Item #: MG-A000066 -
The Arduino Uno R3 is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Uno differs from all...
Item #: RG-GEEKDUINO -
The Geekduino is the new Arduino Compatible board from RobotGeek! This board goes into every RobotGeek Robot Kit and is the perfect microcontroller for your next robotic project! The Geekduino uses the ubiquitous Micro USB port to power and program the board. The Geekduino can also be powered via the ultra low-profile flat DC power jack. A series of switches allows you to toggle on/off the Geekduino's FTDI reset (handy for software projects) as well as change the operating voltage of the...
Item #: MG-A000065 -
The Wireless SD Shield provides a 3.3v regulated Digi Xbee slot for easy wireless connectivity, a uSD (micro Secure Digital) slot for onboard storage capabilities, and a compact prototyping board area for custom additions. Transmission LED indicator lights, a reset button, and serial select switch are also available for your convenience. Passthrough headers allow for additional Shields to be stacked on top.More information available soon!
Item #: AF-815 -
Want to make a hexapod walker? Maybe you're making a piece of art with tons of moving parts, or you need to drive a ton of LEDs with precise PWM output. Your microcontroller has a limited number of PWM outputs, and you find yourself running out! Not with the Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface. With this pwm and servo driver breakout, you can control 16 free-running PWM outputs with just two pins! Need to run more than 16 PWM outputs? No problem. Chain together up to 62...
Item #: KIT-PRO-PROG -
The Arbotix-Pro Programming Kit contains an ST-Link/V2 USB Programmer and Olimex JTAG cable adapter. This programming kit is intended for advanced users only, custom programming of the Arbotix-Pro is not covered under technical support and is at the user’s own risk. Improper usage can permanently brick or destroy your Arbotix-Pro. Please pay attention to the orientation of the programming cable as improper orientation will destroy the board. The ST-LINK/V2 is an in-circuit debugger and...
Item #: IL-ARBOTIXPRO -
The Arbotix-Pro is a robotics sub-controller based around the STM32F103 Cortex M3 ARM microprocessor. It functions as a ‘brain stem’ to a main CPU, allowing users to interface to servos, sensors, lower level communication buses such as TTL serial or I2C, and power all through one convenient USB connection and communication protocol.The Arbotix-Pro is built around using Dynamixel Robot actuators and has support for both TTL or RS-485 communication, to control AX, MX, and Dynamixel-PRO actuators...
Item #: KIT-PRO -
Get going with the ArbotiX-Pro Robocontroller Starter Kit! This kit contains an ArbotiX-Pro Robocontroller, an AX/MX Power Hub, 10 200mm Dynamixel Compatible Cables, a USB-A to Micro cable, and a 12V 10A Power Supply. The Arbotix-Pro is a robotics subcontroller based around the STM32F103 Cortex M3 ARM cpu. It has support for both TTL or RS-485 communciation, to control AX, MX, and Dynamixel-PRO actuators from ROBOTIS. Interface to the main CPU of a robot is provided via USB, Xbee, or UART, all...
Item #: ED-ARD -
This board provides your Edison with the ability to interface with Arduino Shields, or essentially any board with an Arduino footprint, giving you access to extensive shield libraries and resources. Pins are laid out in the same location arrangement as on the Arduino Uno R3 (Arduino 1.0 pinout). This breakout includes a micro USB device connector and a dedicated standard size USB 2.0 host Type-A connector selected via a mechanical microswitch, a UART2 connected micro USB device port, and a...
Item #: ED-IOTMOD -
The Intel® Edison is a incredible tiny computer - at 35.5 × 25.0 × 3.9 mm, it's about the size of an SD card! But despite its tiny stature, this little board boasts some big power. With a dual core, dual threaded Intel® Atom CPU running at 500mhz and 1GB of RAM, the Intel® Edison has no problem running Yocto Linux 1.6. This board even has an additional 32 bit Intel® Quark microcontroller running1 at 100MHz and 4GB of flash storage. And don't forget about wireless connectivity - the Intel®...
Item #: ED-BREAKOUT -
This basic breakout board is slightly larger than the Edison module, giving you easy access to a basic set of features without heavily increasing its footprint. The board has a USB OTG with USB micro type-AB connector, a USB OTG power switch, a USB to device UART bridge with micro type-B connector, a battery charger, and a power supply. It exposes the native 1.8V I/O of the Edison module, and gives you a 0.1 inch grid I/O array of through-hole solder points to work with. The Intel® Edison is a...
Item #: RG-RFIDUINO1 -
RFIDuino v2 is here This page is for the RFIDuino V1.1. Visit this guide to see the differences between the Version 1.1 and 1.2 Hardware. The RFIDuino is an Arduino RFID Shield which makes Arduino RFID projects super easy to build. Just drop the RFIDuino Shield onto your Arduino microcontroller, load our sample code, and you'll be reading tags in no time! Our getting started guide will take you through the process of working with the RFIDuino from loading basic code to more advanced projects...
Item #: RG-RFIDUINO -
This page is for the RFIDuino V1.2. Visit this guide to see the differences between the Version 1.1 and 1.2 Hardware.The RFIDuino is an Arduino RFID Shield which makes Arduino RFID projects super easy to build. Just drop the RFIDuino Shield onto your Arduino microcontroller, load our sample code, and you'll be reading tags in no time! Our getting started guide will take you through the process of working with the RFIDuino from loading basic code to more advanced projects like triggering relays...
Item #: SF-DEV12646 -
Is the Arduino Uno's hardware just not cutting it? Do you need a more powerful platform, but you're not ready to move away from the Arduino IDE? Then the Teensy is the perfect ARM based micorcontroller for your next robot project. The Teensy 3.1 is a complete USB-based microcontroller development system and is as versitile as it is powerful. A custom Teensy installer and bridge application will easily allow you to write sketches for the Teensy and load them on to the Teensy. All programming is...
Item #: MG-A000062 -
The Arduino Due represents the next generation of Arduino hardware. This board is based on the Atmel SAM3X8E ARM Cortex-M3 CPU, a 32-bit, 84 MHz microcontroller. This board will give you 96 Kbytes of SRAM, as well as 512 Kbytes of flash memory to hold store your code. The Due even has a DMA controller to help relieve the processor of memory intensive tasks. The Arduino Due has some amazing capabilities. It has 54 Digital I/O pins, 12 of which can be used for PWM. The Due can use any of these...
Item #: MG-A000057 -
The Arduino Uno is a great place to start in the Arduino World, but sometimes you need a few extra features to get your project up and running. The Arduino Leonardo , a variant of the Uno, is just the board you need! So what's so special about the Leonardo? The Leonardo can easily act as USB HID(Human Interface Device) such as a Keyboard or Mouse, opening a whole class of projects for you to explore with yout Arduino. This is accomlished by using the ATmega32u4, a microcontroller that acts...
Item #: MG-A000067 -
Overview The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter...
Item #: MG-A000063 -
Overview The Arduino ADK is a microcontroller board based on the ATmega2560 (datasheet). It has a USB host interface to connect with Android based phones, based on the MAX3421e IC. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. The ADK is based on the Mega 2560. Similar to the Mega 2560 and Uno, it features an...
Item #: SF-DEV-09219 -
It's blue! It's skinny! It's the Arduino Pro! SparkFun's minimal design approach to Arduino. This is a 5V Arduino running the 16MHz bootloader (select 'Arduino Duemilanove w/ 328' within the Arduino software). The power switch was moved to the side of the board (good idea Limor!) to allow control when a shield is attached. Please note: The right-angle power switch is fragile. We're working on making the switch stronger. For now, please be gentle. Arduino Pro does not come with connectors...
Item #: SF-DEV11113 -
It's blue! It's thin (0.8mm)! It's the Arduino Pro Mini! SparkFun's minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader (select 'Arduino Duemilanove w/ 328' within the Arduino software). Arduino Pro Mini does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We recommend first time Arduino users start with the Duemilanove. It's a great board that will get you up and running quickly. The Arduino...
Item #: SL-Netduino -
Software, meet hardware. Netduino is an open source electronics platform using the .NET Micro Framework. Featuring a 32-bit microcontroller and a rich development environment. Suitable for engineers and hobbyists alike. Code. Debug. Repeat. .NET Micro Framework combines the ease of high-level coding and the features of microcontrollers. Enjoy event-based programming, multi-threading, line-by-line debugging, breakpoints and more. Design files included. Netduino is an open source electronics...
Item #: KIT-RG-GEEKSHIELD -
Everything you need to be up and running with a Geekduino and Sensor shield I/O break out board to mount to your projects. GeekduinoSensor Shield10 Robotgeek sensor cablesDuino Mounting PlateThe Robotgeek Sensor Shield breaks out the digital and analog pins into easy to use 3-pin connectors. Each connector supplies 5 volts, ground, and a signal pin. These connectors can easily be connected to RobotGeek Sensors as well as a wide variety of sensors, actuators and output...
Item #: SS-ARD128D2P -
Seeeduino v3.0 328P is an Arduino-compatible board. Its design is based on Duemilanove scheme, 100% compatible to existing programs, shields and IDEs. On the hardware however, many changes have been made to improve the flexibility and user experience. Arduino is an open-source electronics prototyping platform based on flexible, easy-to-use hardware and software. It's intended for artists, designers, hobbyists, and anyone interested in creating interactive objects or environments. ...
Item #: SF-DEV-07914 -
Description: Riding on the waves of the very popular Arduino USB board is this small prototyping shield. Originally spawned with collaboration between the folks at SFE and ITP @ NYU, the Protoshield mates with the Arduino USB board and gives the user a small soldering area, two general LEDs, access to a BlueSMiRF socket, a general pushbutton switch, and most important of all - the Arduino reset switch is brought to the top level. This comes in kit form and must be soldered together by the end...
Item #: MG-A000072 -
The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100ethernet chip (datasheet). The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps...
Item #: MG-A000079 -
Are you ready to start controlling the universe with your Arduino? Or at least some beefier motors? Built around the L298 chip, the Arduino Motor Shield is a dual full-bridge driver. This shield is designed to drive inductive loads such as relays, solenoids, DC and stepping motors – anything your poor little Arduino would burn up on if it tried to drive them itself. You’ll be able to drive two motors via 8 pins on your Arduino. Each channel will allow you to control speed and direction, as...
Item #: SF-DEV-09815 -
This is a motor shield for Arduino that will control two DC motors. Based on the L298 H-bridge, the Ardumoto can drive up to 2 amps per channel. The board takes its power from the same Vin line as the Arduino board, includes blue and yellow LEDs to indicate active direction, and all driver lines are diode protected from back EMF. Control for motor attached to OUT1/2 is connected to digital line 12 (direction A) and digital line 10 (PWM A). Control for motor attached to OUT3/4 is...
Item #: SS-SLD63030P -
The Bluetooth Shield integrates a Serial Bluetooth module. It can be easily used with Arduino/Seeedstudio for transparent wireless serial communication. You can choose two pins from Arduino D0 to D7 as Software Serial Ports to communicate with Bluetooth Shield (D0 and D1 is Hardware Serial Port). The shield also has two Grove connectors (one is Digital, the other is Analog) for you to install Grove modules. Features Seeeduino/Arduino compatible Up to10m communication distance in house without...
Item #: SS-ARD105B1P -
The Danger Shield is an add-on for the Arduino & Freeduino micro controller boards. It contains a variety of fun and useful electronic circuits that you can use to do fun and useful things. It is a fully self-contained shield. You plug it into your Arduino, and you can immediately start using it. No extra things to hook up, no external components. Just a really rad board ready to rock. Note: This is a kit- Assembly & Soldering is required. Some of the features of the board are: 3...
Item #: SS-SLD01106P -
The EL Shield kit is an easy to use shield to control electroluminescent (EL) devices (such as EL wire) with either an Arduino or Seeeduino. The board has 4 outputs so you can control up to 4 devices separately! It can drive EL wires at long as 15 m (49 ft). This shield come without the headers soldered on, so you'll have to attach them before use. If you know how to control an LED, you can control EL devices. The EL Shield makes it that easy! The shield uses pulse-width modulation (PWM), so...
Item #: SS-SLD33149P -
Description The GPRS (General Packet Radio Service) Shield is a new nonvoice value added service that delivers GSM/GPRS 850/900/1800/1900MHz performance for voice, SMS, Data, and Fax in a small form factor and with low power consumption. It is controlled via AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands), and fully compatible with Seeeduino/Arduino and Mega. The GPRS Shield has 12 GPIOs 2 PWMs and 1 ADC(They are all 2V8 logic). Features Quad-Band 850/ 900/ 1800/ 1900 MHz GPRS...
Item #: SS-SLD80256P -
Quickly add motor control to your Arduino or Seeeduino with the Grove Motor Shield! You can use the shield to easily connect 2 brushed DC motors, which makes it great for controlling wheeled platforms like the Budget Bot Chassis. Use the Grove Motor Shield to control motors from 6-15 volts, with up to 2 amps per channel. Easily accessible screw terminals will let you connect your motors and external power. This shield is also great if you're using the Grove sensors, since it has 13 Grove ports...
Item #: SS-SLD12148P -
Check out the latest version of the Grove Sensor Shield! This shield sports a simplified design and additional I2C ports The Grove base shield will allow you to easily connect Grove sensor and output modules to your Arduino or Arduino compatible board. Just connect the Grove Sensor Shield to your Arduino and use a Grove Universal Cable to connect the shield to one of our many Grove Modules. The Grove systemuses 4-pin 2mm header. This allows for up to two digital or analog per cable, enabling...
Item #: SS-INT109B2P -
Every project is better with music! Build your own music player with the music shield. Or use it to give your robot a voice and/or sound effects. The Music Shield is an ipod/iphone dock compatible shield. It can work with Arduino, Seeeduino, Seeeduino Mega and Arduino Mega2560. It is based on the VS1053b and can play variety of music format stored on MicroSD card with Seeed Studio provided Arduino Library. Note: Recording is only supported by Seeeduino Mega and Arduino Mega2560. Documentation...
Item #: MG-E000008 -
If you need a lot of inputs and/or outputs, this is your solution! The Mux (Multiplexer) Shield adds the capacity for up to 48 inputs or outputs on the Arduino and Arduino Mega. Using three Texas Instruments CD74HC4067 Analog Multiplexers, the Mux Shield makes it possible to have 48 analog/digital inputs or digital outputs in many combinations. The Mux Shield comes with 5V and Ground headers so you'll have power available to each input or output and comes with stackable headers installed. The...
Item #: RG-SENSHIELDV2 -
The Arduino Platform is a great way for learning about electronics and programming, as well as creating microcontoller based projects. But even simple projects can get messy very quickly, leaving you with a pile of wires, breadboards, and components. With the RobotGeek Sensor System, you can put your project on the fast track and get it up and running in no time. The RobotGeek Sensor Shield will fit on any Standard Arduino Compatible board*, and break out the digital and analog pins into easy...
Item #: SS-WLS06201P -
Seeed's Wifi Shield utilizes a RN171 wifi module to provide your Arduino with serial ethernet function. It only takes two pins to hook your device up to 802.11 b/g wireless networks! It features an independent antenna which can cover a wider range and transmit stronger signals. The wifi shield supports common TCP, UDP and FTP communication protocols creating a perfect solution to most wireless network projects such as smart home networks, robotic control, personal weather stations,...
Item #: SS-SLD01103P -
The newest version of the Xbee Shield is a standardized and stackable shield for Arduino. You can easily stack any modules from the Bee series and build a wireless network for your project! In spite of that, it is also equipped with the function of level conversion which enables a double-way conversion between high and low IO levels. The reversed digital pins facilitate users to select TX-RX ports using jumper caps.***Seeed Studio's XBee Shield V2.0 comes unassembled and will require soldering...
Item #: C-100-902MSD -
Need a fast and simple solution for controlling your servos, mini linear actuators or Robowinches? The Dual Servo Driver is a great low cost solution. Just plug in power and your actuators and your done! Now you can manually control two servos with a simple device, the Dual Manual Servo Driver. You can power this unit with either a 4.8-6V battery or regulated power supply. Each knob proportionally controls the corresponding servo. The potentiometers can even be taken off and wired away from...
Item #: SF-ROB-09402 -
Description: The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse. EasyDriver requires a 7V to 30V supply to power the motor, and has an on board voltage regulator for the digital interface. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors. This is the newest version of EasyDriver V4...
Item #: PH-1066 -
The PhidgetServo 1-Motor is a USB based controller that can control a Remote Control (RC) servo motor. The motor output is powered directly from the USB port. The PhidgetServo has a step accuracy of 0.1 degrees, but the actual positional accuracy of the servo motor is dependant on the physical characteristics of the specific servo used. If you need a servo with this controller, buy the kit instead and save some money. Comes packaged with a 6-foot USB Cable, and a Getting Started Manual. For...
Item #: C-100-DC-2x5 -
Product Description Sabertooth 2X5 is the motor driver of choice for small differential-drive robots. It is ideal for smaller robots- up to 3lbs in combat or 25 lbs for general purpose use. It is also a great choice in any application where you need to control two brushed motors. Out of the box, the Sabertooth can supply two DC brushed motors with up to 5A each continuously. Peak currents of 10A are achievable for short periods. Because Sabertooth 2x5 incorporates soft current limiting and...
Item #: SS-SLD62445P -
2.8'' TFT Touch Shield is an Arduino / Arduino Mega compatible multicolored TFT display with a 4-wire resistive touch-screen. It is available in an Arduino shield compatible pinout for attachment. The TFT driver is based on ST7781R with 8bit data and 4bit control interface. Arduino / Mega Shield compatible footprint. TFT Resolution : 240 x 320 pixels Size : 2.8" (50.0 x 69.2 x 2.5 mm) Colors : 262K Backlight : LED Driver IC: ST7781R 4-Wire Resistive Touch Screen Application Ideas As a...
Item #: SS-SLD90147P -
Are your Arduino Mega and Android device ready to tie the knot and start communicating? The Grove Mega Shield will get the two working together in beautiful harmony. The Mega Shield has 22 digital pins as well as 16 analog pins. All pins are connected via 4-pin connections (2 signal pins, VCC and GND), and 12 of the digital pins are connected to 3-pin connections (Signal, VCC and GND) suitable for servos and electronic bricks. The Grove Mega Shield is compatible with... Arduino Mega 1280/2560...
Item #: PH-1061 -
The PhidgetAdvancedServo 8-Motor allows you to control the position, velocity, and acceleration of up to 8 RC servo motors. It requires a 6-15VDC external power supply; its switching power supply allows the 1061 to efficiently operate from 6 to 15 VDC and can be used with a wide range of batteries. The 1061 has a high resolution of 125 steps per degree; it measures the power consumption of each servo and its switching regulator protects the motors from overvoltage. It powers servo motors of up...
Item #: SS-ARD127D2P -
The Rainbowduino board is an Arduino compatible controller board for driving LEDs. It will drive an 8x8 RGB Led Matrix (Common Anode). Work Modes The Rainbowduino can run in different work modes depending on your needs. Standalone Mode (plug and shine) UART Mode (Send data from your computer to one Rainbowduino.) I2C Mode (Send data from your computer to multiple Rainbowduino’s.) I2C Cascading (PC or Arduino generated frames displayed on multiple Led Matrices.) Features Pairs with 8x8 RGB Led...
Item #: SS-ACC08101P -
Screw shield is a wing-like shield that extends both sides of your Arduino or Arduino variants into sturdy and reliable screw terminal blocks. On the digital pins side, it contains 18 terminals: 16 normal terminals and 2 extra GND. As to the Analog pins side, there are 16 terminals (12 normal terminals, 4 extra terminals for Vin, 2*GND and 5V) and 2 breakout through holes for 2 additional ADC pins. Sweetly, a special extension block for SPI interface is included in this product to...
Item #: SS-INT108B1P -
A Protoshield kit for Seeeduino/Arduino MEGA. Miles of space with a huge amount of header options. Kit also comes with 5 button switches. Excellent kit for building your own MEGA shield. Features Supports both Seeeduino MEGA and Arduino MEGA All pins are brought to the top level Supports Xbee/GPS bee Rest button brought to the top level 5 button switches Tons of male and female headers Product WIKI Page. ...
Item #: C-900-RM-G145 -
The RoBoard RM-G144 Magnetic Compass, ±16 3-Axis Accelerometer Board combines the HMC5843, a 3-axis magneto-resistive sensor with the ADXL345, a 3-axis accelerometer. The communication is done via I2C and the sensor connects easily to the RB-100 and RB-110 single board computers. The dimension of this sensor is only 20 x 20 mm. The I2C interface cable is included. The HMC5843 is a surface mount multi-chip module designed for low field magnetic sensing with a digital interface for applications...