Motors

Show
EMAX Mini Servo back view
SS-ROB12745M
Price: $9.90 In Stock
Item #: SS-ROB12745M -

    Bigger isn't always better - and the EMAX 9g ES08A High Sensitivity Mini Servo will prove it! The small form factor and low weight of this servo makes it perfect for a vast range of smaller scale projects. Set Contains 4 Servo Horns 3 Screws Specifications Operating voltage: 4.2-6V Operating speed: 0.10sec/60degree(4.8v) Stall torque: 1.8kg/cm Temperature range: 0°-55° Dimensions : 32x11.5x24mm Weight:9g Temperature range: 0°-55° ...

    Grove - Electromagnet
    SS-811014001
    Price: $8.90 In Stock
    Item #: SS-811014001 -

      An electromagnet is a type of magnet in which the magnetic field is produced by electric current. An electric current flowing in a wire creates a magnetic field around the wire, due to Ampere's law(see drawing below). To concentrate the magnetic field, in an electromagnet the wire is wound into a coil with many turns of wire lying side by side. The magnetic field of all the turns of wire passes through the center of the coil, creating a strong magnetic field there. Grove - Electromagnet can...

      RobotGeek Pumping Station arduino pump, arduino liquid pump, arduino water pump, arduino pump tutorial
      RG-SPUMP
      Price: $39.95 In Stock
      Item #: RG-SPUMP -

        If you are looking for an Arduino Pump solution the RobotGeek Pumping Station is a perfect all-in-one pumping kit. Inside the box is a small powerful liquid pump, RobotGeek Relay, manual run button, and power supply jack. The pump is self priming and food safe so it can be used for projects involving plant watering, suction, drainage, drink dispensing, barbots, and more. The Pumping Station makes it a breeze to build Arduino pump projects. Just plug in a sensor cable and power supply to add a...

        12v DC Motor Pump - Full View
        TI-TG-02B-DC12B
        Price: $24.95 In Stock
        Item #: TI-TG-02B-DC12B -

          If you are looking for an Arduino Pump the RobotGeek Large Liquid Pump is a great solution. This pump is self priming, quiet, food safe, and can move up to 2 liters per minute. To use this for an Arduino Pump project all you need is a RobotGeek Relay and seperate power supply. The pump will work with standard aquarium tubing. The fit is a little tight, but the tubing will go on. We recommend picking up some of our 3.5mm food safe silicone tubing which fits great and goes on easier! Recommended...

          RobotGeek 12v Mini Self-Priming Pump
          RG-SMPUMP
          Price: $17.95 In Stock
          Item #: RG-SMPUMP -

            If you are looking for an Arduino Pump the RobotGeek small liquid and air pump is a great solution. This pump is self priming and food safe so it can be used for projects involving plant watering, suction, drainage, drink dispensing, barbots, and more. To use this for an Arduino Pump project all you need is a RobotGeek Relay and seperate power supply. The pump can operate at either 6 or 12 volts and packs a punch in a small package! Recommended Arduino Pump Tutorials: Arduino ShotBot Project...

            Food Safe Clear Silicone Tubing 3.5mm (10 Meters) food safe clear silicone tubing, food tubing, food safe tubing, silicone tube, safe clear tube, clear tube, clear tubing
            RAW-TUBING
            Price: $19.95 In Stock
            Item #: RAW-TUBING -

              If you're looking for a silicone tube solution for our DC Liquid Pump or Water Valve, or a better alternative to standard US 1/8" tubing? We've got it! Our silicone tubing comes in 10 meter rolls and is food safe! We've sourced this tubing to make sure that it easily fits onto our pump and solenoid, but it still strong enough to stay on.

              Solenoid Valve arduino Solenoid valve, arduino solenoid water valve, solenoid liquid valve, arduino solenoid valve, arduino water valve, arduino liquid valve
              HW-WVALVE
              Price: $19.95 In Stock
              Item #: HW-WVALVE -

                If you are looking for an Arduino solenoid valve the RobotGeek liquid solenoid valve is a perfect solution. Compact, food safe, and with mounting holes make it a great fit for DIY projects of all kinds. The Solenoid Valve is a great companion to the Large DC Liquid Pump and the Small DC Liquid Pump. When building pumping projects sometimes it is necessary to add a valve to stop either liquid back draw or unwanted flow. When using diaphram pumps if your liquid supply is higher than your pouring...

                9g Servo Bracket
                SS-ROB71155P
                Price: $9.90 Back Order
                Item #: SS-ROB71155P -

                  Do you need some mounting hardware for your mini servo? Then 9g Servo Bracket Set is for you. This yoke and bracket kit is ideal for use with mini-servos, and works perfectly with the EMAX 9g ES08A Mini Servo NOTE: This set does NOT include any servos. Set Includes : 2 - Brackets 1 - Yoke 4 - Plastic Rivets (3x5.5) 8 - Plastic Rivets (2x5.6) 2 - Paper Washers 8 - Screws ...

                  RobotGeek 180 Degree Robot Servo robot servo, 180 degree robot servo, robotgeek servo, robotgeek robot servo, robotgeek 180 degree servo, 180 degree servo
                  ASM-RGS-13
                  Retail: $24.95
                  Price: $19.95 In Stock
                  Item #: ASM-RGS-13 -

                    Get ready to bring your robotic dreams to life with the RobotGeek 180 Degree Robot Servo! This metal-geared servo is perfect for building robotic joints and will help you create your own custom robotic arms, crawlers, and more! And because these servos use a standard PWM signal for control, they're easy to directly interface with microcontrollers like the Arduino! Idler Horn The difference between a regular servo and robot servo is the Idle Horn. This horn will spin freely and is at the...

                    RobotGeek Continuous Rotation Servo robotgeek 360 degree robot servo, robotgeek continuous servo, robotgeek robot servo, robot servo, robotgeek servo, continuous robot servo, continuous servo,Continuous Rotation
                    ASM-RGS-4C
                    Retail: $24.95
                    Price: $19.95 In Stock
                    Item #: ASM-RGS-4C -

                      Get ready to bring your robotic dreams to life with the RobotGeek Continuous Rotation Servo! This metal-geared servo is perfect for building robotic rovers, spinners and more! And because these servos use a standard PWM signal for control, they're easy to directly interface with microcontrollers like the Arduino! Idler Horn The difference between a regular servo and robot servo is the Idle Horn. This horn will spin freely and is at the opposite position of the main drive horn. The idler horn...

                      Sabertooth dual 5A motor driver
                      C-100-DC-2x5
                      Price: $59.99 Back Order
                      Item #: C-100-DC-2x5 -

                        Product Description Sabertooth 2X5 is the motor driver of choice for small differential-drive robots. It is ideal for smaller robots- up to 3lbs in combat or 25 lbs for general purpose use. It is also a great choice in any application where you need to control two brushed motors. Out of the box, the Sabertooth can supply two DC brushed motors with up to 5A each continuously. Peak currents of 10A are achievable for short periods. Because Sabertooth 2x5 incorporates soft current limiting and...

                        Grove - L298 Dual H-Bridge I2C Motor Driver Grove Motor driver, Arduino motor driver, arduino h-bridge, L298 Dual H-Bridge I2C Motor Driver, L298 motor driver, Grove L298 motor
                        SS-ROB72212P
                        Price: $23.50 In Stock
                        Item #: SS-ROB72212P -

                          Description The Grove I2C motor driver is a new addition to the Grove series with the same easy-to-use interface. Its heart is a dual channel H-bridge driver chip that can handle current up to 2A per channel, controlled by an Atmel ATmega8L which handles the I2C communication with for example an Arduino. Both motors can be driven simultaneously while set to a different speed and direction. It can power two brushed DC motors or one 4-wire two-phase stepper motor. It requires a 6V to 15V power...

                          Sabertooth dual 25A motor driver
                          C-100-DC-2x25
                          Price: $124.99 Back Order
                          Item #: C-100-DC-2x25 -

                            The Sabertooth 2X25 is one of the most versatile, efficient and easy to use dual motor drivers on the market. It is suitable for high powered robots - up to 100lbs in combat or 300lbs for general purpose robotics.  Out of the box, the Sabertooth can supply two DC brushed motors with up to 25A each. Peak currents of 50A per channel are achievable for a few seconds.  Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental...

                            Sabertooth dual 5A motor driver for R/C
                            C-100-DC-2x5RC
                            Price: $59.99 In Stock
                            Item #: C-100-DC-2x5RC -

                              Product Description Sabertooth 2X5 R/C is a dual motor driver specifically optimized for use in radio controlled vehicles. It is suitable for small robots, cars and boats, and especially well suited for the Antweight and Beetleweight classes of fighting robots. Out of the box, it can supply two DC brushed motors with up to 5A each. Peak currents of 10A are achievable for a few seconds. Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental...

                              SyRen 10A regenerative motor driver
                              C-100-DC-SYREN10
                              Price: $49.99 In Stock
                              Item #: C-100-DC-SYREN10 -

                                Product Description The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. It is suitable for medium powered robots - up to 30lbs in combat or 100lbs for general purpose robotics. Out of the box, the SyRen 10 can supply a single DC brushed motor with up to 10A continuously. Peak currents of 15A are achievable for a few seconds. Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental stalls...

                                RG90 Gear Motor RG90 Gear Motor, MOT-VIB08, Gear Motor, gearmotor, 6v gearmotor, 90rpm, 1:120, Arduino Motor, Robot Motor
                                MOT-VIBO8
                                Price: $5.95 In Stock
                                Item #: MOT-VIBO8 -

                                  Weighing in at just 35 grams, this RG90 Gear Motor can put put an impressive 1.2 kg/cm of torque! That makes it great for small, wheeled robots! The double-flat output shaft is 7mm in diameter and is perfect for attaching to our Gear Motor Wheel. Our gear motors come with two- 300mm wires pre-soldered onto the motor. Each wire is terminated with a 2.54mm female connector. This makes them ideal for attaching to any 2.54mm pin connector. RG90 Gear Motor Operating Voltage 6V No Load Speed 90 RPM...

                                  Sabertooth Dual 60A Motor Driver Sabertooth Dual 60A Motor Driver
                                  DE-Sabertooth2X60
                                  Price: $189.99 Back Order
                                  Item #: DE-Sabertooth2X60 -

                                    The Sabertooth 2X60 is one of the most versatile, efficient and easy to use dual motor drivers on the market. It is suitable for high powered robots - up to 120lbs in combat or up to 1000lbs for general purpose robotics.  Out of the box, the Sabertooth can supply two DC brushed motors with up to 60A each. Peak currents of 120A per channel are achievable for a few seconds.  Overcurrent and thermal protection means you'll never have to worry about killing the driver with...

                                    Sabertooth dual 12A motor driver
                                    C-100-DC-2x12
                                    Price: $79.99 In Stock
                                    Item #: C-100-DC-2x12 -

                                      Product Description The Sabertooth 2X12 is one of the most versatile, efficient and easy to use dual motor drivers on the market. It is suitable for medium powered robots - up to 30lbs in combat or 100lbs for general purpose robotics.  Out of the box, the Sabertooth can supply two DC brushed motors with up to 12A each. Peak currents of 25A are achievable for a few seconds.  Overcurrent and thermal protection means you'll never have to worry about killing the driver with...

                                      Sabertooth dual 12A motor driver for R/C
                                      C-100-DC-2x12RC
                                      Price: $64.99 In Stock
                                      Item #: C-100-DC-2x12RC -

                                        Sabertooth 2X12 R/C is a dual motor driver specifically optimized for use in radio controlled vehicles. It is suitable for medium powered robots, cars and boats. The Sabertooth 2x12 R/C replaces our 2x10 RC controller. Out of the box, it can supply two DC brushed motors with up to 12A each. Peak currents of 25A are achievable for a few seconds. Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental stalls or by hooking up too big a motor....

                                        Bipolar Stepper Motor
                                        SF-ROB-09238
                                        Price: $14.95 In Stock
                                        Item #: SF-ROB-09238 -

                                          Description: This is a simple, but very powerful stepper motor with a 4-wire cable attached. Features: Step Angle (degrees) :1.8 2 Phase Rated Voltage : 15.4V Rated Current : 0.28A Holding Torque : 2.4kg*cm Detent Torque : 120g*cm Documents: Datasheet ...

                                          Dual VNH3SP30 Motor Driver Carrier MD03A Dual, VNH3SP30, Motor, Driver, Carrier, MD03A, DC, Controller
                                          PO-707
                                          Price: $49.99 Back Order
                                          Item #: PO-707 -

                                            If you are looking to drive two high-power motors through one compact unit, these dual VNH3SP30 motor driver carriers are perfect for you. With these boards, it's easy to get a medium-sized, differential drive robot running in no time. The Pololu dual high-power motor drivers are compact carriers for the VNH3SP30 and VNH2SP30 motor driver integrated circuits from ST. The board incorporates most of the components of the typical application diagram on page 8 of the VNH2SP30 datasheet, including...

                                            HB-25 Motor Controller
                                            PX-29144
                                            Price: $49.99 In Stock
                                            Item #: PX-29144 -

                                              The Parallax HB-25 Motor Controller is one of our best solutions for DC motor control. This module is dependable and highly-compatible with any microcontroller that can generate a servo compatible pulse. In the simplest sense the HB-25 allows a DC Motor to be controlled much like a Continuous Rotation Servo. While the signals are compatible, the HB-25 does not require refreshing as a servo does. A single pulse can maintain the output.   The HB-25 Motor Controller has the...

                                              L12 100mm 100:1 Linear Actuator Firgelli Linear Actuator, mini linear actuator, small linear actuator, small arduino linear actuator
                                              FR-L12-100-100-6-I
                                              Price: $90.00 In Stock
                                              Item #: FR-L12-100-100-6-I -

                                                Firgelli mini linear actuators are excellent for DIY and Arduino mini linear actuator projects. The L12-I series can be controlled from a regular servo PWM signal as well as voltage and current signaling. The PWM control is perfect for Arduino linear actuator projects because the actuator can be controlled just like a servo using the servo library. We recommend checking out our Arduino Linear Actuator Tutorials listed below. Each linear actuator also comes with mounting hardware and end...

                                                L12 100mm 210:1 Linear Actuator small linear actuator, mini arduino linear actuator, Firgelli Linear Actuator, micro linear actuator
                                                FR-L12-100-210-6-I
                                                Price: $90.00 In Stock
                                                Item #: FR-L12-100-210-6-I -

                                                  Firgelli mini linear actuators are excellent for DIY and Arduino mini linear actuator projects. The L12-I series can be controlled from a regular servo PWM signal as well as voltage and current signaling. The PWM control is perfect for Arduino linear actuator projects because the actuator can be controlled just like a servo using the servo library. We recommend checking out our Arduino Linear Actuator Tutorials listed below. Each linear actuator also comes with mounting hardware and end...

                                                  L12 50mm 100:1 Linear Actuator Firgelli Linear Actuator, mini linear actuator, small linear actuator, small arduino linear actuator
                                                  FR-L12-50-100-6-I
                                                  Price: $90.00 In Stock
                                                  Item #: FR-L12-50-100-6-I -

                                                    Firgelli mini linear actuators are excellent for DIY and Arduino mini linear actuator projects. The L12-I series can be controlled from a regular servo PWM signal as well as voltage and current signaling. The PWM control is perfect for Arduino linear actuator projects because the actuator can be controlled just like a servo using the servo library. We recommend checking out our Arduino Linear Actuator Tutorials listed below. Each linear actuator also comes with mounting hardware and end...

                                                    L12 50mm 210:1 Linear Actuator small linear actuator, small arduino linear actuator, Firgelli Linear Actuator, mini linear actuator
                                                    FR-L12-50-210-6-I
                                                    Price: $90.00 In Stock
                                                    Item #: FR-L12-50-210-6-I -

                                                      Firgelli mini linear actuators are excellent for DIY and Arduino mini linear actuator projects. The L12-I series can be controlled from a regular servo PWM signal as well as voltage and current signaling. The PWM control is perfect for Arduino linear actuator projects because the actuator can be controlled just like a servo using the servo library. We recommend checking out our Arduino Linear Actuator Tutorials listed below. Each linear actuator also comes with mounting hardware and end...

                                                      L298 Dual H-Bridge Motor Driver L298 Dual H-Bridge Motor Driver
                                                      SS-MOT103B1M
                                                      Price: $23.50 In Stock
                                                      Item #: SS-MOT103B1M -

                                                        Double H driver module uses ST L298N dual full-bridge driver, an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the input signals. The emitters of the lower transistors of each bridge are connected together...

                                                        Motor Driver 1A Dual TB6612FNG
                                                        SF-ROB-09457
                                                        Price: $8.95 Back Order
                                                        Item #: SF-ROB-09457 -

                                                          The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - CW, CCW, short-brake, and stop. The two motor outputs (A and B) can be separately controlled, the speed of each motor is controlled via a PWM input signal with a frequency up to 100kHz. The STBY pin should be pulled high to take the motor out of standby mode. Logic supply voltage (VCC) can be in...

                                                          Unipolar Stepper Motor 12VDC
                                                          M-200-403-1010ND
                                                          Price: $27.50 In Stock
                                                          Item #: M-200-403-1010ND -

                                                            Voltage - Rated 12VDC Size - 42mm x 49.5mm x 3mm Type - Unipolar Holding Torque - 73.4/10.4 Step Angle - 7.5° Steps per Revolution - 48

                                                            Unipolar Stepper Motor 5VDC 7.5DEG
                                                            M-200-403-1019ND
                                                            Price: $20.00 In Stock
                                                            Item #: M-200-403-1019ND -

                                                              Voltage - Rated 5VDC Size - 26mm x 34.9mm x 2mm Type - Unipolar Holding Torque - 19.2/1.3 Step Angle - 7.5° Steps per Revolution - 48

                                                              2 Inch Stroke 110 LB Linear Actuator with Feedback Linear Actuator, push actuator, SPAL
                                                              M-200-50-5-1577-2
                                                              Price: $107.95 In Stock
                                                              Item #: M-200-50-5-1577-2 -

                                                                This is a 12V DC 110lb Linear Actuator from Creative Werks. (part number LACT2P) These are reliable, well built tough linear actuators. The sturdy mounting brackets make them easy to mount and won't break. If you are looking for a basic manual controller we recommend the Linear Actuator Controller kit. If you are looking to control these from an Arduino we recommend checking out the Arduino Linear Actuator tutorials below! Arduino Linear Actuator Tutorials: Preset Position Button Control of a...

                                                                4 Inch Stroke 110 LB Linear Actuator with Feedback large Linear Actuator, large arduino linear actuator, linear actuator for arduino
                                                                M-200-50-5-1577-4
                                                                Price: $109.95 In Stock
                                                                Item #: M-200-50-5-1577-4 -

                                                                  This is a 12V DC 110lb Linear Actuator from Creative Werks. (part number LACT2P) These are reliable, well built tough linear actuators. The sturdy mounting brackets make them easy to mount and won't break. If you are looking for a basic manual controller we recommend the Linear Actuator Controller kit. If you are looking to control these from an Arduino we recommend checking out the Arduino Linear Actuator tutorials below! Arduino Linear Actuator Tutorials: Preset Position Button Control of a...

                                                                  6 Inch Stroke 110 LB Linear Actuator with Feedback large Linear Actuator, large arduino linear actuator, linear actuator for arduino
                                                                  M-200-50-5-1577-6
                                                                  Price: $109.95 In Stock
                                                                  Item #: M-200-50-5-1577-6 -

                                                                    This is a 12V DC 110lb Linear Actuator from Creative Werks. (part number LACT2P) These are reliable, well built tough linear actuators. The sturdy mounting brackets make them easy to mount and won't break. If you are looking for a basic manual controller we recommend the Linear Actuator Controller kit. If you are looking to control these from an Arduino we recommend checking out the Arduino Linear Actuator tutorials below! Arduino Linear Actuator Tutorials: Preset Position Button Control of a...

                                                                    8 Inch Stroke 110 LB Linear Actuator with Feedback large Linear Actuator, large arduino linear actuator, linear actuator for arduino
                                                                    M-200-50-5-1577-8
                                                                    Price: $109.95 In Stock
                                                                    Item #: M-200-50-5-1577-8 -

                                                                      This is a 12V DC 110lb Linear Actuator from Creative Werks. (part number LACT2P) These are reliable, well built tough linear actuators. The sturdy mounting brackets make them easy to mount and won't break. If you are looking for a basic manual controller we recommend the Linear Actuator Controller kit. If you are looking to control these from an Arduino we recommend checking out the Arduino Linear Actuator tutorials below! Arduino Linear Actuator Tutorials: Preset Position Button Control of a...

                                                                      10 Inch Stroke 110 LB Linear Actuator with Feedback large Linear Actuator, large arduino linear actuator, linear actuator for arduino
                                                                      M-200-50-5-1577-10
                                                                      Price: $113.95 In Stock
                                                                      Item #: M-200-50-5-1577-10 -

                                                                        This is a 12V DC 110lb Linear Actuator from Creative Werks. (part number LACT2P) These are reliable, well built tough linear actuators. The sturdy mounting brackets make them easy to mount and won't break. If you are looking for a basic manual controller we recommend the Linear Actuator Controller kit. If you are looking to control these from an Arduino we recommend checking out the Arduino Linear Actuator tutorials below! Arduino Linear Actuator Tutorials: Preset Position Button Control of a...

                                                                        Phidgets MotorControl 1-Motor PhidgetMotorControl, PhidgetMotorControl 1-Motor, 1-Motor, Phidget Motor Control 1-Motor, Phidget Motor Control, USB Motor controller, 1065, P1065
                                                                        PH-1065
                                                                        Price: $80.00 In Stock
                                                                        Item #: PH-1065 -

                                                                          Product Features Controls direction, velocity and acceleration of one DC Motor Requires external Power Supply (9 to 28VDC) Built-in 2 digital inputs, 2 analog inputs, 1 encoder input Protected against over-current, over-voltage, and over-temperature Connects directly to a computer's USB Port Product Description The 1065 lets you control the direction, velocity and acceleration of one DC Motor. The motor is powered by an external power supply (9 to 28VDC). Brushed DC Motors are very simple to...

                                                                          Phidgets MotorControl HC PhidgetMotorControl HC, Phidget MotorControl HC, Phidget Motor Control HC, Phidgets MotorControl HC, Phidgets Motor Control HC, USB motor Controller
                                                                          PH-1064
                                                                          Price: $120.00 In Stock
                                                                          Item #: PH-1064 -

                                                                            The PhidgetMotorControl HC allows you to control the velocity and acceleration of up to two high-current DC motors. Many variations of brushed DC motors exist: permanent magnet motors, electromagnet motors, coreless motors, linear motors... the PhidgetMotorController can be used with any of these, as well as other devices like small solenoids, incandescent light bulbs, and hydraulic or pneumatic devices like small pumps and valves. Provides bi-directional control to 2 DC motors Requires...

                                                                            12 Inch Stroke 110 LB Linear Actuator with Feedback Linear Actuator, push actuator, SPAL
                                                                            M-200-50-5-1577-12
                                                                            Price: $113.95 In Stock
                                                                            Item #: M-200-50-5-1577-12 -

                                                                              This is a 12V DC 110lb Linear Actuator from Creative Werks. (part number LACT2P) These are reliable, well built tough linear actuators. The sturdy mounting brackets make them easy to mount and won't break. If you are looking for a basic manual controller we recommend the Linear Actuator Controller kit. If you are looking to control these from an Arduino we recommend checking out the Arduino Linear Actuator tutorials below! Arduino Linear Actuator Tutorials: Preset Position Button Control of a...

                                                                              Linear Actuator Mounting Bracket spal, linear actuator, mounting bracket
                                                                              M-200-50-5-1577-B
                                                                              Price: $14.25 In Stock
                                                                              Item #: M-200-50-5-1577-B -

                                                                                LINEAR ACTUATOR MOUNTING BRACKET SPAL part number LA-BRACKET-110A mounting bracket kit for use with SPAL/Creative Werks LACTP series linear actuators. Bracket and mounting pad are made from billet aluminum. Includes hardware. NOTE: This is a single bracket. If you need to mount both ends of your linear actuator you will need two brackets. SPECIFICATIONS CLEVIS Inside width 13/16" Outside width 1-1/2" Throat depth 9/16" Bracket size 1-5/16" x 1-1/2" x 1-13/32" Pad...

                                                                                Dual Linear Actuator Controller spal, linear actuator, actuator controller, wiring harness
                                                                                M-200-50-5-1577-C
                                                                                Price: $119.95 In Stock
                                                                                Item #: M-200-50-5-1577-C -

                                                                                  LINEAR ACTUATOR CONTROLLER KIT Creative Werks linear actuator controller kit for use with Creative Werks LACTP series linear actuators. Pushbuttons give manual control of travel and can also be programmed to move actuator to any of three determined preset positions. Indicator light shows at which of these custom presets unit is currently positioned. Once programmed the display unit can be removed and three SPST momentary switches (not included) added to make actuator move to preset positions...

                                                                                  10 Foot Extension Wire spal, linear actuator, actuator controller, wiring harness
                                                                                  M-200-50-5-1577-H
                                                                                  Price: $14.95 In Stock
                                                                                  Item #: M-200-50-5-1577-H -

                                                                                    10 FOOT EXTENSION HARNESS Creative Werks part number LA-EXTHARN. Ten foot wiring harness allows a Creative Werks 12 VDC 110 lb. linear actuator to be mounted up to ten feet away from the actuator controller. SPECIFICATIONS 10 feet long Shpg. 1/4 lb.

                                                                                    Little Grip Attachment Kit
                                                                                    LM-LGA-KT
                                                                                    Price: $3.00 Back Order
                                                                                    Item #: LM-LGA-KT -

                                                                                      Lexan mounting plate and hardware. Mounts a Little Grip kit to an aluminum servo "C" bracket.

                                                                                      FS90 Analog Micro Plastic Gear Servo FS90 Analog Micro Plastic Gear Servo, analog micro servo, plastic gear servo, 9g plastic servo, 9g servo, micro servo, analog servo, 9g micro servo
                                                                                      FT-FS90
                                                                                      Price: $6.95 In Stock
                                                                                      Item #: FT-FS90 -

                                                                                        Need a tiny servo for a tiny task? Try the FS90 Micro Plastic Gear Servo! This servo is great for scanning type sensors, tiny robots, and more! Each servo comes with a variety of horns. These servos use a standard PWM signal to control them. The Arduino does a great job of controlling PWM Servos, making it ideal for a variety of robotic projects. But sometimes powering these servos can be problematic. Powering servos from the Arduino's 5v regulator leads to underpowered servos, limited by both...

                                                                                        FS90MG Micro Metal Gear Servo Fitec FS90MG Micro Metal Gear Servo, metal gear servo, 9g servo, 9g metal gear servo, 9g micro metal gear servo, 9g metal servo, metal gear servo, micro servo
                                                                                        FT-FS90MG
                                                                                        Price: $9.95 In Stock
                                                                                        Item #: FT-FS90MG -

                                                                                          Need a tiny servo for a tiny task? Try the FS90 Micro Plastic Gear Servo! This servo is great for scanning type sensors, tiny robots, and more! Each servo comes with a variety of horns. The metal gears give this servo even more power and durability! These servos use a standard PWM signal to control them. The Arduino does a great job of controlling PWM Servos, making it ideal for a variety of robotic projects. But sometimes powering these servos can be problematic. Powering servos from the...

                                                                                          Parallax (Futaba) Continuous Rotation Servo servo, servos, continuous rotation servo, continuous servo
                                                                                          PX-900-00008
                                                                                          Price: $10.00 In Stock
                                                                                          Item #: PX-900-00008 -

                                                                                            The Parallax Continuous Rotation Servo is a Futaba S148 servo. It's recommended for robotics projects and includes an adjustable potentiometer to center the servo. Servos may be controlled directly from a BASIC Stamp I/O pin by using the PULSOUT command. Servo has been modified for continuous rotation. NOTES:This continuous rotation servo only work with the following brackets: E-Z Aluminum Servo Bracket , Multi-Purpose Servo Bracket, & Aluminum Servo Bracket (may need some custom...

                                                                                            RobotGeek Servo C Bracket robotgeek servo c bracket, c bracket, robotgeek bracket, robotgeek servo bracket, servo bracket, servo c bracket
                                                                                            RG-CBRACKET
                                                                                            Price: $4.95 In Stock
                                                                                            Item #: RG-CBRACKET -

                                                                                              The RobotGeek Servo C Bracket is a great tool for creating joints with your RobotGeek Servo. This bracket easily attaches to the servo's horns with just a few bolts. A variety of mounting holes on the bracket make it easy to mount the bracket to your robot or sensors in a variety of ways. The circular hole pattern on the bottom of the bracket will also attach directly to a RobotGeek Servo Horn or other brackets, allowing you to easily build up complex servo systems. Do you need hardware?...

                                                                                              RobotGeek Servo Side Bracket robotgeek servo side bracket, servo side bracket, side bracket, rg side bracket, side bracket
                                                                                              HW-SBRACKET
                                                                                              Price: $4.95 In Stock
                                                                                              Item #: HW-SBRACKET -

                                                                                                The RobotGeek Servo Side Bracket is the perfect way to mount your RobotGeek Servo to other servos and your Robot. The side bracket can attach to 5 different positions on the servo rail to make it easy to configure your robot the way you want it. The circular hole pattern on the bottom of the bracket will also attach directly to a RobotGeek Servo Horn or other brackets, allowing you to easily build up complex servo systems. Do you need hardware? RobotGeek Servos come with metric nuts and bolts,...

                                                                                                37D mm Metal Gearmotor Bracket Pair 37D mm Metal Gearmotor Bracket Pair, Gearmotor Bracket, Pololu, 37D mm Metal Gearmotor, Robot Bracket, Robot Motor Bracket
                                                                                                PO-1084
                                                                                                Price: $7.95 In Stock
                                                                                                Item #: PO-1084 -

                                                                                                  These light-weight brackets (under 15 g each) are specifically designed for the Pololu 37D mm metal gearmotors, such as the 19:1 metal gearmotor 37Dx52L mm and the 19:1 metal gearmotor 37Dx52L mm with 64 CPR encoder. Each bracket features seven mounting holes for M3 or #4-size screws along each edge, giving you a variety of mounting options. A total of twelve M3 screws (six for each bracket) are included for securing the motor to the bracket. NOTE: This set contains 2 brackets and DOES NOT...