servo rail to make it easy to configure your robot the way you want it. The circular hole pattern on the bottom of the bracket will also attach directly to a RobotGeek Servo Horn or other brackets, allowing you to easily build up complex servo systems. Do you need hardware? RobotGeek Servos come with metric nuts and bolts,...

37D mm Metal Gearmotor Bracket Pair 37D mm Metal Gearmotor Bracket Pair, Gearmotor Bracket, Pololu, 37D mm Metal Gearmotor, Robot Bracket, Robot Motor Bracket
PO-1084
Price: $7.95 In Stock
Item #: PO-1084 -

These light-weight brackets (under 15 g each) are specifically designed for the Pololu 37D mm metal gearmotors, such as the 19:1 metal gearmotor 37Dx52L mm and the 19:1 metal gearmotor 37Dx52L mm with 64 CPR encoder. Each bracket features seven mounting holes for M3 or #4-size screws along each edge, giving you a variety of mounting options. A total of twelve M3 screws (six for each bracket) are included for securing the motor to the bracket. NOTE: This set contains 2 brackets and DOES NOT...

Gear Motor w/ Wheel Set gear motor wheel set, gear motor,RG90 Gear Motor, MOT-VIB08, Gear Motor, gearmotor, 6v gearmotor, 90rpm, 1:120, Arduino Motor, Robot Motor
ASM-GM-WHL-SET
Price: $18.50 In Stock
Item #: ASM-GM-WHL-SET -

This kit is a combination of two RG 90 Gear Motors and two matching Gear Motor Wheels.The variety of mounting holes on the gear motors will make them easy to mount to almost any chassis. With a weight of 18g, this set is a great choice for small robots and rovers. RG90 Gear Motor Operating Voltage 6V No Load Speed 90 RPM No Load Current 150 mA Stall Current 800 mA Output Torque 1.2 kg/cm Gear Ratio 1:120 Overall Dimensions 54x42x23mm Weight 35 grams Technical Drawing                          ...

Gear Motor Acrylic Wheel Assembled
ASM-GMW
Price: $3.50 In Stock
Item #: ASM-GMW -

Do you need a wheel for your latest rover? Try our new Gear Motor Wheels! These wheels are made of a red acrylic, wrapped in a black rubber tire. Each wheel has a double-flat, 7mm in diameter hole -prefect for our RG 90 Gear Motors! Just use the included hardware to attach the wheels to the motors and your robot will be rolling in no time.

Large Solenoid Front
ASM-SOL-LG
Price: $19.95 In Stock
Item #: ASM-SOL-LG -

If you are looking for a solenoid for your DIY, educational, or Arduino solenoid project the RobotGeek solenoids are a great choice. This is the Large version of the solenoid line with a plunger travel of 12mm and up to 3468 g/7.65 lbs of force. (View the specifications tab for full information.) If you want to control this solenoid from your Arduino all you need is to add a RobotGeek Relay and power source and you have an Arduino Solenoid project! Check out our Arduino Solenoid Tutorial for...

medium solenoid
ASM-SOL-MD
Price: $14.95 In Stock
Item #: ASM-SOL-MD -

If you are looking for a solenoid for your DIY, educational, or Arduino solenoid project the RobotGeek solenoids are a great choice. This is the Medium version of the solenoid line with a plunger travel of 7mm and up to 1800 g/3.97 lbs lbs of force. (View the specifications tab for full information.) If you want to control this solenoid from your Arduino all you need is to add a RobotGeek Relay and power source and you have an Arduino Solenoid project! Check out our Arduino Solenoid Tutorial...

Mini Turbo Fan Mini Turbo Fan
MP-EPF200
Price: $13.95 In Stock
Item #: MP-EPF200 -

The Mini Turbo Fan is a Mini Badass. Sporting 73g of thrust while weighing in at only 30g it can take off if you give it full throttle. Perfect for fire fighting robots or cooling you on hot summer days. The Mini Turbo Fan comes with a heat sink and 4" cable with male ends. To extend the cable we recommend using our 2-pin F/F jumper cable. *The fan edges may rub against the duct walls when you first run it. This is okay. The blades will actually trim themselves down. That is how badass this...

Robot DC Gearhead Motor - 6v 180rpm w/ Encoder Robot Motor, DC Gearhead Motor, Motor Encoder, Gearhead Motor Encoder, Gearhead Motor, Robot Gearhead Motor, Robot Gearhead Motor Encoder
KIT-MTR-36-06-180
Price: $29.95 In Stock
Item #: KIT-MTR-36-06-180 -

We searched high and low to find an affordable yet high quality DC motor for robotics, and a solid start to our Robot Motors section. After a lot of trial and error, testing dozens of motors, we have found what we believe to be a solid choice for small-medium sized robots weighing 2-5 lbs. The RPM make them an ideal choice for 3-4" wheels, and with an integrated encoder you can calculate odometry data to make your robots navigate the real world. This motor includes a 6-pin 2.0mm pitch PH JST...

RobotGeek 1" Pastic Ball Caster
ASM-RG-CASTER
Price: $6.95 In Stock
Item #: ASM-RG-CASTER -

A simple but effective design, the Robot Geek 1-inch Ball Caster is meant to keep your mobile platform moving freely. Laser-cut Acrylic parts with an array of standoffs make assembly and mounting of various sizes easy. The 1-inch Acetal ball’s natural lubricity and resistance to moisture are advantageous to any mobile robotics platform. The total height of this ball caster is 1.1" with no spacers, you can also adjust the height by adding spacers and standoffs. Additional mounting...