Power, Cables, Accessories
Power, Cables, Accessories

Show
USB A Male to B Male - 6ft Cable USB A to B 6ft
CBL-USBA2B
Price: $4.95 In Stock
Item #: CBL-USBA2B -

    It is a standard USB A to B cable. It is 6 feet long. It has gold plated connectors. Not much else to say. Buy one if you need it. Or don't. It won't hurt our feelings honestly.

    Premium USB to Micro USB Charge & Sync Cable - 6ft
    CBL-USB2MICRO
    Price: $6.95 In Stock
    Item #: CBL-USB2MICRO -

      This 6ft Micro USB Cable is perfect for powering and programming controllers like the RobotGeek Geekduino

      2.1mm DC Barrel Jack to Alligator Clips 2.1mm, dc, jack, barrel, plug, alligator, clips, power, cord, testing
      AF-1328
      Price: $1.95 In Stock
      Item #: AF-1328 -

        With this 2.1mm DC Barrel Jack to Alligator Clips cable you can easily turn a wall adapter into a power supply! A high quality molded 2.1mm DC barrel jack is brought out to red (center positive) & black (ring negative) alligator clips. Works with most wall adapters. Good for 2-3 Amps and up to 24VDC.

        2.1mm DC Barrel Plug to Alligator Clips 2.1mm, dc, jack, barrel, plug, alligator, clips, power, cord, testing
        AF-1329
        Price: $1.95 In Stock
        Item #: AF-1329 -

          This 2.1mm DC Barrel Plug to Alligator Clips cable can turn any battery pack into a power supply in a snap! A high quality molded 2.1mm DC barrel plug is brought out to red (center positive) & black (ring negative) alligator clips. Good for 2-3 Amps of current, up to 24VDC. 2.1mm is near standard for electronics, and fits the Geekduino splendidly.

          4 Pin Sensor Squid 300m 4 pin, sensor, cable, squid, data, 300m, jumper, breakout
          CBL-SQUID4P
          Price: $4.95 In Stock
          Item #: CBL-SQUID4P -

            Sometimes you need to hook a serial/I2C device directly to your Arduino, or minimize the mess of jumper wires on your breadboard. These 4 Pin Sensor Squid 300m cables will help you do just that! On one end, you have a standard 4-pin connector (.1"/2.54mm pitch), and on the other end you have 4 single female jumper wires. You can easily position each cable exactly where you need it. Each cable is 300m in length. Comes in pack of 10 squid cables. Pair these cables with 2-pin couplers to adapt...

            6 USB Cable Extension 6, ft, foot, feet, USB, Cable, Extension, white, gold
            CBL-USBMTF-WHT
            Price: $4.95 In Stock
            Item #: CBL-USBMTF-WHT -

              Need to plug in a USB device, but it's just out of reach? Have a short USB cable with a proprietary connector? The 6' USB Extension cable is what you need! This cable has a standard USB A male connector on one end, and a standard USB A female connector on the other, allowing you to extend the reach of virtually any USB cable in your arsenal.

              6v 3a UBEC 2-5S Lipoly (6-32v) 6v, 3a, UBEC, 2-5S, Lipoly, 6-32v, voltage, regulator
              HK-UBEC6V3A
              Price: $6.95 In Stock
              Item #: HK-UBEC6V3A -

                A BEC (battery elimination circuit) is a great tool for getting a lower voltage from a higher voltage system. For example, say you needed 6v to drive a RobotGeek servo on your 11.1v PhantomX Hexapod , but you didn't want to add a secondary battery just for the 6v servo. Simply plug this BEC into your Hexapod's battery and you'll get a stable 6v 3A power supply. The 6v 3a UBEC 2-5S Lipoly (6-32v) is a small and lightweight UBEC, featuring a High efficiency switch mode design that provides...

                Alligator Clip with Pigtail (4 Pack) Alligator Clip with Pigtail, pin header, breadboard, prototyping
                SF-CAB-13191
                Price: $2.95 In Stock
                Item #: SF-CAB-13191 -

                  This is a 4 pack of wires that are pre-terminated with an alligator clip on one end and a hookup pigtail on the other. Alligator clips are a staple part for any workbench and with these cables you will be able to easily incorporate those clips into a breadboard, development platform, or anything else that you would normally be able to attach a hookup wire to. Each Alligator Clip with Pigtail cable has a wire length of 30cm (that’s a little less than 1ft) and a male pin that easily inserts into...

                  Alligator Test Leads - Multicolored (10 Pack) Alligator Test Leads, Multicolored, alligator clips, prototyping, crocodile clips
                  SF-PRT-12978
                  Price: $2.95 In Stock
                  Item #: SF-PRT-12978 -

                    Alligator clips (or Crocodile clips, if you prefer) are likely to be the most useful thing on your workbench besides the workbench itself. Whether you’re just trying to make a few quick connections to test your circuit or having trouble making your multimeter leads stay where you need them, these spring-loaded clips are a workshop must-have. Each lead in this pack of tern is 50cm long with a rubber shrouded alligator clip on each end. There are five different colors, you get two each of: red,...

                    Cold 2-Wire Splice (UY) - 10 pack cold, wire, splice, uy, crimp
                    AF-1496
                    Price: $2.95 In Stock
                    Item #: AF-1496 -

                      Get connected quickly with a Cold 2-Wire Splice (UY). These little wonders bite into any 22-26 AWG solid core wire with a quick squeeze from some parallel-jaw or slip joint pliers, making a solid butt splice connection. Though not waterproof, the splices contain silicone jelly to keep the cold splice from oxidizing.

                      Cold Splice Wire Tap (UB) - 10 pack cold, wire, splice, ub, crimp
                      AF-1494
                      Price: $2.95 In Stock
                      Item #: AF-1494 -

                        Get connected quickly with a Cold Splice Wire Tap (UB). These little wonders bite into any 22-26 AWG solid core wires with a quick squeeze from some parallel-jaw or slip joint pliers, making a solid 3-way splice connection. Though not waterproof, the splices contain silicone jelly to keep the cold splice from oxidizing.

                        Screwdriver Magnetizer / Demagnetizer Screwdriver, Magnetizer, Demagnetizer
                        SS-114990066
                        Price: $5.90 In Stock
                        Item #: SS-114990066 -

                          The Screwdriver Magnetizer / Demagnetizer is aptly named. Quickly and easily magnetize small tools so they attract screws or nuts for easily starting and removing. Insert a screwdriver or nutdriver into the hole , pull it out and it's magnetized!

                          USB Charger Doctor - In-line Voltage and Current Meter usb, charger, doctor, voltage, current, meter
                          AF-1852
                          Price: $7.50 In Stock
                          Item #: AF-1852 -

                            The USB Charger Doctor is a handy tool that measures the working voltage and current output for any USB port and project. Plug the Doctor between a USB port and your USB device, and it will check the current draw with a 0.05 ohm resistor in line with the power pin. Data lines pass through as normal. You can use this device from 3.5-7VDC input voltage (although most USB devices tend to hover around 4.75 to 5.25) and up to 3A of current. It flips between voltage and current readouts roughly...

                            Sparkfun Cerberus USB Cable Sparkfun Cerberus USB Cable, Sparkfun, Cerberus, USB, Cable, Robot, Data, mini, micro
                            SF-CAB-12016
                            Price: $5.95 In Stock
                            Item #: SF-CAB-12016 -

                              You are in the middle of working on your latest robot, when you need to program a new board you just got in. You dig through your bin of USB cables only to find that you have hundreds that have the wrong end, and exactly zero that have the end you're looking for. As luck would have it, you remember that you ordered the Sparkfun Cerberus USB Cable! With this cable, you will always have the right connection. The Cerberus USB Cable has the standard A-type connector, which you can plug into your...

                              Phidgets 12 foot Sensor Cable Phidgets 12 foot Sensor Cable, Phidget 12 foot Sensor Cable
                              PH-3004
                              Price: $3.00 In Stock
                              Item #: PH-3004 -

                                This is a 12-foot, 3-pin cable for connecting sensors to the analog inputs on the Phidgets 8/8/8 Interface Kit. This product is part of the Phidgets family! Phidgets are an easy to use set of USB-based building blocks for low cost sensing and control from your PC. A wide array of sensors, I/O devices, and controllers are available. To view the entire Phidgets product line, follow this link. Getting Started with Phidgets Phidgets Documentation: Manuals, data sheets, and tutorials for Phidgets...

                                USB A Male to Mini B (5P) M - 6ft
                                CBL-USBA2MINI
                                Price: $4.95 In Stock
                                Item #: CBL-USBA2MINI -

                                  Description This USB A plug to Mini 5 pin (one ID Pin) plug is designed for USB peripherals such as cellular phones, digital devices or PDA. Introduction: With much smaller than existing USB connectors, our 5 pin (one ID Pin) provides reliable host-to-peripherals connectivity for portable/hand-help PC architecture, cellular phones and other digital devices, such as, DSC and PDA. This product is fully compliant with USB 1.1 Standard Specification.

                                  Variable Power Supply 15-24V 4.5A (2.1mm Jack) Variable Power Supply 15-24VDC 4.5A - US
                                  POW-Variable
                                  Price: $24.95 In Stock
                                  Item #: POW-Variable -

                                    Variable Power Supply for general project use. North American Style Plug 15-24VDC 4.5A - US Center Positive Polarity, 5.5x2.1MM PS - You might want one of these too.

                                    6 Inch Digital Calipers in box
                                    SF-TOL-10997
                                    Price: $14.95 In Stock
                                    Item #: SF-TOL-10997 -

                                      6th Century BC: One of the earliest known calipers is lost on an Italian coast, to be found centuries later. 1851: Joseph R. Brown invents the modern vernier caliper. Today: You can own the next evolution in calipers, the Digital Caliper Whether you're measuring a component to get just the right fit in your project box, or you're trying to replicate a complex widget with your 3D printer, you'll need a trusty set of calipers by your side. These calipers even have a data out! This is great for...

                                      Adjustable Breadboard Power Supply Adjustable, Breadboard, Power Supply, arduino, freeduino
                                      SS-TOL123D3P
                                      Price: $15.37 In Stock
                                      Item #: SS-TOL123D3P -

                                        Another breadboard power supply designed by Seeed Studio. it can directly takes power from DC wall wart and outputs a selectable 5V or 3.3V regulated voltage.  Compared to other breadboard power supply designs; this one provides mini-USB port like the seeeduino, you can toggle the switch and select your power source. (USB or dc jack). We also used JST-2pin power jack, the one as on Seeeduino.   With this board, you can send power to both power lane of the breadboard, and each side has a on/off...

                                        Arduino Project Box Arduino, Project, Box, Duemilanove, Diecimila, Arduino Board, Arduino Kit, Arduino Diecimila USB IO Board, Arduino IO Board, Arduino Diecimila, Arduino Diecimila Board
                                        MG-A000009
                                        Price: $11.95 In Stock
                                        Item #: MG-A000009 -

                                          What we have here is a (flame retardant) Arduino Project Box that allows you to safely enclose your Arduino + Shield projects and then set them on fire. Just kidding, please don't. But seriously! Rob your Arduino projects of their nudist free spirit attitudes and put some clothes on them, dang hippies. This enclosure can fit pretty much all Arduino and Arduino Mega models, as well as a majority of shields. It has specifically designed removable ports for use with the Arduino Ethernet shield....

                                          Plastic Project Box and Mouting Hardware arduino project box, arduino box, arduino weather proof box, arduino water proof box, water proof arduino box, weather proof arduino box
                                          ASM-PRBOX
                                          Price: $14.95 Back Order
                                          Item #: ASM-PRBOX -

                                            The Project Box for Arduino is a great starter enclosure for your Arduino. This waterproof box can be used for logging purposes, or you can drill/paint/cut apart the box to suit whatever your needs are! A special mounting plate allows you to mount your Arduino and a shield in a variety of orientations with ease.

                                            Robot Geek Sensor Cable Pack robotgeek, robotgeek sensor pack, robotgeek sensor cable pack, robotgeek cable pack, servo wire, 2 pin jumpers, sensor squid, pin couplers, jr female, y cable, variety pack
                                            RG-SPACK
                                            Price: $34.95 In Stock
                                            Item #: RG-SPACK -

                                              The Robot Geek Sensor Cable Pack will hook you up with all your sensor needs and beyond. This variety cable pack includes:3x 3 Pin Female to Female Y Cable1x 32 Foot Standard Servo Wire20x 3 Pin Sensor Cable10x 2 Pin Dual-Female Jumper Wires (300mm)10x Sensor Squids25x 2-Pin Couplers25x 3-Pin Couplers ...

                                              Squid Cable
                                              CBL-SQUID
                                              Price: $4.95 In Stock
                                              Item #: CBL-SQUID -

                                                Sometimes you need to hook a servo or a sensor directly to your Arduino, or minimize the mess of jumper wires on your breadboard. These Squid Sensor Cables - 10 pack will help you do just that! On one end, you have a standard 3-pin connector (.1"/2.54mm pitch), and on the other end you have 3 single female jumper wires. You can easily position each cable exactly where you need it. and are 200mm in length. Add some 3-Pin Couplers to attach these cables directly to a servo or your arduino. These...

                                                USB 2 Serial Converter Front View
                                                MG-A000059
                                                Price: $13.75 In Stock
                                                Item #: MG-A000059 -

                                                  The original Arduino board has spawned dozens of variations and from the Arduino Mini to the Arduino Lilypad, there is a huge selection to choose from. But not all of these boards have a direct USB connection, leaving it up to you to figure out the best way to connect your new board to your computer. That's where the USB 2 Serial Converter comes in. This board converts a USB connection into a 5 volt Serial TX and RX that you can connect straight to the Arduino Mini, Arduino Ethernet or other...

                                                  12v10a Power Supply 12v10a Power Supply
                                                  POW-12v10A
                                                  Price: $19.95 In Stock
                                                  Item #: POW-12v10A -

                                                    12VDC, 10 Amp Power Supply for general project use.Center Positive Polarity, 5.5x2.1MM barrel jack.

                                                    150mm Jumper Wires F/F (Set of 10)
                                                    AC-200-PRT08430
                                                    Price: $3.95 In Stock
                                                    Item #: AC-200-PRT08430 -

                                                      These Jumper Wires F/F (Set of 10) are great for connecting male headers from one board to another. Combine them with Male Jumpers to make even longer cables! These jumpers will fit neatly into a .1" header, so they're great for bread boards. Each pack of 10 comes with cables in 5 colors. Each cable is 150mm long

                                                      7v5A Power Supply
                                                      POW-7v5A
                                                      Price: $11.95 In Stock
                                                      Item #: POW-7v5A -

                                                        7VDC, 5 Amp Power Supply for general project use. Center Positive Polarity, 5.5x2.1MM barrel jack.

                                                        Barrel Jack Male Pigtail Lead 2.1*5.5*12mm barrel jack male, pigtail lead, power cable, cable, pigtail power,
                                                        CBL-PIGTAIL
                                                        Price: $2.95 In Stock
                                                        Item #: CBL-PIGTAIL -

                                                          The Barrel Jack Male Pigtail Lead 2.1*5.5*12mm is the perfect companion to any 2.1*5.5mm female power jack. Whether you need to hook up to an Arduino/Seeduino Board, a Female Pigtail Lead or the AX/MX Power Hub, this cable has you covered. The tail is 10" long and splits easily.

                                                          Electronic Brick - Fully Buckled 3 Wire Cable - 5 Pack
                                                          SEEED-ELB111C5M
                                                          Price: $4.99 In Stock
                                                          Item #: SEEED-ELB111C5M -

                                                            5 pack of fully buckled 3 wire cables for the Electronic Brick family of products.

                                                            Electronic Brick - Fully Buckled 4 Wire Cable - 5 pack
                                                            SS-ELB130E3O
                                                            Price: $4.99 In Stock
                                                            Item #: SS-ELB130E3O -

                                                              5 pack of fully buckled 4 wire cables for the Electronic Brick family of products.

                                                              Electronic Brick - Half Buckled 3 Wire Cable - 5 Pack
                                                              SS-ELB128E4M
                                                              Price: $4.99 Back Order
                                                              Item #: SS-ELB128E4M -

                                                                5 pack of half buckled 3 wire cables for the Electronic Brick family of products.

                                                                Jumper Wires - Connected 6" (M/F, 20 pack)
                                                                SF-PRT-12794
                                                                Price: $1.95 In Stock
                                                                Item #: SF-PRT-12794 -

                                                                  These are 6" long jumper wires terminated as male to female. Use these to jumper from any male or female header on any board. Multiple jumpers can be connected next to one another on a 0.1" header. Comes in one pack of 20 jumpers (colors shown). Each group of jumpers are connected to each other and can either be pulled apart in any quantity (from 1-20, of course) or kept whole based on you needs. These jumper wires can be used for pretty much everything! They work great with breadboards,...

                                                                  Pin Headers Experimental Pack Pin Headers Experimental Pack
                                                                  SS-STR131B2P
                                                                  Price: $7.95 In Stock
                                                                  Item #: SS-STR131B2P -

                                                                    This pack included 41 parts of most commonly used Pin-headers. Perfect for your breadboard/protoboard project. Parts List Female 1*40 2.54mm pin headers X1 Male 1*40 2.54mm pin headers X2 Male 1*40 2.54mm pin headers, stackable Male 1*40 2.54mm pin headers, bend on board X1 Male 1*40 2.54mm pin headers, bend above board X1 Female 1*8 2.54mm pin headers, bend on board X3 Female 1*6 2.54mm pin headers, bend on board X3 Female 1*8 2.54mm pin headers, stackable X3 Female 1*6 2.54mm pin headers,...

                                                                    Probe jumper wire – 8pcs
                                                                    SS-CAB01101M
                                                                    Price: $4.00 In Stock
                                                                    Item #: SS-CAB01101M -

                                                                      This is a 300mm jumper wire with probe, it is easy for connecting two point.

                                                                      RobotGeek 150mm 3-pin Sensor Cable 10 pack
                                                                      CBL-JRFEM150
                                                                      Price: $4.95 In Stock
                                                                      Item #: CBL-JRFEM150 -

                                                                        RobotGeek Sensor Cables are for use with all RobotGeek sensors, shields, servos, and output devices. These cables are .1"(2.54mm) pitch and are 150mm in length with color coded wires. Add some 3-Pin Couplers to connect cables together for extension cables. These cables are also compatible with Phidgets Sensors and Electronic Brick Sensors, though they do not have the plastic buckle like traditional Phidgets/Electronic Brick Cables. ...

                                                                        Turbo Fuse Super Glue 10ml
                                                                        PL-15180
                                                                        Price: $9.95 In Stock
                                                                        Item #: PL-15180 -

                                                                          Turbo Fuse Super Glue is a standard super glue in a thicker viscosity. It is metal and plastic safe and recommended for use with high vibration robots when you really need a lot of holding strength to keep your nuts and bolts in place.This is a 10ml bottle intended for larger projects. You can find the smaller 2ml vial here.

                                                                          Turbo Fuse Super Glue 2ml
                                                                          PL-04180
                                                                          Price: $3.95 In Stock
                                                                          Item #: PL-04180 -

                                                                            Turbo Fuse Super Glue is a standard super glue in a thicker viscosity. It is metal and plastic safe and recommended for use with high vibration robots when you really need a lot of holding strength to keep your nuts and bolts in place.This is a 2ml vial intended for smaller projects. You can find the 10ml bottle here.

                                                                            Turbo-Fuse Blue Plastic Safe Thread Locker 2ml Turbo-Fuse Blue Plastic Safe Thread Locker
                                                                            PL-20001
                                                                            Price: $3.95 In Stock
                                                                            Item #: PL-20001 -

                                                                              Turbo Lock Blue is a plastic safe thread locker. This is the thread locker that we include in all our kits. This thread locker is a medium to strong bond and works on both plastic and metal without causing any plastic weakness. Turbo Lock Blue creates a good strong bond to hold nuts, bolts, and standoffs in place. Yet it can still be broken free with regular tools if you need to take something apart again. Highly recommended for any robotics project that has a lot of shake or movement...

                                                                              Turbo-Lock Blue Thread 2ml
                                                                              11-001
                                                                              Price: $2.95 In Stock
                                                                              Item #: 11-001 -

                                                                                Turbo Lock Anaerobic Thread Locker (Blue) (Medium Strength, Removable) Robots tend to jiggle and vibrate a lot. When they do this long enough their nuts and bolts shed like an Alabama dog in the spring. It is highly recommended to use a thread locker to prevent this from happening. Turbo Lock does a great job keeping your robots together. See our pro tip below about how to easily use it during assembly. This is a 2ml vial. The larger 10ml bottle is here. PLEASE NOTE: This version of Turbo Lock...

                                                                                Wireless Charging Module - 5V/1A
                                                                                SS-106990017
                                                                                Price: $8.50 In Stock
                                                                                Item #: SS-106990017 -

                                                                                  The Wireless Charging Module can be applied in electronic equipments in common use for close wireless charging or power supply. Consisted of a transmitter and insulation coil, it could serve as a replacement for the Wireless Power Supply with stable 5V output voltage and maximum 1.2A output current. Its small size and insulation coil is more suitable for using in wireless project. Most important of all, you can get the output 5v and 1A with 5v input voltage. High efficiency stabilized power...

                                                                                  GP2D12 - Sharp IR Sensor to Servo Cable
                                                                                  RC-IR_Cable
                                                                                  Price: $1.95 In Stock
                                                                                  Item #: RC-IR_Cable -

                                                                                    This cable adapts from the JST connector found on the Sharp IR sensors to a standard 3-pin servo-style connector.  This is compatible with many robot controller boards, such as those used in the Robonova and KHR humanoids.

                                                                                    150mm Jumper Wires M/M (Set of 10)
                                                                                    AC-200-PRT08431
                                                                                    Price: $3.95 In Stock
                                                                                    Item #: AC-200-PRT08431 -

                                                                                      These Jumper Wires M/M (Set of 10) are great for connecting female headers from one board to another. Combine them with FeMale Jumpers to make even longer cables! These jumpers will fit neatly into a .1" header, so they're great for bread boards. Each pack of 10 comes with cables in 5 colors. Each cable is 150mm long

                                                                                      2 Pin Dual-Female Jumper Wire - 300mm - 10pcs pack
                                                                                      CBL-S-CAB103C4O
                                                                                      Price: $4.50 In Stock
                                                                                      Item #: CBL-S-CAB103C4O -

                                                                                        These 2 Pin Dual-Female Jumper Wire - 300mm - 10pcs pack are perfect for prototyping. Use them to run power from one breadboard rail to another, or use multiples to connect signals from one board to another. Each pack comes with 10 cables and each cable is 300mm long. The .1" pitch is great for standard breadboards.

                                                                                        2.1/5.5mm Jack to 2.5/5.5mm Plug Adapter 2.1/5.5mm Jack to 2.5/5.5mm Plug Adapter
                                                                                        POW-plug-adapter
                                                                                        Price: $3.95 In Stock
                                                                                        Item #: POW-plug-adapter -

                                                                                          This is an adapter that converts a 2.1/5.5mm Jack into a 2.5/5.5mm Plug. This will adapt our 2.1/5.5mm plug power supplies into a 2.5/5.5mm plug.

                                                                                          2.1mm DC Jack to JST
                                                                                          SS-ARD101C4O
                                                                                          Price: $2.95 In Stock
                                                                                          Item #: SS-ARD101C4O -

                                                                                            This is a 2.1mm to JST adapter for powering the Seeeduino microcontrollers directly from one of our 6v 2A power supplies.

                                                                                            Breadboard Jumper Wire - 70pcs pack Breadboard, Jumper, Wire, cable, arduino, freeduino, seeeduino
                                                                                            CBL-JW-003
                                                                                            Price: $7.99 In Stock
                                                                                            Item #: CBL-JW-003 -

                                                                                              Anyone who has ever worked with a bread board can tell you that the wiring can get very complicated very quickly. Keeping your wires color coded and solidly connected to your board can mean the difference between a sucessful circuit and having to tear everything down ans start from scratch. That's where the Breadboard Jumper Wire Pack comes in. These wires come in an assortment of colors and lengths and are designed for use with breadboards. The insulated wire is stranded, making it extremly...

                                                                                              JST 2 Pin Power Connector
                                                                                              SS-ARD110C4B
                                                                                              Price: $2.95 In Stock
                                                                                              Item #: SS-ARD110C4B -

                                                                                                JST 2 Pin power connector Use for making custom power supplies for the Seeeduino Boards Length:100mm

                                                                                                Premium Jumper Wires 140 pcs/box
                                                                                                CBL-JW-001
                                                                                                Price: $9.50 In Stock
                                                                                                Item #: CBL-JW-001 -

                                                                                                  Keeping the wiring on your breadboard neat and clean is a must for any large scale protyping endeavor. That's where the Premium Jumper Wire Box comes in. Don't waste your precious time cutting and bending wires, just pull out the appropriatley sized one at a momen't notice! This set provides 10 different lengths varying from 3mm-125mm, in a variety of colors.