Item #: ASM-PIXY-CAM -
Vision Processing is a lot of work - even low resolution camera can output lots of data, and parsing through that data can be a lot of work. But don't worry, the CMUcam5 Pixy is here! The Pixy is a vision sensor that can quickly track colored objects and report back their X/Y position to your Arduino or other microcontroller. The Arduino can then take that data and control motors and other devices based on the position of the tracked objects. Add the Pixy to one of our Crawlers, Rovers,Turrets...
Item #: CBL-USB2MICRO -
This 6ft Micro USB Cable is perfect for powering and programming controllers like the RobotGeek Geekduino
Item #: CBL-USBA2B -
It is a standard USB A to B cable. It is 6 feet long. It has gold plated connectors. Not much else to say. Buy one if you need it. Or don't. It won't hurt our feelings honestly.
Item #: MG-A000066 -
The Arduino Uno R3 is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Uno differs from all...
Item #: RG-GEEKDUINO -
The Geekduino is the new Arduino Compatible board from RobotGeek! This board goes into every RobotGeek Robot Kit and is the perfect microcontroller for your next robotic project! The Geekduino uses the ubiquitous Micro USB port to power and program the board. The Geekduino can also be powered via the ultra low-profile flat DC power jack. A series of switches allows you to toggle on/off the Geekduino's FTDI reset (handy for software projects) as well as change the operating voltage of the...
Item #: TI-TG-02B-DC12B -
If you are looking for an Arduino Pump the RobotGeek Large Liquid Pump is a great solution. This pump is self priming, quiet, food safe, and can move up to 2 liters per minute. To use this for an Arduino Pump project all you need is a RobotGeek Relay and seperate power supply. The pump will work with standard aquarium tubing. The fit is a little tight, but the tubing will go on. We recommend picking up some of our 3.5mm food safe silicone tubing which fits great and goes on easier! Recommended...
Item #: RG-SMPUMP -
If you are looking for an Arduino Pump the RobotGeek small liquid and air pump is a great solution. This pump is self priming and food safe so it can be used for projects involving plant watering, suction, drainage, drink dispensing, barbots, and more. To use this for an Arduino Pump project all you need is a RobotGeek Relay and seperate power supply. The pump can operate at either 6 or 12 volts and packs a punch in a small package! Recommended Arduino Pump Tutorials: Arduino ShotBot Project...
Item #: HW-WVALVE -
If you are looking for an Arduino solenoid valve the RobotGeek liquid solenoid valve is a perfect solution. Compact, food safe, and with mounting holes make it a great fit for DIY projects of all kinds. The Solenoid Valve is a great companion to the Large DC Liquid Pump and the Small DC Liquid Pump. When building pumping projects sometimes it is necessary to add a valve to stop either liquid back draw or unwanted flow. When using diaphram pumps if your liquid supply is higher than your pouring...
Item #: MG-A000065 -
The Wireless SD Shield provides a 3.3v regulated Digi Xbee slot for easy wireless connectivity, a uSD (micro Secure Digital) slot for onboard storage capabilities, and a compact prototyping board area for custom additions. Transmission LED indicator lights, a reset button, and serial select switch are also available for your convenience. Passthrough headers allow for additional Shields to be stacked on top.More information available soon!
Item #: KIT-ARD-BE -
The Basic Experimenters Kit for Arduino contains many of the most popular accessories for DIY projects to get you up and running fast. This handy experimenters kits is great for those that want to learn about physical computing on a basic hardware component level! Tinkerers will get to interact with the Arduino microcontroller on a basic circuitry level, creating connections from I/O pins to raw sensors, resistors, and capacitors. The kit contains the essentials: an Arduino Uno, breadboard,...
Item #: KIT-ARD-EB -
The Electronic Brick Starter Kit for Arduino is a modular physical computing kit compatible with the Arduino platform. It includes an Arduino Uno, 6v regulated power supply, and an Electronic Brick Chassis for interfacing sensors, and a variety of modular sensors and output devices. You can build many interesting projects even without soldering skills, making this kit a great starting point for beginners looking to learn more about microcontrollers, programming, and electronic sensory! Arduino...
Item #: SS-ELB00100M -
Description GROVE is an open modular toolset, designed to minimize the difficulty of fundamental electronic engineering. It is formed by functional modules Grove and interface board STEM. Each Grove has unified 4pin interface and standardized jigsaw shape for easy combination. They can work with major existing development platform (like Arduino and compatible boards, beagle board, Xbee, and etc) via STEMs. Pack list Base Shield Grove - LCD RGB Backlight Grove - Smart Relay Grove - Buzzer Grove...
Item #: KIT-ARD-GR -
Description The Grove Starter Kit for Arduino is a modular building-block system for physical computing. Great for teaching, learning, rapid prototyping, and also perfect for projects around the house! Plug in various sensor modules, output devices, and displays using a convenient unified 4 pin plug interface. GROVE is an open modular toolset, designed to minimize the difficulty of fundamental electronic engineering. It is formed by functional modules Grove and interface board. Each Grove...
Item #: MG-T020040 -
Extension Sensor Shield for Arduino Mega series. Easily connect more than 25 sensors, actuators and serial devices to the main board. The shield has a built in voltage regulator in order to supply extra power to the digital IO in order to fulfill the power needs of a fully populated platform.
Item #: KIT-ARD-XB -
Take your next Arduino project on the road! The Xbee Wireless Kit for Arduino is the perfect bundle to get started with wirelessly connected physical computing and data-logging. Need to get sensor input from a remote location to your PC? This kit employs the use of Xbee wireless modules to create a wireless serial link between your PC and Arduino. Load your Arduino up with sensors and a sketch, and have it sending and receveing packets in no time! This kit utilizes the new Wireless SD Shield,...
Item #: MG-K000007 -
Arduino is an open source electronic prototyping platform. With a combination of the Arduino IDE (software) and the line of Arduino Microcontrollers (hardware) you can design, build and program electronic systems to accomplish almost any task! Whether you just need to blink some LEDs, control motors, or power your latest invention, the Arduino Platform will help you get to the finish line. If you're looking for a one-stop, highly structured way to get started in the Arduino World, then check...
Item #: SS-WLS01311P -
Have you ever wanted to hook up your robot to your iOS device? Now you can utilize Bluetooth 4.0 Low Energy (BLE) technology in your robot with the BLE Mini. The BLE Mini requires only a serial port for communication so it supports all major development platforms that have UART interface including Arduino, ArbotiX-M Robocontroller, Geekduino, Raspberry Pi, etc. In addition, you are given access to all Ti's CC2540 I/O pins and the ability to upload firmware via USB, making the BLE Mini an ideal...
Item #: SF-DEV12646 -
Is the Arduino Uno's hardware just not cutting it? Do you need a more powerful platform, but you're not ready to move away from the Arduino IDE? Then the Teensy is the perfect ARM based micorcontroller for your next robot project. The Teensy 3.1 is a complete USB-based microcontroller development system and is as versitile as it is powerful. A custom Teensy installer and bridge application will easily allow you to write sketches for the Teensy and load them on to the Teensy. All programming is...
Item #: MG-A000062 -
The Arduino Due represents the next generation of Arduino hardware. This board is based on the Atmel SAM3X8E ARM Cortex-M3 CPU, a 32-bit, 84 MHz microcontroller. This board will give you 96 Kbytes of SRAM, as well as 512 Kbytes of flash memory to hold store your code. The Due even has a DMA controller to help relieve the processor of memory intensive tasks. The Arduino Due has some amazing capabilities. It has 54 Digital I/O pins, 12 of which can be used for PWM. The Due can use any of these...
Item #: MG-A000057 -
The Arduino Uno is a great place to start in the Arduino World, but sometimes you need a few extra features to get your project up and running. The Arduino Leonardo , a variant of the Uno, is just the board you need! So what's so special about the Leonardo? The Leonardo can easily act as USB HID(Human Interface Device) such as a Keyboard or Mouse, opening a whole class of projects for you to explore with yout Arduino. This is accomlished by using the ATmega32u4, a microcontroller that acts...
Item #: MG-A000067 -
Overview The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter...
Item #: MG-A000063 -
Overview The Arduino ADK is a microcontroller board based on the ATmega2560 (datasheet). It has a USB host interface to connect with Android based phones, based on the MAX3421e IC. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. The ADK is based on the Mega 2560. Similar to the Mega 2560 and Uno, it features an...
Item #: SF-DEV-09219 -
It's blue! It's skinny! It's the Arduino Pro! SparkFun's minimal design approach to Arduino. This is a 5V Arduino running the 16MHz bootloader (select 'Arduino Duemilanove w/ 328' within the Arduino software). The power switch was moved to the side of the board (good idea Limor!) to allow control when a shield is attached. Please note: The right-angle power switch is fragile. We're working on making the switch stronger. For now, please be gentle. Arduino Pro does not come with connectors...
Item #: SF-DEV-09218 -
It's blue! It's thin (0.8mm)! It's the Arduino Pro Mini! SparkFun's minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader (select 'Arduino Duemilanove w/ 328' within the Arduino software). Arduino Pro Mini does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We recommend first time Arduino users start with the Duemilanove. It's a great board that will get you up and running quickly. The Arduino...
Item #: SL-Netduino -
Software, meet hardware. Netduino is an open source electronics platform using the .NET Micro Framework. Featuring a 32-bit microcontroller and a rich development environment. Suitable for engineers and hobbyists alike. Code. Debug. Repeat. .NET Micro Framework combines the ease of high-level coding and the features of microcontrollers. Enjoy event-based programming, multi-threading, line-by-line debugging, breakpoints and more. Design files included. Netduino is an open source electronics...
Item #: KIT-RG-GEEKSHIELD -
Everything you need to be up and running with a Geekduino and Sensor shield I/O break out board to mount to your projects. GeekduinoSensor Shield10 Robotgeek sensor cablesDuino Mounting PlateThe Robotgeek Sensor Shield breaks out the digital and analog pins into easy to use 3-pin connectors. Each connector supplies 5 volts, ground, and a signal pin. These connectors can easily be connected to RobotGeek Sensors as well as a wide variety of sensors, actuators and output...
Item #: ASM-RG-LCD -
The RobotGeek LCD is a fast and easy way to add text output to your projects. The enclosure can float freely on your desk or be mounted to projects and Workbenches. The bottom has the standard RobotGeek 1cm X 1cm grid making all RobotGeek products compatible with each other.
Item #: SS-ARD128D2P -
Seeeduino v3.0 328P is an Arduino-compatible board. Its design is based on Duemilanove scheme, 100% compatible to existing programs, shields and IDEs. On the hardware however, many changes have been made to improve the flexibility and user experience. Arduino is an open-source electronics prototyping platform based on flexible, easy-to-use hardware and software. It's intended for artists, designers, hobbyists, and anyone interested in creating interactive objects or environments. ...
Item #: SF-DEV-07914 -
Description: Riding on the waves of the very popular Arduino USB board is this small prototyping shield. Originally spawned with collaboration between the folks at SFE and ITP @ NYU, the Protoshield mates with the Arduino USB board and gives the user a small soldering area, two general LEDs, access to a BlueSMiRF socket, a general pushbutton switch, and most important of all - the Arduino reset switch is brought to the top level. This comes in kit form and must be soldered together by the end...
Item #: MG-A000072 -
The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100ethernet chip (datasheet). The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps...
Item #: MG-A000079 -
Are you ready to start controlling the universe with your Arduino? Or at least some beefier motors? Built around the L298 chip, the Arduino Motor Shield is a dual full-bridge driver. This shield is designed to drive inductive loads such as relays, solenoids, DC and stepping motors – anything your poor little Arduino would burn up on if it tried to drive them itself. You’ll be able to drive two motors via 8 pins on your Arduino. Each channel will allow you to control speed and direction, as...
Item #: SF-DEV-09815 -
This is a motor shield for Arduino that will control two DC motors. Based on the L298 H-bridge, the Ardumoto can drive up to 2 amps per channel. The board takes its power from the same Vin line as the Arduino board, includes blue and yellow LEDs to indicate active direction, and all driver lines are diode protected from back EMF. Control for motor attached to OUT1/2 is connected to digital line 12 (direction A) and digital line 10 (PWM A). Control for motor attached to OUT3/4 is...
Item #: SS-SLD63030P -
The Bluetooth Shield integrates a Serial Bluetooth module. It can be easily used with Arduino/Seeedstudio for transparent wireless serial communication. You can choose two pins from Arduino D0 to D7 as Software Serial Ports to communicate with Bluetooth Shield (D0 and D1 is Hardware Serial Port). The shield also has two Grove connectors (one is Digital, the other is Analog) for you to install Grove modules. Features Seeeduino/Arduino compatible Up to10m communication distance in house without...
Item #: SS-ARD105B1P -
The Danger Shield is an add-on for the Arduino & Freeduino micro controller boards. It contains a variety of fun and useful electronic circuits that you can use to do fun and useful things. It is a fully self-contained shield. You plug it into your Arduino, and you can immediately start using it. No extra things to hook up, no external components. Just a really rad board ready to rock. Note: This is a kit- Assembly & Soldering is required. Some of the features of the board are: 3...
Item #: SS-SLD01106P -
The EL Shield kit is an easy to use shield to control electroluminescent (EL) devices (such as EL wire) with either an Arduino or Seeeduino. The board has 4 outputs so you can control up to 4 devices separately! It can drive EL wires at long as 15 m (49 ft). This shield come without the headers soldered on, so you'll have to attach them before use. If you know how to control an LED, you can control EL devices. The EL Shield makes it that easy! The shield uses pulse-width modulation (PWM), so...
Item #: SS-SLD33149P -
Description The GPRS (General Packet Radio Service) Shield is a new nonvoice value added service that delivers GSM/GPRS 850/900/1800/1900MHz performance for voice, SMS, Data, and Fax in a small form factor and with low power consumption. It is controlled via AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands), and fully compatible with Seeeduino/Arduino and Mega. The GPRS Shield has 12 GPIOs 2 PWMs and 1 ADC(They are all 2V8 logic). Features Quad-Band 850/ 900/ 1800/ 1900 MHz GPRS...
Item #: SS-SLD80256P -
Quickly add motor control to your Arduino or Seeeduino with the Grove Motor Shield! You can use the shield to easily connect 2 brushed DC motors, which makes it great for controlling wheeled platforms like the Budget Bot Chassis. Use the Grove Motor Shield to control motors from 6-15 volts, with up to 2 amps per channel. Easily accessible screw terminals will let you connect your motors and external power. This shield is also great if you're using the Grove sensors, since it has 13 Grove ports...
Item #: SS-SLD12148P -
Check out the latest version of the Grove Sensor Shield! This shield sports a simplified design and additional I2C ports The Grove base shield will allow you to easily connect Grove sensor and output modules to your Arduino or Arduino compatible board. Just connect the Grove Sensor Shield to your Arduino and use a Grove Universal Cable to connect the shield to one of our many Grove Modules. The Grove systemuses 4-pin 2mm header. This allows for up to two digital or analog per cable, enabling...
Item #: SS-INT109B2P -
Every project is better with music! Build your own music player with the music shield. Or use it to give your robot a voice and/or sound effects. The Music Shield is an ipod/iphone dock compatible shield. It can work with Arduino, Seeeduino, Seeeduino Mega and Arduino Mega2560. It is based on the VS1053b and can play variety of music format stored on MicroSD card with Seeed Studio provided Arduino Library. Note: Recording is only supported by Seeeduino Mega and Arduino Mega2560. Documentation...
Item #: MG-E000008 -
If you need a lot of inputs and/or outputs, this is your solution! The Mux (Multiplexer) Shield adds the capacity for up to 48 inputs or outputs on the Arduino and Arduino Mega. Using three Texas Instruments CD74HC4067 Analog Multiplexers, the Mux Shield makes it possible to have 48 analog/digital inputs or digital outputs in many combinations. The Mux Shield comes with 5V and Ground headers so you'll have power available to each input or output and comes with stackable headers installed. The...
Item #: RG-BUZZER -
Get buzzing with this Arduino Buzzer! The RobotGeek Buzzer is an easy way to add audio output to your Arduino. By simply sending a 5v signal to the RobotGeek Buzzer, the device will emit a tone. You can also use the Arduino Tone Function to send different tones to the buzzer. NOTE:some frequencies will work better than others with this piezo buzzer. This Arduino Buzzer has the standard RobotGeek three pin connection so it plugs right into the RobotGeek Sensor Shield to get you up and running...
Item #: RG-JOYSTICK -
If you are looking for a good Arduino Joystick the RobotGeek Joystick is the best choice. We had these joysticks special made two joystick options; the standard mushroom top used in gaming controllers and a tall stick for much greater range of motion. The joystick has the standard RobotGeek three pin connection and plugs right into the RobotGeek Sensor Shield so you can be up and running immediatly. This arduino joystick is self centering and will return to the home position when let go. The...
Item #: RG-LIGHT -
This RobotGeek Light Sensor is an analog sensor that will allow you to measure light from your Arduino or other microcontroller. The more light the sensor detects, the higher the your analog port will detect. Each RobotGeek Light Sensor comes with a dual female-female jumper cable so that you can move the light sensor off the board. This makes placing your sensors easier than ever. You can use this sensor to measure the ambient light in a room, or to measure the relative brightness of...
Item #: RG-PUSHBUTTON -
The RobotGeek Pushbutton is a self-contained Arduino Button board that makes it easy to add a pushbutton to your Arduino Project. This RobotGeek Pushbutton has a built in pull-down resistor, so the signal can be read as a digital input from your Arduino or other microcontroller. This Arduino Button Board has the standard RobotGeek three pin connection so it plugs right into the RobotGeek Sensor Shield to get you up and running immediatly. As with all RobotGeek sensors, the hole mounting...
Item #: RG-RELAY -
Time to step up the voltage with this Arduino Relay Board. The Arduino platform is a great way to control lights, buzzers, displays and more - but what if you have a device that doesn't run on the Arduino's native 5 volts? One simple way to do it is to use the RobotGeek Relay. This little relay board will use a signal from a 5v microcontroller to make a mechanical connection. This connection is physically seprated from the arduino, meaning you can connect devices that have different voltages...
Item #: RG-ROTKNOB -
Do you need Rotation Knobs for your Arduino project? The RobotGeek Knob is good choice! It has the standard RobotGeek three pin connection so it plugs right into the RobotGeek Sensor Shield to get you up and running immediatly. As with all RobotGeek sensors, the hole mounting pattern is on a 1x1 CM grid so they easily mount to the RobotGeek Workbenches or any other RobotGeek kit. Don't forget to pick up RobotGeek Sensor Cables if you need some! ...
Item #: RG-SENSOR -
The Arduino Platform is a great way for learning about electronics and programming, as well as creating microcontoller based projects. But even simple projects can get messy very quickly, leaving you with a pile of wires, breadboards, and components. With the RobotGeek Sensor System, you can put your project on the fast track and get it up and running in no time. The RobotGeek Sensor Shield will fit on any Standard Arduino Compatible board*, and break out the digital and analog pins into easy...
Item #: RG-SLIDER -
The RobotGeek Slider is a great arduino slide potentiometer for projects requiring a linear analog input. The slider has the standard RobotGeek three pin connection and plugs right into the RobotGeek Sensor Shield so you can be up and running immediatly. This arduino slide control is a linear potentiometer, which means you can read it just as you would any other potentiometer/analog sensor. The large handle cap and the smooth action on this slider make it great for all kinds of control panels...