Robot Cables & Wiring
Robot Cables & Wiring

Show
USB A Male to B Male - 6ft Cable USB A to B 6ft
CBL-USBA2B
Price: $4.95 In Stock
Item #: CBL-USBA2B -

    It is a standard USB A to B cable. It is 6 feet long. It has gold plated connectors. Not much else to say. Buy one if you need it. Or don't. It won't hurt our feelings honestly.

    2.1mm DC Barrel Jack to Alligator Clips 2.1mm, dc, jack, barrel, plug, alligator, clips, power, cord, testing
    AF-1328
    Price: $1.95 In Stock
    Item #: AF-1328 -

      With this 2.1mm DC Barrel Jack to Alligator Clips cable you can easily turn a wall adapter into a power supply! A high quality molded 2.1mm DC barrel jack is brought out to red (center positive) & black (ring negative) alligator clips. Works with most wall adapters. Good for 2-3 Amps and up to 24VDC.

      2.1mm DC Barrel Plug to Alligator Clips 2.1mm, dc, jack, barrel, plug, alligator, clips, power, cord, testing
      AF-1329
      Price: $1.95 In Stock
      Item #: AF-1329 -

        This 2.1mm DC Barrel Plug to Alligator Clips cable can turn any battery pack into a power supply in a snap! A high quality molded 2.1mm DC barrel plug is brought out to red (center positive) & black (ring negative) alligator clips. Good for 2-3 Amps of current, up to 24VDC. 2.1mm is near standard for electronics, and fits the Geekduino splendidly.

        6 USB Cable Extension 6, ft, foot, feet, USB, Cable, Extension, white, gold
        CBL-USBMTF-WHT
        Price: $4.95 In Stock
        Item #: CBL-USBMTF-WHT -

          Need to plug in a USB device, but it's just out of reach? Have a short USB cable with a proprietary connector? The 6' USB Extension cable is what you need! This cable has a standard USB A male connector on one end, and a standard USB A female connector on the other, allowing you to extend the reach of virtually any USB cable in your arsenal.

          Alligator Clip with Pigtail (4 Pack) Alligator Clip with Pigtail, pin header, breadboard, prototyping
          SF-CAB-13191
          Price: $2.95 Back Order
          Item #: SF-CAB-13191 -

            This is a 4 pack of wires that are pre-terminated with an alligator clip on one end and a hookup pigtail on the other. Alligator clips are a staple part for any workbench and with these cables you will be able to easily incorporate those clips into a breadboard, development platform, or anything else that you would normally be able to attach a hookup wire to. Each Alligator Clip with Pigtail cable has a wire length of 30cm (that’s a little less than 1ft) and a male pin that easily inserts into...

            Alligator Test Leads - Multicolored (10 Pack) Alligator Test Leads, Multicolored, alligator clips, prototyping, crocodile clips
            SF-PRT-12978
            Price: $2.95 In Stock
            Item #: SF-PRT-12978 -

              Alligator clips (or Crocodile clips, if you prefer) are likely to be the most useful thing on your workbench besides the workbench itself. Whether you’re just trying to make a few quick connections to test your circuit or having trouble making your multimeter leads stay where you need them, these spring-loaded clips are a workshop must-have. Each lead in this pack of tern is 50cm long with a rubber shrouded alligator clip on each end. There are five different colors, you get two each of: red,...

              Cold 2-Wire Splice (UY) - 10 pack cold, wire, splice, uy, crimp
              AF-1496
              Price: $2.95 In Stock
              Item #: AF-1496 -

                Get connected quickly with a Cold 2-Wire Splice (UY). These little wonders bite into any 22-26 AWG solid core wire with a quick squeeze from some parallel-jaw or slip joint pliers, making a solid butt splice connection. Though not waterproof, the splices contain silicone jelly to keep the cold splice from oxidizing.

                Cold Splice Wire Tap (UB) - 10 pack cold, wire, splice, ub, crimp
                AF-1494
                Price: $2.95 In Stock
                Item #: AF-1494 -

                  Get connected quickly with a Cold Splice Wire Tap (UB). These little wonders bite into any 22-26 AWG solid core wires with a quick squeeze from some parallel-jaw or slip joint pliers, making a solid 3-way splice connection. Though not waterproof, the splices contain silicone jelly to keep the cold splice from oxidizing.

                  USB 3.0 A to Micro B Cable - 1.5ft USB 3.0 A to Micro B Cable - 1.5ft, usb 3.0, usb 3.0 a, usb 3.0 a to micro b, usb micro b, usb charge cable
                  CBL-USBA2MICROB
                  Price: $2.95 In Stock
                  Item #: CBL-USBA2MICROB -

                    USB 3.0 A to Micro B cable.

                    Sparkfun Cerberus USB Cable Sparkfun Cerberus USB Cable, Sparkfun, Cerberus, USB, Cable, Robot, Data, mini, micro
                    SF-CAB-12016
                    Price: $5.95 In Stock
                    Item #: SF-CAB-12016 -

                      You are in the middle of working on your latest robot, when you need to program a new board you just got in. You dig through your bin of USB cables only to find that you have hundreds that have the wrong end, and exactly zero that have the end you're looking for. As luck would have it, you remember that you ordered the Sparkfun Cerberus USB Cable! With this cable, you will always have the right connection. The Cerberus USB Cable has the standard A-type connector, which you can plug into your...

                      Phidgets 12 foot Sensor Cable Phidgets 12 foot Sensor Cable, Phidget 12 foot Sensor Cable
                      PH-3004
                      Price: $3.00 In Stock
                      Item #: PH-3004 -

                        This is a 12-foot, 3-pin cable for connecting sensors to the analog inputs on the Phidgets 8/8/8 Interface Kit. This product is part of the Phidgets family! Phidgets are an easy to use set of USB-based building blocks for low cost sensing and control from your PC. A wide array of sensors, I/O devices, and controllers are available. To view the entire Phidgets product line, follow this link. Getting Started with Phidgets Phidgets Documentation: Manuals, data sheets, and tutorials for Phidgets...

                        RobotGeek Sensor Cable Pack robotgeek, robotgeek sensor pack, robotgeek sensor cable pack, robotgeek cable pack, servo wire, 2 pin jumpers, sensor squid, pin couplers, jr female, y cable, variety pack
                        RG-SPACK
                        Price: $24.95 In Stock
                        Item #: RG-SPACK -

                          The Robot Geek Sensor Cable Pack will hook you up with all your sensor and servo wiring needs and beyond. This variety cable pack includes: 3x 3 Pin Female to Female Y Cable 1x 32 Foot Standard Servo Wire 20x 3 Pin Sensor Cable 10x 2 Pin Dual-Female Jumper Wires (300mm) 10x Sensor Squids 25x 2-Pin Couplers 25x 3-Pin Couplers ...

                          Serial Cable - 6ft - 9-pin - Male/Female DB9 Cable, DB9, DB-9, RS232, RS-232 cable, RS232 cable
                          AC-100-14606
                          Price: $6.75 Back Order
                          Item #: AC-100-14606 -

                            This is a standard male-to-female serial cable. Great for connecting any serial device with a DB-9 connector to a PC.

                            Phidgets 24 Inch Sensor Cable Phidget 24 Inch Sensor Cable, Phidgets 24 Inch Sensor Cable
                            PH-3002
                            Price: $2.00 In Stock
                            Item #: PH-3002 -

                              This is a 24-inch, 3-pin cable for connecting sensors to the analog inputs on the Phidgets 8/8/8 Interface Kit. This product is part of the Phidgets family! Phidgets are an easy to use set of USB-based building blocks for low cost sensing and control from your PC. A wide array of sensors, I/O devices, and controllers are available. To view the entire Phidgets product line, follow this link. Getting Started with Phidgets Phidgets Documentation: Manuals, data sheets, and tutorials for Phidgets...

                              RobotGeek 150mm 3-pin Sensor Cable 10 pack
                              CBL-JRFEM150
                              Price: $4.95 In Stock
                              Item #: CBL-JRFEM150 -

                                RobotGeek Sensor Cables are for use with all RobotGeek sensors, shields, servos, and output devices. These cables are .1"(2.54mm) pitch and are 150mm in length with color coded wires. Add some 3-Pin Couplers to connect cables together for extension cables. These cables are also compatible with Phidgets Sensors and Electronic Brick Sensors, though they do not have the plastic buckle like traditional Phidgets/Electronic Brick Cables. ...

                                300mm 3-pin Female Sensor Cable 10 pack
                                CBL-JRFEM
                                Price: $4.95 In Stock
                                Item #: CBL-JRFEM -

                                  RobotGeek Sensor Cables are for use with all RobotGeek sensors, shields, servos, and output devices. These cables are .1"(2.54mm) pitch and are 300mm in length with color coded wires. Add some 3-Pin Couplers to connect cables together for extension cables. These cables are also compatible with Phidgets Sensors and Electronic Brick Sensors, though they do not have the plastic buckle like traditional Phidgets/Electronic Brick Cables. ...

                                  Servo Cable
                                  CBL-32SEN
                                  Price: $12.95 In Stock
                                  Item #: CBL-32SEN -

                                    Our 32 Feet Standard Servo Wire is great for repairing and extending servo and sensor cables. The Futaba Black-Red-White (Ground-Voltage-Signal) color scheme will help you keep your signals straight. This cable has 24awg stranded wire and no connectors on either end.

                                    LiPo/Li-ion Battery Wiring Harness battery, wiring, harness, power, dean plug, barrel plug, battery link, lipo battery harness, lipo harness
                                    CBL-HARNESS
                                    Price: $8.95 In Stock
                                    Item #: CBL-HARNESS -

                                      Easily link your project to a LiPo/Li-ion battery with the Battery Wiring Harness! This harness is the same one we use in our Hexapod and Quadruped kits. Just attach the male Dean connector to any of our LiPo/Li-ion Batteries and the barrel jack plug into your project, and you're ready to go! The harness even has a built in switch to quickly shut down power to your project. The switch is easily mountable - just cut a 6mm hole into your project and use the included nut and washer to securley...

                                      Sensor Y Cable - 100mm sensor Y cable, sensor splitter cable, servo y cable, servo splitter cable
                                      CBL-3PF2Y
                                      Price: $1.95 In Stock
                                      Item #: CBL-3PF2Y -

                                        The Sensor Y Cable is a great tool for splitting a single signal to multiple output boards. These cables are 100mm long and use a standard .1"/2.54mm pitch, making them compatible with RobotGeek I/O boards, Hobby servos, and breadboards. With this cable you can easily connect from a single output port on the RobotGeek Sensor Shield to a RobotGeek Relay, a RobotGeek LED Driver or a RobotGeek Buzzer. Combine this cable with 2 3-Pin Couplers to easily connect from 1 port to 2 Hobby Servos. You...

                                        Squid Cable
                                        CBL-SQUID
                                        Price: $4.95 In Stock
                                        Item #: CBL-SQUID -

                                          Sometimes you need to hook a servo or a sensor directly to your Arduino, or minimize the mess of jumper wires on your breadboard. These Squid Sensor Cables - 10 pack will help you do just that! On one end, you have a standard 3-pin connector (.1"/2.54mm pitch), and on the other end you have 3 single female jumper wires. You can easily position each cable exactly where you need it. and are 200mm in length. Add some 3-Pin Couplers to attach these cables directly to a servo or your arduino. These...

                                          3-Pin Couplers
                                          S-200-3P-Coupler-25pack
                                          Price: $2.95 In Stock
                                          Item #: S-200-3P-Coupler-25pack -

                                            You can use these 3 pin couplers to connect 3 pin jumper wires together and create your own extension wires. This is perfect for extending analog sensors or servos! You can also use them to make modular connectors on your breadboard/protoboard so that connecting to other components is even easier. The pins on these couplers are spaced at .1"/2.54mm, so they're compatible with Electronic Brick/Phidgets sensor cables, hobby servo cables, and most breadboards/protoboard. They are NOT compatible...

                                            4 Pin Sensor Cable 300mm 4 pin sensor cable, 4pin sensor cable, lcd sensor cable, lcd cable, 4pin cable, 4 pin cable, sensor cable
                                            CBL-4PINSEN
                                            Price: $1.95 In Stock
                                            Item #: CBL-4PINSEN -

                                              This standard 4 Pin Sensor Cable is 30cm long and has a .1"/2.54mm pitch, making it compatible with 4-pin sensors and shields. You can also add Pin Couplers and attach the cable to breadboards.

                                              RobotGeek 4 Pin Sensor Squid 300m 4 pin, sensor, cable, squid, data, 300m, jumper, breakout
                                              CBL-SQUID4P
                                              Price: $4.95 In Stock
                                              Item #: CBL-SQUID4P -

                                                Sometimes you need to hook a serial/I2C device directly to your Arduino, or minimize the mess of jumper wires on your breadboard. These 4 Pin Sensor Squid 300m cables will help you do just that! On one end, you have a standard 4-pin connector (.1"/2.54mm pitch), and on the other end you have 4 single female jumper wires. You can easily position each cable exactly where you need it. Each cable is 300m in length. Comes in pack of 10 squid cables. Pair these cables with 2-pin couplers to adapt...

                                                150mm Jumper Wires F/F (Set of 10)
                                                AC-200-PRT08430
                                                Price: $3.95 In Stock
                                                Item #: AC-200-PRT08430 -

                                                  These Jumper Wires F/F (Set of 10) are great for connecting male headers from one board to another. Combine them with Male Jumpers to make even longer cables! These jumpers will fit neatly into a .1" header, so they're great for bread boards. Each pack of 10 comes with cables in 5 colors. Each cable is 150mm long

                                                  2-Pin Couplers
                                                  S-200-2P-Coupler-25pack
                                                  Price: $2.95 In Stock
                                                  Item #: S-200-2P-Coupler-25pack -

                                                    You can use these 2 pin couplers to connect 2/4 pin jumper wires together and create your own extension wires. You can also use them to make modular connectors on your breadboard/protoboard so that connecting to other components is even easier. The pins on these couplers are spaced at .1"/2.54mm, so they're compatible with Electronic Brick/Phidgets sensor cables and most breadboards/protoboard. They are NOT compatible with Grove cables. ...

                                                    Electronic Brick - Fully Buckled 3 Wire Cable - 5 Pack
                                                    SEEED-ELB111C5M
                                                    Price: $4.99 In Stock
                                                    Item #: SEEED-ELB111C5M -

                                                      5 pack of fully buckled 3 wire cables for the Electronic Brick family of products.

                                                      Jumper Wires - Connected 6" (M/F, 20 pack)
                                                      SF-PRT-12794
                                                      Price: $1.95 In Stock
                                                      Item #: SF-PRT-12794 -

                                                        These are 6" long jumper wires terminated as male to female. Use these to jumper from any male or female header on any board. Multiple jumpers can be connected next to one another on a 0.1" header. Comes in one pack of 20 jumpers (colors shown). Each group of jumpers are connected to each other and can either be pulled apart in any quantity (from 1-20, of course) or kept whole based on you needs. These jumper wires can be used for pretty much everything! They work great with breadboards,...

                                                        Probe jumper wire – 8pcs
                                                        SS-CAB01101M
                                                        Price: $4.00 In Stock
                                                        Item #: SS-CAB01101M -

                                                          This is a 300mm jumper wire with probe, it is easy for connecting two point.

                                                          2 Pin Dual-Female Jumper Wire - 300mm - 10pcs pack 2 Pin, Dual, Female, Jumper, Wire, 300mm, cable
                                                          CBL-S-CAB103C4O
                                                          Price: $4.50 In Stock
                                                          Item #: CBL-S-CAB103C4O -

                                                            These 2 Pin Dual-Female Jumper Wire - 300mm - 10pcs pack are perfect for prototyping. Use them to run power from one breadboard rail to another, or use multiples to connect signals from one board to another. Each pack comes with 10 cables and each cable is 300mm long. The .1" pitch is great for standard breadboards.

                                                            9v Battery Snap Connect 9v, Battery, Snap, Connect, barrel, jack, cable, plug
                                                            CBL-9VSNP
                                                            Price: $2.95 In Stock
                                                            Item #: CBL-9VSNP -

                                                              The 9v Battery Snap Connect is the perfect companion to any 2.1*5.5mm female power jack. Whether you need to hook up to an Arduino/Geekduino Board, a Female Pigtail Lead or the AX/MX Power Hub, this cable has you covered. The tail is 10" long. Powering your project with a 9 volt battery has never been this easy. The 90 degree angle plug lets you hook up, even in tight spaces! ...

                                                              Premium USB to Micro USB Charge & Sync Cable - 6ft
                                                              CBL-USB2MICRO
                                                              Price: $6.95 In Stock
                                                              Item #: CBL-USB2MICRO -

                                                                This 6ft Micro USB Cable is perfect for powering and programming controllers like the RobotGeek Geekduino

                                                                DC Straight to 90 Cable DC Straight to 90 Cable, dc power cable, 90 degree power cable, straight to 90 degree power cable, dc 90 degree power cable
                                                                CBL-DC90CONV
                                                                Price: $3.95 In Stock
                                                                Item #: CBL-DC90CONV -

                                                                  Sometimes the size difference between a straight barrel plug and a 90° barrel plug determines whether or not a project will fit in an enclosure. Now with the DC Straight to 90 Cable you can easily convert straight barrel jacks to 90° jacks! Each cable is 20cm long and has a 2.1*5.5mm barrel jack, making it compatible with many of our power supplies and wiring harnesses.

                                                                  USB A Male to Mini B (5P) M - 6ft
                                                                  CBL-USBA2MINI
                                                                  Price: $4.95 In Stock
                                                                  Item #: CBL-USBA2MINI -

                                                                    Description This USB A plug to Mini 5 pin (one ID Pin) plug is designed for USB peripherals such as cellular phones, digital devices or PDA. Introduction: With much smaller than existing USB connectors, our 5 pin (one ID Pin) provides reliable host-to-peripherals connectivity for portable/hand-help PC architecture, cellular phones and other digital devices, such as, DSC and PDA. This product is fully compliant with USB 1.1 Standard Specification.

                                                                    90 Degree DC to Pigtail Cable 90, Degree, DC, Pigtail, Cable, barrel, jack
                                                                    CBL-90PIGTAIL
                                                                    Price: $3.95 In Stock
                                                                    Item #: CBL-90PIGTAIL -

                                                                      The 90 Degree DC to Pigtail Cable is the perfect companion to any 2.1*5.5mm female power jack. Whether you need to hook up to an Arduino/Geekduino Board, a Female Pigtail Lead or the AX/MX Power Hub, this cable has you covered. The tail is 10" long and splits easily. Marked side negative, unmarked positive. The 90 degree angle plug lets you hook up, even in tight spaces! ...

                                                                      Large Bread Board
                                                                      SS-STR102C2B
                                                                      Price: $8.50 In Stock
                                                                      Item #: SS-STR102C2B -

                                                                        Ah the bread board, unsung hero of the DIY electronics movement. How many circuits started as a tangle of wires on a breadboard? How many noted professionals got their start wiring on a breadboard? Well now you can keep the tradition alive with the Large Bread Board. The bread board is made up of rows upon rows of holes, waiting to be wired up with circuitry. Each row(terminal strip) is wired together to make it easy for you to wire up circuits. The Large Bread Board also has 4 columns(bus...

                                                                        USB A Male to A Male USB, A, Male, to, USB A Male
                                                                        CBL-USBA2A
                                                                        Price: $5.95 In Stock
                                                                        Item #: CBL-USBA2A -

                                                                          The USB A Male to A Male cable is a strange one. With a USB A Male plug on each end, this cable allows you to hook up USB devices in non-standard ways. If you need it, you know.

                                                                          DC Squid Cable dc squid cable, squid cable, dc squid, squid cable female to male, female to male squid, 1 female to 6 male dc cable
                                                                          CBL-DCSQUID
                                                                          Price: $9.95 In Stock
                                                                          Item #: CBL-DCSQUID -

                                                                            Do you want to attach multiple devices to a single power supply, but don't want to splice and solder them all together? Then check out the DC Squid Cable. With this cable you can plug up to 6 devices up to one DC power supply. For example, you could connect 6 Arduino boards up to one power supply. Each barrel jack connector is 2.1*5.5mm. making it compatible with out many power supplies and wiring harnesses. Please keep in mind that it is up to the user to determine that the power supply can...

                                                                            Medium Bread Board
                                                                            SS-STR101C2M
                                                                            Price: $5.50 In Stock
                                                                            Item #: SS-STR101C2M -

                                                                              Sometimes half the board is just as useful! The Medium Bread Board is perfect for prototyping smaller circuits, or for mounting directly onto projects. The bread board is made up of rows upon rows of holes, waiting to be wired up with circuitry. Each row(terminal strip) is wired together to make it easy for you to wire up circuits. The Large Bread Board also has 4 columns(bus strips) wired together, to use to easily connect power to any individual terminal strip. Specifications 60 terminal...

                                                                              Barrel Jack Male Pigtail Lead 2.1*5.5*12mm barrel jack male, pigtail lead, power cable, cable, pigtail power,
                                                                              CBL-PIGTAIL
                                                                              Price: $2.95 In Stock
                                                                              Item #: CBL-PIGTAIL -

                                                                                The Barrel Jack Male Pigtail Lead 2.1*5.5*12mm is the perfect companion to any 2.1*5.5mm female power jack. Whether you need to hook up to an Arduino/Geekduino Board, a Female Pigtail Lead or the AX/MX Power Hub, this cable has you covered. The tail is 10" long and splits easily.

                                                                                Mini Bread Board
                                                                                SS-STR118C2M
                                                                                Price: $2.95 In Stock
                                                                                Item #: SS-STR118C2M -

                                                                                  Whether you're using it to prototyping tiny circuits, or daisy-chaining hundreds of them together, the Mini Bread Board is a great tool to have around. With it's tiny form factor, you can keep a couple in your car, your overnight bag, or just about anywhere life might take you. This breadboard also has an adhesive backing. This, combined with it's size, makes it a great last-minute junction for cabling on any project with a due date. Just press thie breadboard on your project, finish your...

                                                                                  Barrel Jack Female Pigtail Lead 2.1 - 5.5mm Barrel Jack Female Pigtail Lead 2.1 - 5.5mm
                                                                                  CS-CT5089
                                                                                  Price: $2.95 In Stock
                                                                                  Item #: CS-CT5089 -

                                                                                    Are you tired of cutting the ends off your AC to DC power supplies? Yeah, so were we. So we sourced these awesome barrel jack pigtails. Now you can quickly power up to terminal blocks or solder these to your homemade switch harnesses and not molest your power supplies. The tail is 10" long and splits easily. Yes, you are welcome.

                                                                                    Female Dean to Female Barrel Plug Cable female dean, female barrel plug, power cable, cable
                                                                                    CBL-FDEANFBA
                                                                                    Price: $3.95 In Stock
                                                                                    Item #: CBL-FDEANFBA -

                                                                                      LiPo batteries are great for building robots, but using them to power your cralwer during development can be problamatic. Instread, use the Female Dean to Female Barrel Plug Cable to connect your robot to a DC power supply. Just plug the 2.1*5.5 female barrel jack into any of our SMPS Power supplies and the female dean connector into yor project and you'll be able to test for long streches without having to recharge your battery. Keep in mind that LiPo batteries can source alot of current, so...

                                                                                      T Connector Male-Female Pair Deans, Ultra, Plug, Battery, Connector, T, Male, Female
                                                                                      C-200-925
                                                                                      Price: $2.99 In Stock
                                                                                      Item #: C-200-925 -

                                                                                        These are generic connectors similar to the popular Deans Ultra Plug connectors. They are sold as matching male-female pairs and have a current rating of 50 A. Perfect for use in high current draw applications and one of the most widely used connector types for Lithium Polymer (LiPo) Battery Packs.

                                                                                        Panel Mount Dual Power Cable arduino panel mount jack, panel mount power cable
                                                                                        CBL-RBPLUG
                                                                                        Price: $6.95 In Stock
                                                                                        Item #: CBL-RBPLUG -

                                                                                          This Panel Mount Dual Power Cable is great for adding a external jack to any Arduino enclosure like the Project Box For Arduino. This cable splits from the single female DC jack (2.1*5.5mm) into a male DC jack (also 2.1*5.5) as well as two .1"/2.54mm pitch female jumper cables. The male DC jack will plug into most Arduino boards, leaving the extra power cables available for motors, relays, and more!

                                                                                          GP2D12 - Sharp IR Sensor to Servo Cable
                                                                                          RC-IR_Cable
                                                                                          Price: $1.95 In Stock
                                                                                          Item #: RC-IR_Cable -

                                                                                            This cable adapts from the JST connector found on the Sharp IR sensors to a standard 3-pin servo-style connector.  This is compatible with many robot controller boards, such as those used in the Robonova and KHR humanoids.

                                                                                            Phidgets USB Isolator phidgets, Phidgets USB Isolator, USB Isolator, Isolator
                                                                                            PH-3060
                                                                                            Price: $58.25 In Stock
                                                                                            Item #: PH-3060 -

                                                                                              Product Features Protects your PC from overvoltage Increases system stability Protects from overvoltages up to 1kV USB speed selectable Product Description The USB Isolator is designed to protect your PC from harmful voltage that can flow from devices attached to your PC through the USB cable. The isolator is inserted between the Phidgets board and your PC. The USB Isolator can also be used to eliminate problems caused by ground “voltage” differences between USB Host and USB...

                                                                                              AX/MX Power Hub 3/4 view
                                                                                              IL-4PHUB
                                                                                              Price: $7.95 In Stock
                                                                                              Item #: IL-4PHUB -

                                                                                                The 6 Port RX/EX Power Hub is a must have accessory for any DYNAMIXEL user working with 4-pin servos.  The DYNAMIXEL communication bus allows you to daisy chain multile servos, making wiring a breeze. However sometimes you need to split your DYNAMIXEL chain into multiple directions. Just plug a 4-Pin Dynamixel Cable from your controller to any port on the hub, and you'll have 5 ports available for DYNAMIXEL's 4-pin servos. This hub has the added benefit of 2 power breakouts. You can plug...

                                                                                                150mm Jumper Wires M/M (Set of 10)
                                                                                                AC-200-PRT08431
                                                                                                Price: $3.95 In Stock
                                                                                                Item #: AC-200-PRT08431 -

                                                                                                  These Jumper Wires M/M (Set of 10) are great for connecting female headers from one board to another. Combine them with FeMale Jumpers to make even longer cables! These jumpers will fit neatly into a .1" header, so they're great for bread boards. Each pack of 10 comes with cables in 5 colors. Each cable is 150mm long