Item #: PH-1073 -
The PhidgetSBC3 is a Single Board Computer with an integrated PhidgetInterfaceKit 8/8/8. At its most basic, it can be thought of as a Phidget that you connect using a network cable instead of USB. The PhidgetSBC3 also provides six high-speed ports that allow you to use normal USB Phidgets over its network connection. This can extend the effective range of a Phidget from USB’s maximum of 15 feet, to anywhere that your network reaches.The PhidgetSBC3 exposes an easy to use interface for setting...
Item #: PH-3852 -
The 3852 Enclosure is designed to protect the 1018 - PhidgetInterfaceKit 8/8/8 while still giving you access to the ports and terminal blocks through openings in the enclosure.There are mounting holes that go through the bottom of the enclosure, so the board can be mounted to a flat surface and the cover can snap on top.Note: Phidget Interface Kit and mounting screws not included. ...
Item #: PH-1012 -
The PhidgetInterfaceKit 0/16/16 provides: 16 Digital Inputs sensing up to 30VDC 16 Digital Outputs controlling up to 30VDC LED indicators on all I/O channels The Digital Outputs can be used to directly control substantial devices, switching up to 30VDC at up to 2 Amps. The Output acts as a switch to ground, and is protected from transient voltages typical when switching inductive devices - relays, solenoids, motors. The Outputs can be used to directly control devices requiring substantial...
Item #: PH-1017 -
Control 8 DPDT mechanical relays, switching up to 250VAC/2A or 120VDC/2A.The PhidgetInterfaceKit 0/0/8 provides Small Signal Relays with 8 Relay Outputs, rated at 250VAC, or 2 Amps, for a maximum of 60 Watts. While typical mechanical relay boards are unable to switch signals due to an oxide buildup on the contacts, the 1017 excels at switching both signals and low-power applications.
Item #: SS-COM22639P -
Description The Relay Grove is a digital normally open switch that controls a relay capable of switching much higher voltages and currents than your normal Arduino boards. When set to HIGH, the LED will light up and the relay will close allowing current to flow. The peak voltage capability is 250V at 10 amps. Please exercise great care when working with mains voltages— if in doubt contact a professional such as a licensed electrician for help. Document How to use ...
Item #: PH-1014 -
The PhidgetInterfaceKit 0/0/4 Provides a convenient way to interface your PC with various higher-voltage devices such as incandescent bulbs, high-power relays, and motors. The 0/0/4 contains 4 Relay Outputs for switching AC or DC power; the relays are Single Pole Double Throw (SPDT). Maximum DC Switching Voltage: 100VDC Maximum DC Switching Current: 5A Maximum AC Switching Voltage: 250VAC Maximum AC Switching Current: 10A Note: When a relay is in one switch position for a period of time,...
Item #: PH-1002 -
Product Features Produces a set voltage from -10V to +10V Current up to ±20mA per channel You can connect up to 4 devices Can be used to control LED and Fluorescent Dimmers, Valve Actuators, Motor Controls. Connects directly to a computer's USB Port Product Description The PhidgetAnalog 4-Output Produces a voltage over -10V to +10V. This voltage will be asserted up to +-20mA. An error will be reported when this current is exceeded, and the voltage the customer is getting is no longer accurate....
Item #: PH-1011 -
Product Features Dongle Size 2 Analog Inputs with configurable data acquisition rates 2 Digital Inputs with hardware noise filtering 2 Digital Outputs Plugs directly into a computer's USB Port Product Description Designed for customers who only need a couple of Analog Inputs, Digital Inputs or Digital Outputs, the dongle size PhidgetInterfaceKit 2/2/2 is ideal for projects where space is critical. To keep the board small, we have removed the connectors from the board and brought them out...
Item #: PH-1018 -
The PhidgetInterfaceKit 8/8/8 provides: 8 Analog Inputs 8 Digital Inputs 8 Digital Outputs The Analog Inputs are used to measure continuous quantities, such as temperature, humidity, position, pressure, etc. Phidgets offers a wide variety of sensors that can be plugged directly into the board using the cable included with the sensor. The Analog Input can measure a voltage between 0V and 5V. The analog measurement is represented in the software as a value between 0 and 1000, so a sensor...
Item #: PH-1010 -
Product Description Provides the full functionality of the 8/8/8 I/O board in a small DIP-36 package that is plugged in your own board. If you want the 8/8/8 functionality but space is an issue, or you are building a number of units and want to eliminate wiring between boards, this is the way to go. You can create a smaller system by integrating custom electronics into your PCB, and by only using connectors for the wiring required in your system. Eliminating or reducing wiring also helps...
Item #: PH-1019 -
The PhidgetInterfaceKit 8/8/8 with 6 Port USB Hub provides: * 8 Analog Inputs * 8 Digital Inputs with hardware noise filtering * 8 Digital Outputs * On-board powered 6-port full-speed (12Mbit/s) USB hub The Analog Inputs are used to measure continuous quantities, such as temperature, humidity, position, pressure, etc. Phidgets offers a wide variety of sensors that can be plugged directly into the board using the cable included with the sensor. The Digital Inputs have a Digital Input Hardware...
Item #: PH-1072 -
The PhidgetSBC is a fully functional Single Board Computer with an integrated PhidgetInterfaceKit 8/8/8. At its most basic, it can be thought of as a Phidget that you connect using a network cable instead of directly to the USB. The PhidgetSBC also provides four USB full-speed ports that allow you to use normal USB Phidgets over its network connection. This can extend the effective range of a Phidget from USB’s maximum of 15 feet, to anywhere that your network reaches. The PhidgetSBC exposes...
Item #: ASM-RG-RELAY -
Time to step up the voltage with this Arduino Relay Board. The Arduino platform is a great way to control lights, buzzers, displays and more - but what if you have a device that doesn't run on the Arduino's native 5 volts? One simple way to do it is to use the RobotGeek Relay. This little relay board will use a signal from a 5v microcontroller to make a mechanical connection. This connection is physically seprated from the arduino, meaning you can connect devices that have different voltages...
Item #: C-200-BattleSwitch -
BattleSwitch is the larger, 10A version of the popular PicoSwitch. BattleSwitch is a relay switch that you toggle via hobby radio control gear. You can use BattleSwitch to quickly and easily control glow plugs, BattleBot weaponry and more. You can activate applications with voltage levels as high as 240VAC without having to know anything about microcontroller logic levels or transistors because the relay offers full electrical isolation from your receiver electronics. BattleSwitch plugs into a...
Item #: PH-3051 -
The Dual Relay Board is an accessory to the PhidgetInterfaceKit 8/8/8. Each relay can be controlled by a separate Digital Output and can control open or close a circuit up to 240VAC at 5Amps. The relay board uses 1 analog input jack for it's power connection. Board Dimensions: 5.3 x 4.5 cm Mounting Holes: 4.6 x 3.8 cm This product is part of the Phidgets family! Phidgets are an easy to use set of USB-based building blocks for low cost sensing and control from your PC. A wide array of sensors,...
Item #: PH-3052 -
The Solid State Relay is used to switch up to 2.5 Amps at up to 40 Volts DC, or 28 Volts AC. The relay board is controlled by a digital output on the PhidgetInterfaceKit 8/8/8, the PhidgetTextLCD 8/8/8, or the PhidgetRFID v2.0 and greater. Product Manual This product is part of the Phidgets family! Phidgets are an easy to use set of USB-based building blocks for low cost sensing and control from your PC. A wide array of sensors, I/O devices, and controllers are available. To view the entire...
Item #: C-200-PICO -
Product Description PicoSwitch is a relay switch that you toggle via hobby radio control gear. You can use PicoSwitch to quickly and easily control anything from a digital camera shutter to an electric squirt gun to home lighting and more. You can activate applications with voltage levels as high as 125VAC without having to know anything about microcontroller logic levels or transistors because the relay offers full electrical isolation from your receiver electronics. PicoSwitch plugs into a...
Item #: SF-COM-10747 -
Want to control a standard wall outlet device with your micro controller, but don't want to mess with the high voltage wiring? This might just be the right device for you! The PowerSwitch Tail is designed to allow you to safely control an outlet device without exposing any 120VAC voltages. You can plug in any standard 120VAC 3-prong outlet to be controlled by most any microcontroller. This will work great with Arduino! The PowerSwitch Tail II improves on the original PowerSwitch Tail by...