The RobotGeek system is a platform for learning about and building your own Arduino Inventions. All of the RobotGeek hardware and electronic components are designed to be modular, allowing you to easily configure, customize, reconfigure and build your project. You can start with our RobotGeek Experimenter's Kits and Robot Kits or build your own custom project form the ground up. We even have a wide variety of open source demo code and tutorials to help you learn about programming your Arduino compatible microcontroller.

The RobotGeek System is so easy to use for three reasons: a unified mounting system, easy wiring, and the Arduino platform.

Learn More!


Imax B6 Multi-Function LiPo Balance Charger Imax, B6, Multi-Function, Balance, Charger, LiPo, Lithium, Polymer
Price: $34.95
Availability: In Stock
Trossen Robotics Item #: P-BC-IMAXB6 -

The IMAX B6 is an advanced multi-function charger, able to charge, balance and discharge Lion, LiPo, LiFe (A123), NiCd and NiMH batteries. It can also be used to charge Lead Acid (Pb) batteries. It has a wide variety of voltage settings for charging various cell count batteries, as well as a 0.1 amp adjustable charge rate of up to 5 amps. To use this charger with our line of Thunder Power LiPos, you will need an E-Flite Balance Charger Adapter Cable Pack. This charger requires an 11-18v input...

Phidgets 12 foot Sensor Cable Phidgets 12 foot Sensor Cable, Phidget 12 foot Sensor Cable
Price: $3.00
Availability: In Stock
Phidgets Inc Item #: PH-3004 -

This is a 12-foot, 3-pin cable for connecting sensors to the analog inputs on the Phidgets 8/8/8 Interface Kit. This product is part of the Phidgets family! Phidgets are an easy to use set of USB-based building blocks for low cost sensing and control from your PC. A wide array of sensors, I/O devices, and controllers are available. To view the entire Phidgets product line, follow this link. Getting Started with Phidgets Phidgets Documentation: Manuals, data sheets, and tutorials for Phidgets...

RFIDuino Shield V1.2 Arduino RFID Shield, RFID Arduino, Arduino RFID, RFID Shield for Arduino, Arduino EM4102, Arduino RFID reader, V1.2
Price: $17.50-$34.95
Availability: In Stock
RobotGeek Item #: RG-RFIDUINO -

This page is for the RFIDuino V1.2. Visit this guide to see the differences between the Version 1.1 and 1.2 Hardware. The RFIDuino is an Arduino RFID Shield which makes Arduino RFID projects super easy to build. Just drop the RFIDuino Shield onto your Arduino microcontroller, load our sample code, and you'll be reading tags in no time! Our getting started guide will take you through the process of working with the RFIDuino from loading basic code to more advanced projects like triggering...

RFIDuino Wireless Upgrade Kit Wireless RFID, Xbee RFID,
Price: $76.95
Availability: In Stock
RobotGeek Item #: KIT-RFIDUINO-W-KT -

The RFIDunio Wireless Communication Starter Kit provides everything you need to harness the powerful and versatile technology of Zigbee wireless communication and free your RedBee from wires. Perfect for remote installations, mobile platforms, or any application where 'cutting' the USB cable to your PC is convenient.   [2x] XBee 1mW Communication Module This is the very popular 2.4GHz XBee module from Digi. These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a...

RobotGeek 180 Degree Robot Servo robot servo, 180 degree robot servo, robotgeek servo, robotgeek robot servo, robotgeek 180 degree servo, 180 degree servo
Price: $24.95
Availability: In Stock
RobotGeek Item #: ASM-RGS-13 -

Get ready to bring your robotic dreams to life with the RobotGeek 180 Degree Robot Servo! This metal-geared servo is perfect for building robotic joints and will help you create your own custom robotic arms, crawlers, and more! And because these servos use a standard PWM signal for control, they're easy to directly interface with microcontrollers like the Arduino! RobotGeek Servo by RobotGeek on Sketchfab Idler Horn The difference between a regular servo and robot servo is the Idle Horn. This...

RobotGeek Geekduino
Price: $22.50
Availability: In Stock
RobotGeek Item #: RG-GEEKDUINO -

The Geekduino is the new Arduino Compatible board from RobotGeek! This board goes into every RobotGeek Robot Kit and is the perfect microcontroller for your next robotic project! The Geekduino uses the ubiquitous Micro USB port to power and program the board. The Geekduino can also be powered via the ultra low-profile flat DC power jack. A series of switches allows you to toggle on/off the Geekduino's FTDI reset (handy for software projects) as well as change the operating voltage of the...

RobotGeek 150mm 3-pin Sensor Cable 10 pack
Price: $4.95
Availability: In Stock
RobotGeek Item #: CBL-JRFEM150 -

RobotGeek Sensor Cables are for use with all RobotGeek sensors, shields, servos, and output devices. These cables are .1"(2.54mm) pitch and are 150mm in length with color coded wires. Add some 3-Pin Couplers to connect cables together for extension cables. These cables are also compatible with Phidgets Sensors and Electronic Brick Sensors, though they do not have the plastic buckle like traditional Phidgets/Electronic Brick Cables. ...

RobotGeek Continuous Rotation Servo robotgeek 360 degree robot servo, robotgeek continuous servo, robotgeek robot servo, robot servo, robotgeek servo, continuous robot servo, continuous servo,Continuous Rotation
Price: $24.95
Availability: In Stock
RobotGeek Item #: ASM-RGS-4C -

Get ready to bring your robotic dreams to life with the RobotGeek Continuous Rotation Servo! This metal-geared servo is perfect for building robotic rovers, spinners and more! And because these servos use a standard PWM signal for control, they're easy to directly interface with microcontrollers like the Arduino! Idler Horn The difference between a regular servo and robot servo is the Idle Horn. This horn will spin freely and is at the opposite position of the main drive horn. The idler horn...

RobotGeek Sensor Shield ( Version 2 ) RobotGeek Sensor Shield, V2, Version 2, Arduino Sensor Shield, Scratch Sensor Shield, Arduino Bricks, Arduino Sensors, Arduino Motors, Arduino Starter Kit
Price: $7.95
Availability: In Stock
RobotGeek Item #: RG-SENSHIELDV2 -

The Arduino Platform is a great way for learning about electronics and programming, as well as creating microcontoller based projects. But even simple projects can get messy very quickly, leaving you with a pile of wires, breadboards, and components. With the RobotGeek Sensor System, you can put your project on the fast track and get it up and running in no time. The RobotGeek Sensor Shield will fit on any Standard Arduino Compatible board*, and break out the digital and analog pins into easy...

RS2-550 Motor - 12V
Price: $11.95
Availability: In Stock
RobotGeek Item #: MOT-550 -

This is a Mabuchi RS-550 motor with a 3-pole balanced armature. Motor Specifications   Performance Operating v : 6v - 14.4v Nominal v : 12v No Load RPM : 18000 No Load A : 1.2A Stall Torque : 70.55 oz-in 498.2 mN-m Stall Current : 85A Kt : 0.83 oz-in/A 5.9 mN-m/A Kv : 1608 rpm/V Efficiency : 70% RPM - Peak Eff : 17250 Current - Peak Eff : 10A Physical Weight : 7.7 oz (218g) Length - for motor : 2.24 in (57mm) Diameter (with flux ring) : 1.52 in (38.5mm) Diameter (no flux ring) : 1.41 in...

GP2D12 Alternative IR Distance Sensor Kit (10-80 cm) - 1 sensor GP2D12 Alternative IR Distance Sensor Kit (4-30 Inch) - 1 sensor
Price: $23.70
Availability: In Stock
Trossen Robotics Item #: KIT-S-10-P1101KT -

One of the most favored IR range sensors on the market. Detects distances from 4" to 30" (10cm-80cm). Note: The sensor sold here is actually a Sharp IR GP2Y0A21YK0F. It has the same distance range as a GP2D12 and very similar analog output properties. The GP2D12 is extremely difficult to source currently, so these sensors provide a great alternative. For more information on the minor differences, please refer to the datasheets for each sensor: Datasheets GP2D12 Datasheet GP2Y0A21YK0F...

300mm 3-pin Female Sensor Cable 10 pack
Price: $4.95
Availability: In Stock
RobotGeek Item #: CBL-JRFEM -

RobotGeek Sensor Cables are for use with all RobotGeek sensors, shields, servos, and output devices. These cables are .1"(2.54mm) pitch and are 300mm in length with color coded wires. Add some 3-Pin Couplers to connect cables together for extension cables. These cables are also compatible with Phidgets Sensors and Electronic Brick Sensors, though they do not have the plastic buckle like traditional Phidgets/Electronic Brick Cables. ...

GP2Y0A02YK IR Sensor Kit   (20-150 cm) - 1 sensor
Price: $25.75
Availability: In Stock
Trossen Robotics Item #: KIT-S-10-GP2Y0A02YKT -

This Phidget IR Distance Sensor Kit includes everything you need to add a Sharp GP2Y0A02YK distance sensor to the 8/8/8 Interface Kit.Kit includes: GP2Y0A02YK IR Sensor (20-150 cm / 8-60 inches) Phidget IR Distance Sensor Interface Board 12" Sharp GP2D12 Cable This product is part of the Phidgets family! Phidgets are an easy to use set of USB-based building blocks for low cost sensing and control from your PC. A wide array of sensors, I/O devices, and controllers are available. To view the...

Power Supply 6VDC 2.0A - US Power Supply 6VDC 2.0A, Power Supply, 6VDC, 2 amp
Price: $9.95
Availability: In Stock
Top Power Co Item #: POW-6v2a -

Power Supply for general project use.North American Style Plug6VDC, 2 Amp, Center Positive Polarity, 5.5x2.1MM

RG90 Gear Motor RG90 Gear Motor, MOT-VIB08, Gear Motor, gearmotor, 6v gearmotor, 90rpm, 1:120, Arduino Motor, Robot Motor
Price: $5.95
Availability: In Stock
RobotGeek Item #: MOT-VIBO8 -

Weighing in at just 35 grams, this RG90 Gear Motor can put put an impressive 1.2 kg/cm of torque! That makes it great for small, wheeled robots! The double-flat output shaft is 7mm in diameter and is perfect for attaching to our Gear Motor Wheel. Our gear motors come with two- 300mm wires pre-soldered onto the motor. Each wire is terminated with a 2.54mm female connector. This makes them ideal for attaching to any 2.54mm pin connector. ...

1-8S LiPo Battery Voltage Tester/Monitor LiPo Battery Tester, LiPo Battery Monitor, Battery Monitor, 1-8s
Price: $12.95
Availability: In Stock
KoKo Technology Ltd Item #: VOLT-TESTER -

Managing your LiPo battery is a must. If you let your battery get to low you can diminish the capacity of your battery or even render it unusable. That's where our 1-8S LiPo Battery Voltage Tester/Monitor comes in. First, this unit can be used to test your battery's voltage. It will display the total voltage of your battery, then cycle through and display the voltage of each individual cell. Secondly, the unit will monitor your battery and sound an alarm when one if its cells falls below a...

7v5A Power Supply
Price: $11.95
Availability: In Stock
Item #: POW-7v5A -

7VDC, 5 Amp Power Supply for general project use. Center Positive Polarity, 5.5x2.1MM barrel jack.

3-Pin Couplers
Price: $2.95
Availability: In Stock
Palyoo Industrial LTD Item #: S-200-3P-Coupler-25pack -

You can use these 3 pin couplers to connect 3 pin jumper wires together and create your own extension wires. This is perfect for extending analog sensors or servos! You can also use them to make modular connectors on your breadboard/protoboard so that connecting to other components is even easier. The pins on these couplers are spaced at .1"/2.54mm, so they're compatible with Electronic Brick/Phidgets sensor cables, hobby servo cables, and most breadboards/protoboard. They are NOT compatible...

RobotGeek Pushbutton arduino pushbutton, arduino button, arduino button board, arduino digital button
Price: $2.95
Availability: In Stock
RobotGeek Item #: ASM-RG-PUSHBUTTON -

The RobotGeek Pushbutton is a self-contained Arduino Button board that makes it easy to add a pushbutton to your Arduino Project. This RobotGeek Pushbutton has a built in pull-down resistor, so the signal can be read as a digital input from your Arduino or other microcontroller. This Arduino Button Board has the standard RobotGeek three pin connection so it plugs right into the RobotGeek Sensor Shield to get you up and running immediatly. As with all RobotGeek sensors, the hole mounting...

RobotGeek 12v Mini Self-Priming Pump
Price: $17.95
Availability: In Stock
RobotGeek Item #: RG-SMPUMP -

If you are looking for an Arduino Pump the RobotGeek small liquid and air pump is a great solution. This pump is self priming so it can be used for projects involving plant watering, suction, drainage, drink dispensing, barbots, and more. To use this for an Arduino Pump project all you need is a RobotGeek Relay and seperate power supply. The pump can operate at either 6 or 12 volts and packs a punch in a small package! Recommended Arduino Pump Tutorials: Arduino ShotBot Project Arduino Pump...

RobotGeek Rotation Knob arduino rotation knob, arduino rotation sensor, arduino knob sensor, arduino knob control, arduino rotation control
Price: $4.95
Availability: In Stock
RobotGeek Item #: ASM-RG-ROTKNOB -

Do you need Rotation Knobs for your Arduino project? The RobotGeek Knob is good choice! It has the standard RobotGeek three pin connection so it plugs right into the RobotGeek Sensor Shield to get you up and running immediatly. As with all RobotGeek sensors, the hole mounting pattern is on a 1x1 CM grid so they easily mount to the RobotGeek Workbenches or any other RobotGeek kit. Each sensor includes a mounting plate and all hardware needed to mount to any workbench or RobotGeek product that...

140mm Slewing Bearing slewing bearing, robot slewing bearing, robot arm base bearing
Price: $19.95
Availability: In Stock
RobotGeek Item #: RW-140BEARING -

The 140mm Slewing Bearing is the same bearing found in our Robotic Arms. Each bearing is made of a soft aluminum alloy and sports a single row of spherical bearings. These bearings give the bearing a silky smooth movement, perfect for assisting your robotic arm base, or just about any other moving joint. The slewing bearing goes great with the Standoff Variety Pack and the Nut and Bolt Variety Pack, giving you all the hardware you need to attach the bearing to a variety of projects. ...

2-Pin Couplers
Price: $2.95
Availability: In Stock
Palyoo Industrial LTD Item #: S-200-2P-Coupler-25pack -

You can use these 2 pin couplers to connect 2/4 pin jumper wires together and create your own extension wires. You can also use them to make modular connectors on your breadboard/protoboard so that connecting to other components is even easier. The pins on these couplers are spaced at .1"/2.54mm, so they're compatible with Electronic Brick/Phidgets sensor cables and most breadboards/protoboard. They are NOT compatible with Grove cables. ...

Solenoid Valve arduino Solenoid valve, arduino solenoid water valve, solenoid liquid valve, arduino solenoid valve, arduino water valve, arduino liquid valve
Price: $19.95
Availability: In Stock
RobotGeek Item #: HW-WVALVE -

If you are looking for an Arduino solenoid valve the RobotGeek liquid solenoid valve is a perfect solution. Compact with mounting holes make it a great fit for DIY projects of all kinds. The Solenoid Valve is a great companion to the Large DC Liquid Pump and the Small DC Liquid Pump. When building pumping projects sometimes it is necessary to add a valve to stop either liquid back draw or unwanted flow. When using diaphram pumps if your liquid supply is higher than your pouring point, pressure...

2 Pin Dual-Female Jumper Wire - 300mm - 10pcs pack 2 Pin, Dual, Female, Jumper, Wire, 300mm, cable
Price: $4.50
Availability: In Stock
Seeed Studio Item #: CBL-S-CAB103C4O -

These 2 Pin Dual-Female Jumper Wire - 300mm - 10pcs pack are perfect for prototyping. Use them to run power from one breadboard rail to another, or use multiples to connect signals from one board to another. Each pack comes with 10 cables and each cable is 300mm long. The .1" pitch is great for standard breadboards.

RobotGeek Joystick arduino joystick, arduino analog joystick, arduino joystick sensor, arduino joystick potentiometer
Price: $5.95
Availability: In Stock
RobotGeek Item #: ASM-RG-JOYSTICKV2 -

If you are looking for a good Arduino Joystick the RobotGeek Joystick is the best choice. We had these joysticks special made two joystick options; the standard mushroom top used in gaming controllers and a tall stick for much greater range of motion. The joystick has the standard RobotGeek three pin connection and plugs right into the RobotGeek Sensor Shield so you can be up and running immediatly. This arduino joystick is self centering and will return to the home position when let go. The...

120mm Slewing Bearing slewing bearing, robot slewing bearing, robot arm base bearing
Price: $19.95
Availability: In Stock
RobotGeek Item #: RW-120BEARING -

The 120mm Slewing Bearing is the smaller version of the 140mm slewing bearing found in our Robotic Arms. Each bearing is made of a soft aluminum alloy and sports a single row of spherical bearings. These bearings give the bearing a silky smooth movement, perfect for assisting your robotic arm base, or just about any other moving joint. The slewing bearing goes great with the Standoff Variety Pack and the Nut and Bolt Variety Pack, giving you all the hardware you need to attach the bearing to a...

medium solenoid
Price: $14.95
Availability: In Stock
RobotGeek Item #: ASM-SOL-MD -

If you are looking for a solenoid for your DIY, educational, or Arduino solenoid project the RobotGeek solenoids are a great choice. This is the Medium version of the solenoid line with a plunger travel of 7mm and up to 1800 g/3.97 lbs lbs of force. (View the specifications tab for full information.) If you want to control this solenoid from your Arduino all you need is to add a RobotGeek Relay and power source and you have an Arduino Solenoid project! Check out our Arduino Solenoid Tutorial...

Robot Geek 4C battery pack Robot Geek 4C battery pack
Price: $7.95
Availability: In Stock
RobotGeek Item #: ASM-4CBATPAC -

The Robot Geek 4C Battery Holder comes with a mounting plate and convenient 90 degree barrel plug to save space. The mounting bracket conforms to the Robot Geek 1 X 1 CM grid allowing you to mount your battery pack anywhere you like on your projects!

Premium USB to Micro USB Charge & Sync Cable - 6ft
Price: $6.95
Availability: In Stock
RobotGeek Item #: CBL-USB2MICRO -

This 6ft Micro USB Cable is perfect for powering and programming controllers like the RobotGeek Geekduino

RobotGeek Tilt Sensor arduino tilt sensor, tilt sensor, arduino digital tilt senor, arduino tilt senor board
Price: $4.95
Availability: In Stock
RobotGeek Item #: ASM-RG-TILTSEN -

The RobotGeek Tilt Sensor is a fast and flexible way to add an Arduino tilt senor Project. By reading this sensor as a digital input, you can determine if an object the sensor is mounted on tilted or not. This sensor is unique because of the orientation of its ports. Instead of having the tilt switch soldered into the board, there are two 2-pin female ports. This allows you to orient your tilt vertically or horizontally to suit your project best. If you need your tilt switch to be further away...

small solenoid
Price: $9.95
Availability: In Stock
RobotGeek Item #: ASM-SOL-SM -

If you are looking for a solenoid for your DIY, educational, or Arduino solenoid project the RobotGeek solenoids are a great choice. This is the Medium version of the solenoid line with a plunger travel of 5mm and up to 700 g/1.54 lbs lbs of force. (View the specifications tab for full information.) If you want to control this solenoid from your Arduino all you need is to add a RobotGeek Relay and power source and you have an Arduino Solenoid project! Check out our Arduino Solenoid Tutorial...

RobotGeek Temperature Sensor RobotGeek, Temperature, temp, Sensor, thermometer, environment
Price: $6.95
Availability: In Stock
RobotGeek Item #: ASM-RG-TEMP -

Want to make your project kick into gear when life turns up the heat? The RobotGeek Temperature Sensor can feel its way through! With the 3-pin Sensor Cable standard, you can easily connect this to your project and start reading the temperature! Use it to activate your air conditioner, control the temperature in a cold frame, log the temperature of a greenhouse, or to monitor the temperature of a pie on the windowsill! The options are limitless and the temperature is accounted for. As with all...

USB A Male to A Male USB, A, Male, to, USB A Male
Price: $5.95
Availability: In Stock
Item #: CBL-USBA2A -

The USB A Male to A Male cable is a strange one. With a USB A Male plug on each end, this cable allows you to hook up USB devices in non-standard ways. If you need it, you know.

DC Squid Cable dc squid cable, squid cable, dc squid, squid cable female to male, female to male squid, 1 female to 6 male dc cable
Price: $9.95
Availability: In Stock
InterbotiX Item #: CBL-DCSQUID -

Do you want to attach multiple devices to a single power supply, but don't want to splice and solder them all together? Then check out the DC Squid Cable. With this cable you can plug up to 6 devices up to one DC power supply. For example, you could connect 6 Arduino boards up to one power supply. Each barrel jack connector is 2.1*5.5mm. making it compatible with out many power supplies and wiring harnesses. Please keep in mind that it is up to the user to determine that the power supply can...

RobotGeek Light Sensor robotgeek light sensor, photocell, light sensor, robotgeek, arduino light sensor, arduino photocell
Price: $3.95
Availability: In Stock
RobotGeek Item #: ASM-RG-LIGHT -

This RobotGeek Light Sensor is an analog sensor that will allow you to measure light from your Arduino or other microcontroller. The more light the sensor detects, the higher the your analog port will detect. Each RobotGeek Light Sensor comes with a dual female-female jumper cable so that you can move the light sensor off the board. This makes placing your sensors easier than ever. You can use this sensor to measure the ambient light in a room, or to measure the relative brightness of...

RobotGeek Buzzer arduino buzzer, arduino buzzer board, arduino speaker, arduino piezo, arduino piezo board
Price: $3.95
Availability: In Stock
RobotGeek Item #: ASM-RG-BUZZER -

Get buzzing with this Arduino Buzzer! The RobotGeek Buzzer is an easy way to add audio output to your Arduino. By simply sending a 5v signal to the RobotGeek Buzzer, the device will emit a tone. You can also use the Arduino Tone Function to send different tones to the buzzer. NOTE:some frequencies will work better than others with this piezo buzzer. This Arduino Buzzer has the standard RobotGeek three pin connection so it plugs right into the RobotGeek Sensor Shield to get you up and running...

10x 100mm Aluminum M3 Standoff F/F 100mm, metal, Aluminum, M3, Standoff, F/F, female to female, female, 10cm
Price: $6.95
Availability: In Stock
RobotGeek Item #: ASM-FF100 -

Need to make a really tall robot? Not enough horizontal space on your workbench and you want to expand vertically? Is your Geekbot tall, but not quite imposing enough? With the 100mm Aluminum M3 Standoff F/F, you can add a whopping 10 centimeters in height to your project. Made of solid Aluminum these are light and strong, giving you a sturdy mounting point for any project! This pack includes eight Standoffs, which is enough to make your geekbot, snapper, or turret taller. ...

10x 100mm Aluminum M3 Standoff M/F 100mm, metal, Aluminum, M3, Standoff, M/F, male to female, male, female, extension
Price: $6.95
Availability: In Stock
RobotGeek Item #: ASM-MF100 -

Need to make a really tall robot? Not enough horizontal space on your workbench and you want to expand vertically? Is your Geekbot tall, but not quite imposing enough? With the 100mm Aluminum M3 Standoff M/F, you can add a whopping 10 centimeters in height to your project. Made of solid Aluminum these are light and strong, giving you a sturdy mounting point for any project! This pack includes eight Standoffs, which is enough to make your geekbot, snapper, or turret taller. With the male end,...

RobotGeek Voltage Divider RobotGeek Voltage Divider, Robot Geek Voltage Divider, Voltage Divider, FSR Voltage Divider, Force Sensitive Resistor Voltage Divider, FSR Interface, FSR Analog Interface
Price: $4.95
Availability: In Stock
RobotGeek Item #: ASM-RG-VOLTDIV -

The RobotGeek Voltage Divider is a simple yet effective way to turn a variable resistor, such as an FSRs, Softpots, or Pressure Sensors into a tunable 0-5v analog signal. The design is super simple and completely open source, but saves tinkerers from having to breadboard a potentiometer of their own. A 2 position terminal block and 0.1" spaced header are available for sensor input, a 3 pos right angle header breaks out Analog output, 5v input, and Gnd. Each sensor includes necessary...

FSR Kit Combo
Price: $32.25
Availability: In Stock
RobotGeek Item #: KIT-S-20-1000-FSRKT -

This kit comes with everything you need to hook your Force Sensing Resistor into your microcontroller or Phidgets Interface Kit. Connect the FSR to the voltage divider board using the 2-Pin female cable, or with the terminal adaptor. Then feed the voltage divider power and ground through the 3-pin cable, and you'll get an analog voltage reading on the third pin of that cable. Check out this video and the videos below for more info. The FSR in this kit is perfect for robotic grippers, robot...

.2 Inch FSR Kit force sensor
Price: $14.35
Availability: In Stock
RobotGeek Item #: KIT-S-20-1000-FSRKT2 -

This kit comes with everything you need to hook your Force Sensing Resistor into your microcontroller or Phidgets Interface Kit. Connect the FSR to the voltage divider board using the 2-Pin female cable, or with the terminal adaptor. Then feed the voltage divider power and ground through the 3-pin cable, and you'll get an analog voltage reading on the third pin of that cable. Check out this video and the videos below for more info. The FSR in this kit is perfect for robotic grippers, robot...

.5 Inch FSR Kit force sensor
Price: $14.95
Availability: In Stock
RobotGeek Item #: KIT-S-20-1000-FSRKT5 -

This kit comes with everything you need to hook your Force Sensing Resistor into your microcontroller or Phidgets Interface Kit. Connect the FSR to the voltage divider board using the 2-Pin female cable, or with the terminal adaptor. Then feed the voltage divider power and ground through the 3-pin cable, and you'll get an analog voltage reading on the third pin of that cable. Check out this video and the videos below for more info. The FSR in this kit is perfect for robotic grippers, robot...

1.5 Inch FSR Kit force sensor
Price: $16.25
Availability: In Stock
RobotGeek Item #: KIT-S-20-1000-FSRKT15 -

This kit comes with everything you need to hook your Force Sensing Resistor into your microcontroller or Phidgets Interface Kit. Connect the FSR to the voltage divider board using the 2-Pin female cable, or with the terminal adaptor. Then feed the voltage divider power and ground through the 3-pin cable, and you'll get an analog voltage reading on the third pin of that cable. Check out this video and the videos below for more info. The FSR in this kit is perfect for robotic grippers, robot...

Clear Silicone Tubing 3.5mm clear silicone tubing, food tubing, food safe tubing, silicone tube, safe clear tube, clear tube, clear tubing, food, safe
Price: $19.95
Availability: In Stock
RobotGeek Item #: RAW-TUBING -

If you're looking for a food safe silicone tube solution for our DC Liquid Pump or Water Valve, or a better alternative to standard US 1/8" tubing? We've got it! Our silicone tubing comes in 10 meter rolls! We've sourced this tubing to make sure that it easily fits onto our pump and solenoid, but it still strong enough to stay on.Please note, our silicone tubing is not rated by the FDA or USDA.

Rubber Bumpers - Large rubber bumpers, large rubber bumpers, rubber feet, large rubber feet
Price: $4.95
Availability: In Stock
RobotGeek Item #: ASM-12-RW-KSH0433 -

Large Rubber Bumpers are great for any project! Whether you need some traction on the bottom of your project or a little more clearance for nuts bolts and wires underneath your project, these bumpers will do the job. These bumpers have an adhesive backing that makes them easy to attach to any surface. Bumpers are 20mm*20mm on the larger face (this face has the adhesive backing) , 14mm*14mm on the smaller/bottom face and 9mm tall. Each pack comes with 12 individual bumpers. ...

Wii Classic Controller Kit Wii, Classic, Controller, Kit, joystick, robot, geek, robotgeek
Price: $14.95
Availability: In Stock
RobotGeek Item #: CON-WII-KIT -

The Wii Classic Controller Kit is a great addition to any robotics project requiring direct control. With only 4 pins you get a total of 15 digital buttons and 4 analog inputs (2 joysticks). This is great for controlling robot movement as well as setting parameters, modes and more! Our comprehensive Getting Started Guide will show you how to hook up the board/controller and how to use our Arduino Library for the controller. A video posted by Trossen Robotics (@trossenrobotics) on Dec 2, 2015...