Item #: MG-A000065 -
The Wireless SD Shield provides a 3.3v regulated Digi Xbee slot for easy wireless connectivity, a uSD (micro Secure Digital) slot for onboard storage capabilities, and a compact prototyping board area for custom additions. Transmission LED indicator lights, a reset button, and serial select switch are also available for your convenience. Passthrough headers allow for additional Shields to be stacked on top.More information available soon!
Item #: MG-T020040 -
Extension Sensor Shield for Arduino Mega series. Easily connect more than 25 sensors, actuators and serial devices to the main board. The shield has a built in voltage regulator in order to supply extra power to the digital IO in order to fulfill the power needs of a fully populated platform.
Item #: SF-DEV-07914 -
Description: Riding on the waves of the very popular Arduino USB board is this small prototyping shield. Originally spawned with collaboration between the folks at SFE and ITP @ NYU, the Protoshield mates with the Arduino USB board and gives the user a small soldering area, two general LEDs, access to a BlueSMiRF socket, a general pushbutton switch, and most important of all - the Arduino reset switch is brought to the top level. This comes in kit form and must be soldered together by the end...
Item #: MG-A000072 -
The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100ethernet chip (datasheet). The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps...
Item #: MG-A000079 -
Are you ready to start controlling the universe with your Arduino? Or at least some beefier motors? Built around the L298 chip, the Arduino Motor Shield is a dual full-bridge driver. This shield is designed to drive inductive loads such as relays, solenoids, DC and stepping motors – anything your poor little Arduino would burn up on if it tried to drive them itself. You’ll be able to drive two motors via 8 pins on your Arduino. Each channel will allow you to control speed and direction, as...
Item #: SF-DEV-09815 -
This is a motor shield for Arduino that will control two DC motors. Based on the L298 H-bridge, the Ardumoto can drive up to 2 amps per channel. The board takes its power from the same Vin line as the Arduino board, includes blue and yellow LEDs to indicate active direction, and all driver lines are diode protected from back EMF. Control for motor attached to OUT1/2 is connected to digital line 12 (direction A) and digital line 10 (PWM A). Control for motor attached to OUT3/4 is...
Item #: SS-SLD63030P -
The Bluetooth Shield integrates a Serial Bluetooth module. It can be easily used with Arduino/Seeedstudio for transparent wireless serial communication. You can choose two pins from Arduino D0 to D7 as Software Serial Ports to communicate with Bluetooth Shield (D0 and D1 is Hardware Serial Port). The shield also has two Grove connectors (one is Digital, the other is Analog) for you to install Grove modules. Features Seeeduino/Arduino compatible Up to10m communication distance in house without...
Item #: SS-ARD105B1P -
The Danger Shield is an add-on for the Arduino & Freeduino micro controller boards. It contains a variety of fun and useful electronic circuits that you can use to do fun and useful things. It is a fully self-contained shield. You plug it into your Arduino, and you can immediately start using it. No extra things to hook up, no external components. Just a really rad board ready to rock. Note: This is a kit- Assembly & Soldering is required. Some of the features of the board are: 3...
Item #: SS-SLD01106P -
The EL Shield kit is an easy to use shield to control electroluminescent (EL) devices (such as EL wire) with either an Arduino or Seeeduino. The board has 4 outputs so you can control up to 4 devices separately! It can drive EL wires at long as 15 m (49 ft). This shield come without the headers soldered on, so you'll have to attach them before use. If you know how to control an LED, you can control EL devices. The EL Shield makes it that easy! The shield uses pulse-width modulation (PWM), so...
Item #: SS-SLD33149P -
Description The GPRS (General Packet Radio Service) Shield is a new nonvoice value added service that delivers GSM/GPRS 850/900/1800/1900MHz performance for voice, SMS, Data, and Fax in a small form factor and with low power consumption. It is controlled via AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands), and fully compatible with Seeeduino/Arduino and Mega. The GPRS Shield has 12 GPIOs 2 PWMs and 1 ADC(They are all 2V8 logic). Features Quad-Band 850/ 900/ 1800/ 1900 MHz GPRS...
Item #: SS-SLD80256P -
Quickly add motor control to your Arduino or Seeeduino with the Grove Motor Shield! You can use the shield to easily connect 2 brushed DC motors, which makes it great for controlling wheeled platforms like the Budget Bot Chassis. Use the Grove Motor Shield to control motors from 6-15 volts, with up to 2 amps per channel. Easily accessible screw terminals will let you connect your motors and external power. This shield is also great if you're using the Grove sensors, since it has 13 Grove ports...
Item #: SS-SLD12148P -
Check out the latest version of the Grove Sensor Shield! This shield sports a simplified design and additional I2C ports The Grove base shield will allow you to easily connect Grove sensor and output modules to your Arduino or Arduino compatible board. Just connect the Grove Sensor Shield to your Arduino and use a Grove Universal Cable to connect the shield to one of our many Grove Modules. The Grove systemuses 4-pin 2mm header. This allows for up to two digital or analog per cable, enabling...
Item #: SS-INT109B2P -
Every project is better with music! Build your own music player with the music shield. Or use it to give your robot a voice and/or sound effects. The Music Shield is an ipod/iphone dock compatible shield. It can work with Arduino, Seeeduino, Seeeduino Mega and Arduino Mega2560. It is based on the VS1053b and can play variety of music format stored on MicroSD card with Seeed Studio provided Arduino Library. Note: Recording is only supported by Seeeduino Mega and Arduino Mega2560. Documentation...
Item #: MG-E000008 -
If you need a lot of inputs and/or outputs, this is your solution! The Mux (Multiplexer) Shield adds the capacity for up to 48 inputs or outputs on the Arduino and Arduino Mega. Using three Texas Instruments CD74HC4067 Analog Multiplexers, the Mux Shield makes it possible to have 48 analog/digital inputs or digital outputs in many combinations. The Mux Shield comes with 5V and Ground headers so you'll have power available to each input or output and comes with stackable headers installed. The...
Item #: RG-SENSHIELDV2 -
The Arduino Platform is a great way for learning about electronics and programming, as well as creating microcontoller based projects. But even simple projects can get messy very quickly, leaving you with a pile of wires, breadboards, and components. With the RobotGeek Sensor System, you can put your project on the fast track and get it up and running in no time. The RobotGeek Sensor Shield will fit on any Standard Arduino Compatible board*, and break out the digital and analog pins into easy...
Item #: SS-WLS06201P -
Seeed's Wifi Shield utilizes a RN171 wifi module to provide your Arduino with serial ethernet function. It only takes two pins to hook your device up to 802.11 b/g wireless networks! It features an independent antenna which can cover a wider range and transmit stronger signals. The wifi shield supports common TCP, UDP and FTP communication protocols creating a perfect solution to most wireless network projects such as smart home networks, robotic control, personal weather stations,...
Item #: SS-SLD01103P -
The newest version of the Xbee Shield is a standardized and stackable shield for Arduino. You can easily stack any modules from the Bee series and build a wireless network for your project! In spite of that, it is also equipped with the function of level conversion which enables a double-way conversion between high and low IO levels. The reversed digital pins facilitate users to select TX-RX ports using jumper caps.***Seeed Studio's XBee Shield V2.0 comes unassembled and will require soldering...
Item #: SS-SLD62445P -
2.8'' TFT Touch Shield is an Arduino / Arduino Mega compatible multicolored TFT display with a 4-wire resistive touch-screen. It is available in an Arduino shield compatible pinout for attachment. The TFT driver is based on ST7781R with 8bit data and 4bit control interface. Arduino / Mega Shield compatible footprint. TFT Resolution : 240 x 320 pixels Size : 2.8" (50.0 x 69.2 x 2.5 mm) Colors : 262K Backlight : LED Driver IC: ST7781R 4-Wire Resistive Touch Screen Application Ideas As a...
Item #: SS-SLD90147P -
Are your Arduino Mega and Android device ready to tie the knot and start communicating? The Grove Mega Shield will get the two working together in beautiful harmony. The Mega Shield has 22 digital pins as well as 16 analog pins. All pins are connected via 4-pin connections (2 signal pins, VCC and GND), and 12 of the digital pins are connected to 3-pin connections (Signal, VCC and GND) suitable for servos and electronic bricks. The Grove Mega Shield is compatible with... Arduino Mega 1280/2560...
Item #: SS-ACC08101P -
Screw shield is a wing-like shield that extends both sides of your Arduino or Arduino variants into sturdy and reliable screw terminal blocks. On the digital pins side, it contains 18 terminals: 16 normal terminals and 2 extra GND. As to the Analog pins side, there are 16 terminals (12 normal terminals, 4 extra terminals for Vin, 2*GND and 5V) and 2 breakout through holes for 2 additional ADC pins. Sweetly, a special extension block for SPI interface is included in this product to...
Item #: SS-INT108B1P -
A Protoshield kit for Seeeduino/Arduino MEGA. Miles of space with a huge amount of header options. Kit also comes with 5 button switches. Excellent kit for building your own MEGA shield. Features Supports both Seeeduino MEGA and Arduino MEGA All pins are brought to the top level Supports Xbee/GPS bee Rest button brought to the top level 5 button switches Tons of male and female headers Product WIKI Page. ...
Item #: SS-POW10301P -
The Robust EL Inverter For EL Shield turns DC voltage from your Arduino or Geekduino into high frequency AC for powering electroluminescent (EL) devices. The rated input voltage is 3.3-5 V, so it should work well with most micro-controllers. It produces high frequency 110 V AC which is perfect for powering EL wire. Keep in mind that it does produce a quiet but audible high frequency noise when connected to power. In most applications it won't be noticeable. This inverter can power up to 15 m...
Item #: SS-ELB127E4P -
Electronic Brick Chassis is a modular 'plug n play' style dedicated Arduino, Seeeduino, and Freeduino interface shield. It breaks out your Duino's available I/O with convenient 3-pin ports and data buses. Plug in a variety of Phidgets & Electronic Brick Sensors, Inputs, Outputs, and Accessories! Yes! We can build electronics projects just as easy as piling bricks. The Arduino/Freeduino movement has made programming and physical computing easier than ever. The Electronic Brick...