Item #: MG-A000066 -
The Arduino Uno R3 is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Uno differs from all...
Item #: RG-GEEKDUINO -
The Geekduino is the new Arduino Compatible board from RobotGeek! This board goes into every RobotGeek Robot Kit and is the perfect microcontroller for your next robotic project! The Geekduino uses the ubiquitous Micro USB port to power and program the board. The Geekduino can also be powered via the ultra low-profile flat DC power jack. A series of switches allows you to toggle on/off the Geekduino's FTDI reset (handy for software projects) as well as change the operating voltage of the...
Item #: IL-ARBOTIXPRO -
The Arbotix-Pro is a robotics subcontroller based around the STM32F103 Cortex M3 ARM cpu. It has support for both TTL or RS-485 communciation, to control AX, MX, and Dynamixel-PRO actuators from ROBOTIS. Interface to the main CPU of a robot is provided via USB, Xbee, or UART, all of which are on dedicated serial ports and can be used simultaneously for other comms. The Arbotix-Pro ships with a CM-730 compatible firmware, which enables the subcontroller to be recognized as an ID 200 Dynamixel...
Item #: SF-DEV12646 -
Is the Arduino Uno's hardware just not cutting it? Do you need a more powerful platform, but you're not ready to move away from the Arduino IDE? Then the Teensy is the perfect ARM based micorcontroller for your next robot project. The Teensy 3.1 is a complete USB-based microcontroller development system and is as versitile as it is powerful. A custom Teensy installer and bridge application will easily allow you to write sketches for the Teensy and load them on to the Teensy. All programming is...
Item #: MG-A000062 -
The Arduino Due represents the next generation of Arduino hardware. This board is based on the Atmel SAM3X8E ARM Cortex-M3 CPU, a 32-bit, 84 MHz microcontroller. This board will give you 96 Kbytes of SRAM, as well as 512 Kbytes of flash memory to hold store your code. The Due even has a DMA controller to help relieve the processor of memory intensive tasks. The Arduino Due has some amazing capabilities. It has 54 Digital I/O pins, 12 of which can be used for PWM. The Due can use any of these...
Item #: MG-A000057 -
The Arduino Uno is a great place to start in the Arduino World, but sometimes you need a few extra features to get your project up and running. The Arduino Leonardo , a variant of the Uno, is just the board you need! So what's so special about the Leonardo? The Leonardo can easily act as USB HID(Human Interface Device) such as a Keyboard or Mouse, opening a whole class of projects for you to explore with yout Arduino. This is accomlished by using the ATmega32u4, a microcontroller that acts...
Item #: MG-A000067 -
Overview The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter...
Item #: MG-A000063 -
Overview The Arduino ADK is a microcontroller board based on the ATmega2560 (datasheet). It has a USB host interface to connect with Android based phones, based on the MAX3421e IC. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. The ADK is based on the Mega 2560. Similar to the Mega 2560 and Uno, it features an...
Item #: SF-DEV-09219 -
It's blue! It's skinny! It's the Arduino Pro! SparkFun's minimal design approach to Arduino. This is a 5V Arduino running the 16MHz bootloader (select 'Arduino Duemilanove w/ 328' within the Arduino software). The power switch was moved to the side of the board (good idea Limor!) to allow control when a shield is attached. Please note: The right-angle power switch is fragile. We're working on making the switch stronger. For now, please be gentle. Arduino Pro does not come with connectors...
Item #: SF-DEV11113 -
It's blue! It's thin (0.8mm)! It's the Arduino Pro Mini! SparkFun's minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader (select 'Arduino Duemilanove w/ 328' within the Arduino software). Arduino Pro Mini does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We recommend first time Arduino users start with the Duemilanove. It's a great board that will get you up and running quickly. The Arduino...
Item #: SL-Netduino -
Software, meet hardware. Netduino is an open source electronics platform using the .NET Micro Framework. Featuring a 32-bit microcontroller and a rich development environment. Suitable for engineers and hobbyists alike. Code. Debug. Repeat. .NET Micro Framework combines the ease of high-level coding and the features of microcontrollers. Enjoy event-based programming, multi-threading, line-by-line debugging, breakpoints and more. Design files included. Netduino is an open source electronics...
Item #: KIT-RG-GEEKSHIELD -
Everything you need to be up and running with a Geekduino and Sensor shield I/O break out board to mount to your projects. GeekduinoSensor Shield10 Robotgeek sensor cablesDuino Mounting PlateThe Robotgeek Sensor Shield breaks out the digital and analog pins into easy to use 3-pin connectors. Each connector supplies 5 volts, ground, and a signal pin. These connectors can easily be connected to RobotGeek Sensors as well as a wide variety of sensors, actuators and output...
Item #: SS-ARD128D2P -
Seeeduino v3.0 328P is an Arduino-compatible board. Its design is based on Duemilanove scheme, 100% compatible to existing programs, shields and IDEs. On the hardware however, many changes have been made to improve the flexibility and user experience. Arduino is an open-source electronics prototyping platform based on flexible, easy-to-use hardware and software. It's intended for artists, designers, hobbyists, and anyone interested in creating interactive objects or environments. ...
Item #: SS-ARD127D2P -
The Rainbowduino board is an Arduino compatible controller board for driving LEDs. It will drive an 8x8 RGB Led Matrix (Common Anode). Work Modes The Rainbowduino can run in different work modes depending on your needs. Standalone Mode (plug and shine) UART Mode (Send data from your computer to one Rainbowduino.) I2C Mode (Send data from your computer to multiple Rainbowduino’s.) I2C Cascading (PC or Arduino generated frames displayed on multiple Led Matrices.) Features Pairs with 8x8 RGB Led...
Item #: SS-ARD121D2P -
Overview Seeeduino Mega is a microntrolller board based on ATmega1280, derived from Arduino Mega with changes in pursuit for small form factor, flexibility and functionality.It has 70 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with...
Item #: SL-NetduinoBK -
This book is the companion guide to the Netduino Plus. What is the Internet of Things? It's billions of embedded computers, sensors, and actuators all connected online. If you have basic programming skills, you can use these powerful little devices to create a variety of useful systems—such as a device that waters plants when the soil becomes dry. This hands-on guide shows you how to start building your own fun and fascinating projects. Learn to program embedded devices using the .NET Micro...
Item #: SF-DEV-09521 -
The SerIO is a serial interface platform for creating physical computing projects controlled from a computer. The board gives access to 14 digital input and output pins, six analog output pins and eight analog input pins through a serial interface. This allows the creation of physical computing projects wihtout having to modify and code on the hardware platform. Projects that involve the use of analog sensors, buttons, LEDs, buzzers, motors and many more electronic components can be controlled...
Item #: IL-ARBOTIXM -
The ArbotiX-M Robocontroller is at the heart of every Interbotix Robot. This versatile robot controller is an advanced control solution for BIOLOID and DYNAMIXEL based actuators. As an Arduino compatible microcontroller the Arbotix Robocontroller also benefits from a huge open source community of libraries and examples. Since its release in 2010 the Arbotix has quickly become a favorite among builders worldwide from hobby to high level research. The 'M' in ArbotiX-M stands for mini - this new...
Item #: ASM-RG-DUINOMNT -
The Duino Mounting Plate converts the Arduino three hole pattern to the standard Robot Geek hole pattern. All Robot Geek kits, sensors, and components conform to a 1 x 1 centimeter grid making it easy to custom build your projects any way you desire. The Duino Mounting Plate allows you to easily mount and move your Arduino boards anywhere you want on your Robot Geek projects.*NOTE: The Duino Mounting plate does not come with the Geekduino.