Whether you've got a crawler, biped or rover, you're going to need a battery pack to get your robot moving on its own. Lithium Polymer batteries are a great choice for robot batteries because they have great capacity-to-weight ratios, giving you lots of power for very little weight. Our 3s 11.1V 2200mAh 30C LiPo Battery is a great medium sized battery that can discharge up to 66A continously! To make it easy to connect/disconnect the battery from your project, each of these batteries has a...

Whether you've got a crawler, biped or rover, you're going to need a battery pack to get your robot moving on its own. Lithium Polymer batteries are a great choice for robot batteries because they have great capacity-to-weight ratios, giving you lots of power for very little weight. Our 3s 11.1V 900mAh 25C LiPo Battery is a great small sized battery that can discharge up to 22.5A continously! To make it easy to connect/disconnect the battery from your project, each of these batteries has a...

The AnyVolt 3 Universal DC-DC Converter is an adjustable step up / step down 3A switching regulator. The output is adjustable from 3 to 24V. The output voltage is set with a small screw potentiometer on the back of the AnyVolt 3. Once the output voltage is set, it does not matter whether input voltage is higher, lower, or the same as the desired output. The potential applications are endless and only limited by the unit's specifications and your collection of gadgets that require DC power at a...

Add colored lighting to your projects with some electroluminescent (EL) wire! Available in 5 different colors (red, yellow, blue, green and white). Each coil is a very thin 2.3 mm in diameter and 3 meters long. In a dark room, these are very bright! They're easy to bend, hang and shape to fit your needs. EL wire works best at 120V AC. So, to use this product, you must power it through a DC to AC inverter. The inverter converts 3.3 V DC from your Arduino to AC. It will not work off of DC power...

Whether you've got a crawler, biped or rover, you're going to need a battery pack to get your robot moving on its own. Lithium Polymer batteries are a great choice for robot batteries because they have great capacity-to-weight ratios, giving you lots of power for very little weight. Our 3s 11.1V 4500mAh 35C LiPo Battery is a great medium sized battery that can discharge up to 66A continously! To make it easy to connect/disconnect the battery from your project, each of these batteries has a...

The GP2Y0A41SK0F IR Sensor Kit will easily allow you to attach the Sharp IR Distance Sensor GP2Y0A41SK0F to Phidgets Interface Kits with Analog Inputs, like the 8/8/8 kit and 2/2/2 kit The Sharp IR Distance Sensor GP2Y0A41SK0F is a great low cost robotic range-finder. The Distance Sensor will report the presence of an object 4-30cm away from the sensor. The sensors reports this data as an analog value readable by most microcontrollers, like the Arduino. Includes: Sharp IR Distance Sensor...

This simple little Logic Level Converter will let you easily interface 5v and 3.3v devices. With this board you can step up a 3.3v signal to 5v, or down from 5 to 3.3. This is great when you need to connect 5v sensors/microcontrollers to ARM based devices like the Arduino Due or Raspberry Pi. You can even solder standard headers to this board to make it breadboard compatible. The level converter is very easy to use. The board needs to be powered from the two voltages sources (high voltage and...

Product Features Sends and Receives Consumer IR codes Control your computer or any Phidgets with an old remote control Control your TV, DVD, etc. with your computer Connects directly to a computer's USB Port Product Description You can use the PhidgetIR to control devices with remote control input - such as your TV or DVD player, from your computer by having the PhidgetIR transmit remote control codes. Your application can learn the signals from arbitrary remote controls. The learned code can...

Product Description The Phidget GPS provides the longitude and latitude of the board's position in signed decimal degree format. The position accuracy (best case) is 2.5m CEP (Circular Error of Probability). The 1040 also provides altitude, heading and velocity as well as the time and date. It will also let you know when it has a satellite fix. The PhidgetGPS has a 3V rechargeable lithium battery to provide "hot starts" by remembering its previous positions. With a live battery, the 1040 can...

Product Description The 1049 - PhidgetSpatial 0/0/3, a 3 axis Accelerometer, measures static and dynamic acceleration in 3 axes, up to 5g, and provides a high sampling speed of up to 1000 samples per second. Each accelerometer axis is calibrated at the factory for cross-axis misalignment, sensitivity to positive and negative acceleration, and offset. Product Specifications Characteristic Value Acceleration Bandwidth @ 1ms sample rate 110Hz Measurement Range (XYZ Axis ±5g (49 m/s2) Acceleration...

Product Description The 1056 - PhidgetSpatial 3/3/3, 9 Axis IMU (Inertial Measurement Unit) measures static and dynamic acceleration in 3 axes, up to 5g.; it also measures magnetic field in 3-axes up to ±4 Gauss and finally measures angular rotation in 3 axes, up to ±400° per second. With the 1056, you are getting a lot more than 3 sensor chips slapped on a board. The 1056 has been rigorously tested to ensure that the output data correlates to physical real life motion, instead of relying...

The Sharp IR Distance Sensor GP2Y0A41SK0F is a great low cost robotic range-finder. The Distance Sensor will report the presence of an object 4-30cm away from the sensor. The sensors reports this data as an analog value readable by most microcontrollers, like the Arduino. This sensor can plug directly into a RobotGeek Sensor Shield using a Sharp IR to Servo Cable. This cable can also be handy to connect to other systems and controllers (users can cut/splice the wire). If you want to use this...

The SN74HC165N is a neat little IC that will take an input of up to 8 parallel lines and produce a single, serial output. It’s a great way to increase the number of inputs on a microcontroller. This breakout makes it easy to prototype using the 74HC165 by breaking out all of the pins you need to standard 0.1" spaced headers. We’ve also lined up the data and power pins so that you can easily make chains of them and expand the number of outputs under your control! This chip works with a voltage...

It is a standard USB A to B cable. It is 6 feet long. It has gold plated connectors. Not much else to say. Buy one if you need it. Or don't. It won't hurt our feelings honestly.

Parallax has designed a USB to Serial (RS-232) adapter that is compact and economical to provide a Virtual Com Port for all of our products that have a DB9 (9-pin) serial connector. Cable included. Updated FTDI USB drivers for Windows are included in the latest versions of the BASIC Stamp Editor, Propeller Tool, and SX-Key IDE software packages. You may also download the Windows drivers separately from our site, or drivers for other operating systems directly from FTDI (see the Downloads...

The PIR(Passive Infra-Red) Sensor is a pyroelectric device that detects motion by sensing changes in the infrared(radiant heat) levels emitted by surrounding objects.Each Wide Angle PIR Sensor cable includes a 4-pin cable, as well as a mount and hardware to adapt to all RobotGeek products with a centimeter grid pattern (Workbenches, Geekbot, etc.). Mount it at a right angle, and flat.Product FeaturesSingle bit output Small size On-board LEDs Power 3V to 6VDC operation 150uA idle, 3mA active(no...

The Arduino Uno R3 is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Uno differs from all...

Dynamixel Comparison Guide The MX-28T Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and up to 3mpbs using the new TTL 2.0 bus. Each servo has the ability to track its speed, temperature, shaft position, voltage, and load. As if this weren't enough, the newly implemented PID control algorithm used to maintain shaft position can be...

Dynamixel Comparison Guide The MX-28AT Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and up to 3mpbs using the new TTL 2.0 bus. Each servo has the ability to track its speed, temperature, shaft position, voltage, and load. As if this weren't enough, the newly implemented PID control algorithm used to maintain shaft position can...

Dynamixel Comparison Guide The MX-28R Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and up to 3mpbs using the new RS-485 2.0 bus. Each servo has the ability to track its speed, temperature, shaft position, voltage, and load. As if this weren't enough, the newly implemented PID control algorithm used to maintain shaft position can...

Dynamixel Comparison Guide The MX-28AR Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and up to 3mpbs using the new RS-485 2.0 bus. Each servo has the ability to track its speed, temperature, shaft position, voltage, and load. As if this weren't enough, the newly implemented PID control algorithm used to maintain shaft position...

Dynamixel Comparison Guide The MX-64T Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and up to 3mpbs using the new TTL 2.0 bus. Each servo has the ability to track its speed, temperature, shaft position, voltage, and load. As if this weren't enough, the newly implemented PID control algorithm used to maintain shaft position can be...

Dynamixel Comparison Guide The AX-12A servo actuator from Robotis is the most advanced actuator on the market in this price range and has become the defacto standard for the next generation of hobby robotics. The AX-12A robot servo has the ability to track its speed, temperature, shaft position, voltage, and load. As if this weren't enough, the control algorithm used to maintain shaft position on the ax-12 actuator can be adjusted individually for each servo, allowing you to control the speed...

Dynamixel Comparison Guide The MX-64AT Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and up to 3mpbs using the new TTL 2.0 bus. Each servo has the ability to track its speed, temperature, shaft position, voltage, and load. As if this weren't enough, the newly implemented PID control algorithm used to maintain shaft position can...

Dynamixel Comparison Guide The AX-18A servo actuator from Robotis is the next step up from the hugly popular AX-12A Servo, offering nearly twice the speed and 15% more torque! The AX-18A robot servo retains the formfactor and all of the same features of its predecessor: the ability to track its speed, temperature, shaft position, voltage, and load. As if this weren't enough, the control algorithm used to maintain shaft position on the AX-18A actuator can be adjusted individually for each...

Dynamixel Comparison Guide The MX-64R Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and up to 3mpbs using the new RS-485 2.0 bus. Each servo has the ability to track its speed, temperature, shaft position, voltage, and load. As if this weren't enough, the newly implemented PID control algorithm used to maintain shaft position can...

The MX-12W from ROBOTIS is the Goldilocks of servos; everything about it is just right. It has the compact size of the AX-12A and AX-18A (and uses the same housing) yet has the electronics and control capabilities of the high performance MX servos like the MX-28T and MX-64T. This is the only servo at this size and cost, that is capable of true position control for multiple rotations. If you've ever tried to get more than one revolution out of your servo and been frustrated with losing your...

Dynamixel Comparison Guide The MX-64R Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and up to 3mpbs using the new RS-485 2.0 bus. Each servo has the ability to track its speed, temperature, shaft position, voltage, and load. As if this weren't enough, the newly implemented PID control algorithm used to maintain shaft position can...

Dynamixel Comparison Guide The AX-12W servo actuator from Robotis is a wheeled variant of the popular AX-12A. Essentially this servo is an AX-12A with a lower gear ratio so that a much higher RPM can be achieved, making it ideal for use in 'Wheel Mode' as opposed to the traditional 'Joint Mode'. The AX-12W robot servo has the ability to track its temperature, voltage, and load. As if this weren't enough, the control algorithm used to maintain shaft position on the ax-12 actuator can be...

Dynamixel Comparison Guide The MX-106T Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and up to 3mpbs using the new TTL 2.0 bus. Each servo has the ability to track its speed, temperature, shaft position, voltage, and load. As if this weren't enough, the newly implemented PID control algorithm used to maintain shaft position can...

Dynamixel Comparison Guide The MX-106R Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and up to 3mpbs using the new RS-485 2.0 bus. Each servo has the ability to track its speed, temperature, shaft position, voltage, and load. As if this weren't enough, the newly implemented PID control algorithm used to maintain shaft position...

The XL-320 servo from ROBOTIS is so small you might mistake it for an ordinary hobby servo, but you would be missing out! Despite its diminutive size, it is actually one of the newest models in the DYNAMIXEL robot servo line from ROBOTIS. Each XL-320 can produce up to 0.39 N-m (55 in-oz) of torque and rotate at 114 RPM in precisely controlled 0.29° increments. For its size (24 x 36 x 27 mm) and weight (16.7 g) there is no other servo that can compete with the XL-320 in performance and...

Dynamixel Comparison Guide This is a 6 piece Bulk package of the MX-28T. In this bulk pack, the servos are bare and do not come with the required servo horn, nor any additional cables, brackets, or hardware. If you need this hardware, it must be purchased separately. The MX-28T Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and up...

Dynamixel Comparison Guide This is a 6 piece Bulk package of the MX-28T. In this bulk pack, the servos are bare and do not come with the required servo horn, nor any additional cables, brackets, or hardware. If you need this hardware, it must be purchased separately. The MX-28AT Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and...

Dynamixel Comparison Guide This is a 6 piece Bulk package of the MX-28R. In this bulk pack, the servos are bare and do not come with the required servo horn, nor any additional cables, brackets, or hardware. If you need this hardware, it must be purchased separately. The MX-28R Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and up...

Dynamixel Comparison Guide This is a 6 piece Bulk package of the MX-64T. In this bulk pack, the servos are bare and do not come with the required servo horn, nor any additional cables, brackets, or hardware. If you need this hardware, it must be purchased separately. The MX-64T Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and up...

Dynamixel Comparison Guide This is a 6 piece Bulk package of the MX-64T. In this bulk pack, the servos are bare and do not come with the required servo horn, nor any additional cables, brackets, or hardware. If you need this hardware, it must be purchased separately. The MX-64AT Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and...

The DYNAMIXEL PRO line of Robot Actuators is ROBOTIS's new solution for full-scale robots. These new actuators have incredibly high power and precision, making them ideal for for everything from advanced robotics to industry applications. Using ROBOTIS's frame system for the DYNAMIXEL PRO, you'll be able to rapidly create a variety of different systems and robots. These new servos have position, speed, AND torque based commands. The L42-10-S300-R uses a RS-485 communication protocol, a 300:1...

Dynamixel Comparison Guide This is a 6 piece Bulk package of the MX-64AR. In this bulk pack, the servos are bare and do not come with the required servo horn, nor any additional cables, brackets, or hardware. If you need this hardware, it must be purchased separately. The MX-64AR Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and...

Dynamixel Comparison Guide In this bulk pack, the servos are bare and do not come with the required servo horn, nor any additional cables, brackets, or hardware. If you need this hardware, it must be purchased separately.The MX-106T Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and up to 3mpbs using the new TTL 2.0 bus. Each...

Dynamixel Comparison Guide This is a 6 piece Bulk package of the MX-106R. In this bulk pack, the servos are bare and do not come with the required servo horn, nor any additional cables, brackets, or hardware. If you need this hardware, it must be purchased separately.The MX-106R Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and...

The DYNAMIXEL PRO line of Robot Actuators is ROBOTIS's new solution for full-scale robots. These new actuators have incredibly high power and precision, making them ideal for for everything from advanced robotics to industry applications. Using ROBOTIS's frame system for the DYNAMIXEL PRO, you'll be able to rapidly create a variety of different systems and robots. These new servos have position, speed, AND torque based commands. The M42-10-S260-R uses a RS-485 communication protocol, a 260:1...

The DYNAMIXEL PRO line of Robot Actuators is ROBOTIS's new solution for full-scale robots. These new actuators have incredibly high power and precision, making them ideal for for everything from advanced robotics to industry applications. Using ROBOTIS's frame system for the DYNAMIXEL PRO, you'll be able to rapidly create a variety of different systems and robots. These new servos have position, speed, AND torque based commands. The M54-40-S250-R uses a RS-485 communication protocol, a 250:1...

The DYNAMIXEL PRO line of Robot Actuators is ROBOTIS's new solution for full-scale robots. These new actuators have incredibly high power and precision, making them ideal for for everything from advanced robotics to industry applications. Using ROBOTIS's frame system for the DYNAMIXEL PRO, you'll be able to rapidly create a variety of different systems and robots. These new servos have position, speed, AND torque based commands. The M54-60-S250-R uses a RS-485 communication protocol, a 250:1...

The DYNAMIXEL PRO line of Robot Actuators is ROBOTIS's new solution for full-scale robots. These new actuators have incredibly high power and precision, making them ideal for for everything from advanced robotics to industry applications. Using ROBOTIS's frame system for the DYNAMIXEL PRO, you'll be able to rapidly create a variety of different systems and robots. These new servos have position, speed, AND torque based commands. The H42-20-S300-R uses a RS-485 communication protocol, a 300:1...

The DYNAMIXEL PRO line of Robot Actuators is ROBOTIS's new solution for full-scale robots. These new actuators have incredibly high power and precision, making them ideal for for everything from advanced robotics to industry applications. Using ROBOTIS's frame system for the DYNAMIXEL PRO, you'll be able to rapidly create a variety of different systems and robots. These new servos have position, speed, AND torque based commands. The H54-100-S500-R uses a RS-485 communication protocol, a 500:1...

The DYNAMIXEL PRO line of Robot Actuators is ROBOTIS's new solution for full-scale robots. These new actuators have incredibly high power and precision, making them ideal for for everything from advanced robotics to industry applications. Using ROBOTIS's frame system for the DYNAMIXEL PRO, you'll be able to rapidly create a variety of different systems and robots. These new servos have position, speed, AND torque based commands. The H54-200-S500-R uses a RS-485 communication protocol, a 500:1...

The ArbotiX-M Robocontroller is at the heart of every Interbotix Robot. This versatile robot controller is an advanced control solution for BIOLOID and DYNAMIXEL based actuators. As an Arduino compatible microcontroller the Arbotix Robocontroller also benefits from a huge open source community of libraries and examples. Since its release in 2010 the Arbotix has quickly become a favorite among builders worldwide from hobby to high level research. The 'M' in ArbotiX-M stands for mini - this new...

Package Contents:Components                QuantityBlack 2 Step45White 2 Step22Green 2 Step12Blue 2 Step12Yellow 2 Step12Orange 2 Step6Grey 3 Step12

The Wireless SD Shield provides a 3.3v regulated Digi Xbee slot for easy wireless connectivity, a uSD (micro Secure Digital) slot for onboard storage capabilities, and a compact prototyping board area for custom additions. Transmission LED indicator lights, a reset button, and serial select switch are also available for your convenience. Passthrough headers allow for additional Shields to be stacked on top.More information available soon!

The XYZrobot A1-16 Smart Servo is modular actuator, which combines a gear reducer, a DC motor and an embedded control board in one small package. The servo motor provides the necessary torque to operate a small robot. An added function of the motors is to provide information about internal temperature, supply voltage, current and display operational status through an LED.The A1-16 Smart Servo is compatible with the AX line of brackets from Robotis, please refer to the cables found here. (3 Pin...

The Xevelabs USB2AX v3.2a USB to TTL Dynamixel Servo Interface is diminutive in size, but talks a big game with any device utilizing a half-duplex TTL interface 3-pin connector using the Dynamixel Protocol! The USB2AX works as a serial device, receiving messages from your PC via USB, and transmitting the data over to the DYNAMIXEL chain. You can send and read data to/from DYNAMIXEL servos just like you would with a microcontroller. Often a USB2DYNAMIXEL adapter would be used to connect a PC to...

This is a super mini voltmeter with 0.28 inch LED display. It has reverse connect protection (though it is advisable to mind your wiring). When voltage is less than 10V, two decimal places will be shown. When voltage is more than 10V, one decimal place will be shown. This voltmeter would be great for a battery readout on your next robot, or generally useful for a retro readout panel!

The 1.3" OLED Module is a fantastic screen for your next project! With a resolution of 128x64, it is suitable for applications displaying text, images, and more! What is OLED? OLED (Organic Light-Emitting Diode) is a self light-emitting technology composed of a thin- multi-layered organic film placed between an anode and cathode. In contrast to LCD technology- OLED does not require a backlight. OLED possesses high application potential for virtually all types of displays and is regarded as the...

With this 2.1mm DC Barrel Jack to Alligator Clips cable you can easily turn a wall adapter into a power supply! A high quality molded 2.1mm DC barrel jack is brought out to red (center positive) & black (ring negative) alligator clips. Works with most wall adapters. Good for 2-3 Amps and up to 24VDC.

This 2.1mm DC Barrel Plug to Alligator Clips cable can turn any battery pack into a power supply in a snap! A high quality molded 2.1mm DC barrel plug is brought out to red (center positive) & black (ring negative) alligator clips. Good for 2-3 Amps of current, up to 24VDC. 2.1mm is near standard for electronics, and fits the Geekduino splendidly.

This is a 4.8-46V, 2A Dual Motor Controller which is the revised version of the DF-MDV1.0. Its performance has been improved greatly. It can bear larger current due to the increased heatsink dissipation. It is easy to control, using LGS's outstanding high-power motor driver chip, the L298N. This chip allows for direct drive of two bi-directional DC motors, and incorporates high-speed short diodes for protection. Drive current up to 2A per motor output. The driver uses a broad-brush design to...

The Arduino product family is a great learning platform for electronics, programming and robotics, but most projects at some point require mobility. The 2A Motor Shield For Arduino allows for motor control with Arduino right away! Stack up this shield on your controller and drive motors with higher power requirements. Depending on the motor of choice, you can make it fast or handle a higher payload. This Arduino Compatible Motor Shield (2A) uses L298P chip which allow to drive two 7-12V DC...

This pack of 5 5mm Plastic Bevel LED Holder will keep your LEDs in place. Made of the ever ubiquitous black plastic, with a subtle bevel that gracefully leans into the curve of your LED, people will take notice of your great taste in flush mounting hardware.

Need to plug in a USB device, but it's just out of reach? Have a short USB cable with a proprietary connector? The 6' USB Extension cable is what you need! This cable has a standard USB A male connector on one end, and a standard USB A female connector on the other, allowing you to extend the reach of virtually any USB cable in your arsenal.

A BEC (battery elimination circuit) is a great tool for getting a lower voltage from a higher voltage system. For example, say you needed 6v to drive a RobotGeek servo on your 11.1v PhantomX Hexapod , but you didn't want to add a secondary battery just for the 6v servo. Simply plug this BEC into your Hexapod's battery and you'll get a stable 6v 3A power supply. The 6v 3a UBEC 2-5S Lipoly (6-32v) is a small and lightweight UBEC, featuring a High efficiency switch mode design that provides...

10 pack of 4 pin cable for the XYZRobot A1-16 servo motor, 100mm length.

10 pack of 4 pin cable for the XYZRobot A1-16 servo motor, 150mm length.

10 pack of 4 pin cable for the XYZRobot A1-16 servo motor, 200mm length.

10 pack of 4 pin cable for the XYZRobot A1-16 servo motor, 250mm length.

10 pack of 4 pin cable for the XYZRobot A1-16 servo motor, 65mm length.

Want to make a hexapod walker? Maybe you're making a piece of art with tons of moving parts, or you need to drive a ton of LEDs with precise PWM output. Your microcontroller has a limited number of PWM outputs, and you find yourself running out! Not with the Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface. With this pwm and servo driver breakout, you can control 16 free-running PWM outputs with just two pins! Need to run more than 16 PWM outputs? No problem. Chain together up to 62...

Alligator clips (or Crocodile clips, if you prefer) are likely to be the most useful thing on your workbench besides the workbench itself. Whether you’re just trying to make a few quick connections to test your circuit or having trouble making your multimeter leads stay where you need them, these spring-loaded clips are a workshop must-have. Each lead in this pack of tern is 50cm long with a rubber shrouded alligator clip on each end. There are five different colors, you get two each of: red,...

The Analog Feedback Micro Servo may appear to be a normal micro servo, but it is so much more. What makes this little fella special? Beyond the metal gears which keep this servo solid for the long haul in hobby systems, this servo has feedback via a potentiometer wiper on a separate wire that can be read with an analog input, such as those on an Arduino, to get the servo's position. This gives you the ability to "record" the servo's motion, or improve stability.

The Arbotix-Pro Programming Kit contains an ST-Link/V2 USB Programmer and Olimex JTAG cable adapter. This programming kit is intended for advanced users only, custom programming of the Arbotix-Pro is not covered under technical support and is at the user’s own risk. Improper usage can permanently brick or destroy your Arbotix-Pro. Please pay attention to the orientation of the programming cable as improper orientation will destroy the board. The ST-LINK/V2 is an in-circuit debugger and...

Have you ever wanted to hook up your robot to your iOS device? Now you can utilize Bluetooth 4.0 Low Energy (BLE) technology in your robot with the BLE Mini. The BLE Mini requires only a serial port for communication so it supports all major development platforms that have UART interface including Arduino, ArbotiX-M Robocontroller, Geekduino, Raspberry Pi, etc. In addition, you are given access to all Ti's CC2540 I/O pins and the ability to upload firmware via USB, making the BLE Mini an ideal...

It's time to get Bluetooth 4.0 into your project and sync it up with your phone with the Bluno! For aficionados of smart devices and wearables, now you can go further and start prototyping with BLE integrated with your Arduino. Bluno is first of its kind in integrating BT 4.0 (BLE) module into Arduino Uno, making it an ideal prototyping platform for both software and hardware developers to go BLE. You will be able to develop your own smart bracelet , smart pedometer and more. Through the...

Get connected quickly with a Cold 2-Wire Splice (UY). These little wonders bite into any 22-26 AWG solid core wire with a quick squeeze from some parallel-jaw or slip joint pliers, making a solid butt splice connection. Though not waterproof, the splices contain silicone jelly to keep the cold splice from oxidizing.

Get connected quickly with a Cold Splice Wire Tap (UB). These little wonders bite into any 22-26 AWG solid core wires with a quick squeeze from some parallel-jaw or slip joint pliers, making a solid 3-way splice connection. Though not waterproof, the splices contain silicone jelly to keep the cold splice from oxidizing.

The Crash sensor (Left) is a miniature snap-action switch, also trademarked and frequently known as a micro switch. It is an electric switch that is actuated by very little physical force. Micro switches are very widely used; among their applications are appliances, machinery, industrial controls, vehicles, and many other places for control of electrical circuits. They are usually rated to carry current in control circuits only, although some switches can be directly used to control small...

The Crash sensor (Right) is a miniature snap-action switch, also trademarked and frequently known as a micro switch. It is an electric switch that is actuated by very little physical force. Micro switches are very widely used; among their applications are appliances, machinery, industrial controls, vehicles, and many other places for control of electrical circuits. They are usually rated to carry current in control circuits only, although some switches can be directly used to control small...

■ Basic Features U2D2 is a small size USB communication converter that enables to control and to operate the DYNAMIXEL with the PC. It is smaller than the previous model and has mount holes to make it easier to install on robots. It uses the USB cable to connect to the PC and prevents damage of the USB terminals. It has both 3Pin connectors for TTL communication and 4Pin connectors for RS-485 communication embedded for easier control and access for the Dynamixel X series. (Supports UART as...

he DYNAMIXEL XH430-V210-R is a High Performance RS-485 Servo in the DYNAMIXEL X-Series. Using the Same form factor as the other 430 series servos in the X-Series line, the DYNAMIXEL XH430-V210-R falls between the XH430-W210 and XM430-W210 in Speed and Torque, making it a well balanced servo for anything requiring speedy movement and enough strength to back it up. ...

he DYNAMIXEL XH430-V350-R is a High Performance RS-485 Servo in the DYNAMIXEL X-Series. Using the Same form factor as the other 430 series servos in the X-Series line, the DYNAMIXEL XH430-V350-R has a high Stall Torque rating, making it suitable for robots that need strength more than they need speed. DYNAMIXEL XH430-V350-R Model Number XH430-V350-R Weight (g) 82g Dimensions (mm) 28.5mm x 46.5mm x 34mm Gear Ratio 353.5 : 1 Operation Voltage (V) 24 Stall Torque (N.m) 3.3 Stall Current (A) 0.7...

he DYNAMIXEL XH430-W210-R is a High Performance RS-485 Servo in the DYNAMIXEL X-Series. Using the Same form factor as the other 430 series servos in the X-Series line, the DYNAMIXEL XH430-W210-R has a well balanced Stall Torque versus Speed rating, making it suitable for a wide variety of robotic tasks. DYNAMIXEL XH430-W210-R Model Number XH430-W210-R Weight 82g Dimension 28.5mm x 46.5mm x 34mm Gear Ratio 212.6 : 1 Operation Voltage (V) 11.1 12 14.8 Stall Torque (N.m) 2.2 2.5 3.1 Stall Current...

he DYNAMIXEL XH430-W210-T is a High Performance TTL Servo in the DYNAMIXEL X-Series. Using the Same form factor as the other 430 series servos in the X-Series line, the DYNAMIXEL XH430-W210-T has a well balanced Stall Torque versus Speed rating, making it suitable for a wide variety of robotic tasks. DYNAMIXEL XH430-W210-T Model Number XH430-W210-T Weight (g) 82g Dimensions (mm) 28.5mm x 46.5mm x 34mm Gear Ratio 212.6 : 1 Operation Voltage (V) 11.1 12 14.8 Stall Torque (N.m) 2.2 2.5 3.1 Stall...

he DYNAMIXEL XH430-W350-R is a High Performance RS-485 Servo in the DYNAMIXEL X-Series. Using the Same form factor as the other 430 series servos in the X-Series line, the DYNAMIXEL XH430-W350-R has a high Stall Torque and low RPM rating, making it well suited for robotic tasks requiring precision movement over speed. DYNAMIXEL XH430-W350-R Model Number XH430-W350-R Weight (g) 82 Dimensions (mm) 28.5 x 46.5 x 34 Gear Ratio 353.5 : 1 Operating Voltage (V) 11.1 12 14.8 Stall Torque (N.m) 3.1 3.4...

he DYNAMIXEL XH430-W350-T is a High Performance TTL Servo in the DYNAMIXEL X-Series. Using the Same form factor as the other 430 series servos in the X-Series line, the DYNAMIXEL XH430-W350-T has a high Stall Torque and low RPM rating, making it well suited for robotic tasks requiring precision movement over speed. DYNAMIXEL XH430-W350-T Model Number XH430-W350-T Weight (g) 82g Dimensions (mm) 28.5mm x 46.5mm x 34mm Gear Ratio 353.5 : 1 Operation Voltage (V) 11.1 12 14.8 Stall Torque (N.m) 3.1...

he DYNAMIXEL XL430-W250-T is the best TTL servo for your budget. With best-in-class Speed and Strength, as well as the 430 Series chassis structure, this servo handles your robot's needs with ease and doesn't put a dent in your wallet. DYNAMIXEL XL430-W250-T Model Name XL430-W250-T Weight (g) 57.2 Dimension (mm) 28.5 x 46.5 x 34 Gear Ratio 258.5 : 1 Operation Voltage (V) 9.0 11.1 12.0 Stall Torque (N.m) 1.0 1.4 1.5 Stall Current (A) 1.0 1.3 1.4 No Load Speed (RPM) 47 57 61 MCU ST CORTEX-M3...

he DYNAMIXEL XM430-W210-R is a High Performance RS-485 Servo in the DYNAMIXEL X-Series. Using the Same form factor as the other 430 series servos in the X-Series line, the DYNAMIXEL XM430-W210-R has the highest RPM rating in the 430 series in the X-Series line, making it well suited for robotic tasks requiring the highest speed. DYNAMIXEL XM430-W210-R Model Number XM430-W210-R Weight 82g Dimension 28.5mm x 46.5mm x 34mm Gear Ratio 212.6 : 1 Operation Voltage (V) 11.1 12 14.8 Stall Torque (N.m)...

he DYNAMIXEL XM430-W210-T is a High Performance TTL Servo in the DYNAMIXEL X-Series. Using the Same form factor as the other 430 series servos in the X-Series line, the DYNAMIXEL XM430-W210-T has the highest RPM rating in the 430 series in the X-Series line, making it well suited for robotic tasks requiring the highest speed. DYNAMIXEL XM430-W210-T Model Number XM430-W210-T Weight (g) 82g Dimensions (mm) 28.5mm x 46.5mm x 34mm Gear Ratio 212.6 : 1 Operation Voltage (V) 11.1 12 14.8 Stall...

he DYNAMIXEL XM430-W350-R is a High Performance RS-485 Servo in the DYNAMIXEL X-Series. Using the Same form factor as the other 430 series servos in the X-Series line, the DYNAMIXEL XM430-W350-R has the highest Torque rating in the 430 series in the X-Series line, making it well suited for robotic tasks requiring strength. DYNAMIXEL XM430-W350-R Model Number XM430-W350-R Weight 82g Dimension 28.5mm x 46.5mm x 34mm Gear Ratio 353.5 : 1 Operation Voltage (V) 11.1 12 14.8 Stall Torque (N.m) 3.8...

he DYNAMIXEL XM430-W350-T is a High Performance TTL Servo in the DYNAMIXEL X-Series. Using the Same form factor as the other 430 series servos in the X-Series line, the DYNAMIXEL XM430-W350-T has the highest Torque rating in the 430 series in the X-Series line, making it well suited for robotic tasks requiring strength. DYNAMIXEL XM430-W350-T Model Number XM430-W350-T Weight (g) 82g Dimensions (mm) 28.5mm x 46.5mm x 34mm Gear Ratio 353.5 : 1 Operation Voltage (V) 11.1 12 14.8 Stall Torque...

This is an Arduino compatible Fingerprint Sensor. With the high speed DSP processor, it could also work with other serial devices, such as MSP430, 51, AVR, PIC, STM32, ARM and FPGA. This fingerprint module can work alone without any principal computer or any PC software. It can store up to 1000 fingerprints. Supports fingerprint entry, intelligent image processing, fingerprint comparison and fingerprint search mode. It also has a high sensitivity to both wet and dry fingerprint recognition....

Product Description The 1120 FlexiForce Adapter makes it easy to interface a Tekscan FlexiForce Force Sensor to your PC. Just use the cable included with the adapter. We even give you a round plastic disc for the sensing pad. The FlexiForce sensor is an ultra-thin and flexible printed circuit, which can be easily integrated into most applications. With its paper-thin construction, flexibility and force measurement ability, the FlexiForce force sensor can measure force between almost any two...

The Analog Capacitive Soil Moisture Sensor measures soil moisture levels by capacitive sensing, rather than resistive sensing like other types of moisture sensor. It is made of a corrosion resistant material, giving it a long service life. Insert it into soil and impress your friends with the real-time soil moisture data! The product includes an on-board voltage regulator which gives it an operating voltage range of 3.3 ~ 5.5V. It is compatible with low-voltage MCUs (both 3.3V and 5V logic)....

The Analog Sound Sensor is typically used in detecting the volume of ambient noise. You could make a really fancy clapper with this, or use it for any number of projects to display sound levels! Features: Allows voltage supply of 3.3V or 5V Standard assembling structure (two 3mm holes with multiple of 5cm as interval) Easy to recognizes sensor interface ("A" for analog and "D" for digital) Icons to simply illustrate sensor function High quality connector Immersion gold surface ...

The Analog UV Sensor V2 with GUVA-S12SD chip is suitable for detecting the UV radiation in sunlight. It can be used in UV Index Monitoring, DIY project, UV-A Lamp Monitoring, Plants growing, Environmental monitoring, etc. It can detect the UV wavelength of 200-370nm with a quick response, linear analog voltage signal output. Small size, easy to install. With the diagram of the world health organization UV index grading standards, you can know the UV index from the sensor directly....

This DHT11 Temperature and Humidity Sensor is powerful and easy to use! The DHT11 has a full range temperature compensation, low power consumption, long term stability and calibrated digital signal. A high-performance 8-bit microcontroller is integrated in the sensor with calibration-coefficient saved in OTP memory to provide accurate temperature readings. Reliable and inexpensive with plenty of documentation and projects online. Features: Standard assembling structure (two 3mm holes with...

Are you tired of your old clicky pushbuttons? Check out the Digital Capacitive Touch Sensor! This is the same sort of technology found in modern smartphones, and is a great addition to any ~duino project! This little sensor can "feel" touch and feedback a digital high/low voltage level. It can even detect a touch with a thin layer of paper or cloth between you and the sensor! Features: Allows voltage supply of 3.3V or 5V Standard assembling structure (two 3mm holes with multiple of 5cm as...

Line tracking is the most basic function of a smart mobile robot. It is one of the easiest ways for a robot to successfully and accurately navigate. The Digital Line Tracking Sensor will guide your robot by telling white from black quickly and accurately, via TTL signal. With a drawn path and good programming, you can ensure results that are far more consistent than if the robot was simply told where to go without any reference. You can combine several line following sensors with other ranged...

The Digital Piezo Disk Vibration Sensor gives your project clear analog input from vibration! The board buffers a piezoelectric transducer that responds to changes in vibration by generating a measurable output voltage change which is proportional to the strength of the movement.

This module is a Digital Self-Locking Switch. Press the button to turn it to the "on" state and press it again to turn it to the "off" state. The board has immersion gold plating and is compatible with the 3-pin interface making it easy to connect to a RobotGeek Sensor Shield

The Grove - Hall Sensor measures the Hall Effect, which is a production of a voltage difference across an electrical conductor, transverse to an electric current in the conductor, as well as a magnetic field perpendicular to the current. The output of the continuous-time switch Hall sensor on this Twig switches low and turns on when a magnetic field (south polarity) perpendicular to the Hall sensor exceeds the BOP threshold, and it switches high (turns on) when the magnetic field disappears. ...

Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. The Grove - High Temperature Sensor uses a K type thermocouple for temperature detection, with a Thermistor to detect the ambient temperature, used as a cold-compensation reference. The detectable range of this Sensor is -50℃ to 600℃ (-58ºF to 1112ºF), and the accuracy is rated at ±(2.0% + 2℃). Package Includes: Grove - High Temperature Sensor x1 Thermocouple Temperature Sensor x1 24AWG Grove Cable...

HN11-I101 is the standard idler bearing set for Dynamixel XL 430 series.This idler bearing is connected to the opposite side of the output shaft of Dynamixel X, and canbe used to assemble the hinge frame on it.Patented hollow structure enables this set to be assembled with Dynamixels without screws.■ Basic ComponentsItemsQuantityBearing SetIdler (HN11-I101)1Idler Cap (DC11)1ScrewBolt (PHS M3*5)1* Hinge frame not included■ Assembly ■ Part FeaturesIdler : The idler is firmly assembled with...

The IMAX B6 is an advanced multi-function charger, able to charge, balance and discharge Lion, LiPo, LiFe (A123), NiCd and NiMH batteries. It can also be used to charge Lead Acid (Pb) batteries. It has a wide variety of voltage settings for charging various cell count batteries, as well as a 0.1 amp adjustable charge rate of up to 5 amps. To use this charger with our line of Thunder Power LiPos, you will need an E-Flite Balance Charger Adapter Cable Pack. This charger requires an 11-18v input...

This is a standalone DC Voltmeter. It measures 3V-30V with ±1% accuracy. Best suited for battery level display. Just apply two wires on the power without any extra circuitry or components, it gives the reading straight away. Easy to use, and is a good companion to robotic applications.

This little IR remote control would be handy for controlling a robot or other project from across the room. It has 21 buttons and a layout we thought was handy: directional buttons and number entry buttons. The remote uses the NEC encoding type and sends data codes 0 thru 26 (it skips #3, #7, #11, #15, #19 and #23) to address #0. You can use this to control something that is expecting NEC codes or you can pair this with virtually any IR remote receiver sensor. Battery included!

180cm USB 2.0 Cable.The cable includes a common mode choke/filter for noise reduction.The USB Mini-B connector plugs into the device. The USB type A connector goes into the computer.

The NeoPixel Ring - 8 x WS2812 5050 RGB LED is a small ring of clever WS2812 LEDs that gives you control over which LEDS are active, individual color, and brightness. Using the RobotGeek Sensor Shield, you can quickly and easily hook up the NeoPixel Ring using a 3-pin sensor cable and start making something flashy! The WS2812s are each addressable as the driver chip is located inside the LED. Each NeoPixel Stick has ~18mA constant current drive so the color will be very consistent even if the...

The PC USB Interface for Mighty Zap Linear Actuators is an interface board to control parameters with a PC. Easily test, control, and manage your Mighty Zap Linear Actuators with the Servo Manager Software! Features: Operation parameter setting Storage memory setting Error indication setting System reset Firmware update Works with: Mighty Zap 30mm Stroke 7.4V 6N TTL / PWM Mini Linear Actuator Servo Mighty Zap 30mm Stroke 7.4V 12N TTL / PWM Mini Linear Actuator Servo Mighty Zap 30mm Stroke 12V...

The PhantomX Metal Hexapod MK-III Upgrade Kit is designed for use with the Robotis DYNAMIXEL AX (Both AX-12A and AX-18A actuators are compatible) line of robot servos and functions as both an upgrade of the previous version of the PhantomX Hexapod (MK-II) or as a stand alone platform to build your own DYNAMIXEL AX servo based Crawler. This kit contains all of the frame pieces and hardware required for the build, you will need to supply servos, cables and electronics. If you would like a kit...

The PhidgetSBC3 is a Single Board Computer with an integrated PhidgetInterfaceKit 8/8/8. At its most basic, it can be thought of as a Phidget that you connect using a network cable instead of USB. The PhidgetSBC3 also provides six high-speed ports that allow you to use normal USB Phidgets over its network connection. This can extend the effective range of a Phidget from USB’s maximum of 15 feet, to anywhere that your network reaches.The PhidgetSBC3 exposes an easy to use interface for setting...

Ground - BlackIndex (Optional) - GreenA Channel - White+5V DC - RedB Channel - BrownConnector used is a Molex 50-57-9405. The index channel is used by some encoders to keep track of the number of full rotations the encoder has made. Encoder boards that don't support indexing can still use this cable to read the encoder.

The 3852 Enclosure is designed to protect the 1018 - PhidgetInterfaceKit 8/8/8 while still giving you access to the ports and terminal blocks through openings in the enclosure.There are mounting holes that go through the bottom of the enclosure, so the board can be mounted to a flat surface and the cover can snap on top.Note: Phidget Interface Kit and mounting screws not included. ...

Ever want your robot to hunt down heat objects or navigated with fire? With the Positioning IR Camera, you can track up to four heat/IR sources simultaneously! The applications are plenty and can go from tracking of robots with IR transmitters for navigation to light barriers, determining the direction an object is going, working as a flame sensor, or tracking heat sources. It's fully compatible with Arduino with only four wires over I2C. This infrared positioning camera can be controlled with...

Customers can NOT use the BT-410 to connect to the PC.Please use the BT-210 to connect your robot with a PC. ROBOTIS BT-410 is a bluetooth wireless communication solution for IoT.With the latest near field communication technology, it has low power consumption and is optimized for mobile applications.Package Contents:Contains 1 BT-410 bluetooth slave moduleFeatures:- Enables serial communication (UART) via Bluetooth communication.- Case that protects the circuits and a connector-type cable...

Hinge frame set for DYNAMIXEL X-series 430 models. Hinge frame and Idler Bearing set are included. Cannot be assembled with DYNAMIXEL MX series.

Frame for DYNAMIXEL X-series 430 models. Can be used by assembling on the side of the actuator. Cannot be assembled with DYNAMIXEL MX series.

Frame for DYNAMIXEL X-series 430 models. Can be used by assembling on the side of the actuator. Cannot be assembled with DYNAMIXEL MX series.

HN12-I101 is the standard idler bearing set for Dynamixel X-series 430 models. This idler bearing is connected to the opposite side of the output shaft of Dynamixel X, and can be used to assemble the hinge frame on it. Patented hollow structure enables this set to be assembled with Dynamixels without screws. (Enclosed screws are used to assemble the frame to the idler.) This idler bearing set cannot be assembled with Dynamixel MX series.

HN12-N101 is the standard horn set for Dynamixel X-series 430 models. This horn set can be assembled on the output shaft wheel gear of Dynamixel X in order to assemble with frames such as a hinge or an adapter. This horn set cannot be assembled with Dynamixel MX series and previous frames.

This is the RS-485 communication 4P cable set for Dynamixel X-series. Flexible sheath resists against breaking and peeling of the cable. High pull out force of the connector maintains stable connection. The cable holder will help user to achieve neat cable wiring. Compatible with Dynamixel XM430.

This is the RS-485 communication 4P cable set for Dynamixel X-series. Flexible sheath resists against breaking and peeling of the cable. High pull out force of the connector maintains stable connection. The cable holder will help user to achieve neat cable wiring. Compatible with Dynamixel XM430.

This is the RS-485 communication 4P cable set for Dynamixel X-series. New style JST connector is applied on one side of the cable while old style Molex connector is applied on the other side. This cable is used when connecting Dynamixel X-series to other controllers with Molex connectors or USB2Dynamixel. Compatible with Dynamixel XM430 and OpenCM485 expansion board or connecting with USB2 Dynamixel.

This is the RS-485 communication 4P cable set for Dynamixel X-series. Flexible sheath resists against breaking and peeling of the cable. High pull out force of the connector maintains stable connection. The cable holder will help user to achieve neat cable wiring. Compatible with Dynamixel XM430.

RoMeo V2 is an All-in-One Arduino compatible microcontroller especially designed for robotics applications, and extended devices. Romeo benefits from the Arduino open source platform, it is supported by thousands of open source projects, and can easily be expanded with Arduino Shields. The integrated 2 way DC motor driver and Xbee socket allows you to start your project immediately without the need for an additional motor driver or wireless shield! Romeo V2 also supports stepper motor control....

This Self Centering Joystick W/5k Pots would be a sturdy addition to any control pad. Like most joysticks, this one uses 2 potentiometers to measure the current angles of the joystick, but this one also has fine adjustment levers for both potentiometers. Each potentiometer comes pre-wired without headers. 2.20" x 2.20" x 1.17"

This Single Wheel and Hub Set is the same one used in our Robot DC Gearhead Motor & Wheel Starter Kit . This Wheel and Hub set can be used with 6mm diameter shafts. Our hubs are designed for a 25mm long shaft, though they can accomadate longer shafts. 3mm tapped holes are available to tighten the hub to the shaft as well as attach the wheels to the hub. The wheel is 90mm in diameter (including the rubber tire). Each Kit Includes Aluminum Hub Wheel Plates & Hardware (makes one 90mm diameter...

This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount of power and can operate from a single +3.3VDC supply. This breakout board includes the SP3485 RS-485 transceiver, filter capacitor, and other components shown on the schematic. The RS-485 output has been...

Is the Arduino Uno's hardware just not cutting it? Do you need a more powerful platform, but you're not ready to move away from the Arduino IDE? Then the Teensy is the perfect ARM based micorcontroller for your next robot project. The Teensy 3.1 is a complete USB-based microcontroller development system and is as versitile as it is powerful. A custom Teensy installer and bridge application will easily allow you to write sketches for the Teensy and load them on to the Teensy. All programming is...

Whether you've got a crawler, biped or rover, you're going to need a battery pack to get your robot moving on its own. Lithium Polymer batteries are a great choice for robot batteries because they have great capacity-to-weight ratios, giving you lots of power for very little weight. Our Lion 7.4V 4500 MAH 30C Battery is a great medium sized battery that can discharge up to 55A continously! To make it easy to connect/disconnect the battery from your project, each of these batteries has a Female...

USB 3.0 A to Micro B cable.

The USB Charger Doctor is a handy tool that measures the working voltage and current output for any USB port and project. Plug the Doctor between a USB port and your USB device, and it will check the current draw with a 0.05 ohm resistor in line with the power pin. Data lines pass through as normal. You can use this device from 3.5-7VDC input voltage (although most USB devices tend to hover around 4.75 to 5.25) and up to 3A of current. It flips between voltage and current readouts roughly...

The USB2AX AX/MX Servo Manager Kit allows you to connect with your AX/MX Dynamixel servos utilizing a half-duplex TTL interface 3-pin connector! The USB2AX works as a serial device, receiving messages from your PC via USB, and transmitting the data over to the DYNAMIXEL chain. You can send and read data to/from DYNAMIXEL servos just like you would with a microcontroller. This kit is very similar to the Dynamixel Servo Manager Kit, however, it does not have a 4-pin connector for communication...

This 12V Vacuum Pump is a great solution for a small project that requires a lot of suction power. This is the same pump used in Sparkfun's universal jamming gripper project! To use this pump for an arduino project, all you need is a Robot Geek Relay and a separate 12V power supply. Our 3.5mm silicone tubing fits this pump. ...

TheXSP - Arduino Programmer (XBee, FTDI, ISP) is designed for Arduino/AVR devices. It is a driver free programmer, supporting Arduino/AVR ISP and FTDI programming. It can provide both 5V and 3.3V power output or self-adaption power output (OFF mode). Supports Xbee socket and auto-matches ISP clock frequency. Convenient and easy to use! Features: Multi-function Supports Arduino/AVR ISP programming Supports Arduino FTDI programming Supports serial port communication Flexible Power Management...

The Arduino Due represents the next generation of Arduino hardware. This board is based on the Atmel SAM3X8E ARM Cortex-M3 CPU, a 32-bit, 84 MHz microcontroller. This board will give you 96 Kbytes of SRAM, as well as 512 Kbytes of flash memory to hold store your code. The Due even has a DMA controller to help relieve the processor of memory intensive tasks. The Arduino Due has some amazing capabilities. It has 54 Digital I/O pins, 12 of which can be used for PWM. The Due can use any of these...

The Arduino Uno is a great place to start in the Arduino World, but sometimes you need a few extra features to get your project up and running. The Arduino Leonardo , a variant of the Uno, is just the board you need! So what's so special about the Leonardo? The Leonardo can easily act as USB HID(Human Interface Device) such as a Keyboard or Mouse, opening a whole class of projects for you to explore with yout Arduino. This is accomlished by using the ATmega32u4, a microcontroller that acts...

Overview The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter...

Overview The Arduino ADK is a microcontroller board based on the ATmega2560 (datasheet). It has a USB host interface to connect with Android based phones, based on the MAX3421e IC. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. The ADK is based on the Mega 2560. Similar to the Mega 2560 and Uno, it features an...

 It's blue! It's skinny! It's the Arduino Pro! SparkFun's minimal design approach to Arduino. This is a 5V Arduino running the 16MHz bootloader (select 'Arduino Duemilanove w/ 328' within the Arduino software). The power switch was moved to the side of the board (good idea Limor!) to allow control when a shield is attached. Please note: The right-angle power switch is fragile. We're working on making the switch stronger. For now, please be gentle. Arduino Pro does not come with connectors...

It's blue! It's thin (0.8mm)! It's the Arduino Pro Mini! SparkFun's minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader (select 'Arduino Duemilanove w/ 328' within the Arduino software). Arduino Pro Mini does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We recommend first time Arduino users start with the Duemilanove. It's a great board that will get you up and running quickly. The Arduino...

The 6DOF Atomic is a stripped-down IMU, designed to give good performance at a low price. The unit can run as a hard-wired UART interface (0-3.3V, 115200bps), or optionally with an XBee  RF module, and is powered from a single LiPo (Lithium Polymer) battery. The processor is an Atmel ATMega168 running at 10MHz with 6 dedicated 10-bit ADC channels reading the sensors. Source code for the 6DOF Atomic is freely available and compiles with the free AVR GCC compiler. The 6-DOF Atomic uses...

Dynamixel Comparison Guide This is a 6 piece Bulk package of the AX-12A. In this bulk pack, the servos are bare and do not come with any additional cables, brackets, or hardware. If you need this hardware, it must be purchased separarely.The AX-12A servo actuator from Robotis is the most advanced actuator on the market in this price range and has become the defacto standard for the next generation of hobby robotics. The AX-12A robot servo has the ability to track its speed, temperature, shaft...

Software, meet hardware. Netduino is an open source electronics platform using the .NET Micro Framework. Featuring a 32-bit microcontroller and a rich development environment. Suitable for engineers and hobbyists alike. Code. Debug. Repeat. .NET Micro Framework combines the ease of high-level coding and the features of microcontrollers. Enjoy event-based programming, multi-threading, line-by-line debugging, breakpoints and more. Design files included. Netduino is an open source electronics...

The caster wheel kit is the utmost in quality and performance. It features precision machined 6061 aluminum parts combined with high quality ball bearings and durable 3-inch Du-Bro pneumatic rubber tires. The dual independent tire design reduces vibration and drag, while also increasing its load-carrying capacity. You will be amazed at how smoothly and silently these caster wheels roll. Cheaper alternatives often use stamped sheet metal bearing tracks which tend to be sloppy and can easily...

The PhidgetLED 64 allows you to independently control 64 Light Emitting Diodes. Each LED can be turned on and off, and its brightness controlled. Most standard LEDs with colors such as red, amber, orange, yellow, and green have forward voltages below 3.0 Volts, and can be used with the PhidgetLED by simply soldering them to a connector-wire and inserting the wire into any PhidgetLED board connector. Output Update Rate: 30 updates/second Output Anode Voltage: 3.3VDC Output Current (max): 30mA...

Everything you need to be up and running with a Geekduino and Sensor shield I/O break out board to mount to your projects. GeekduinoSensor Shield10 Robotgeek sensor cablesDuino Mounting PlateThe Robotgeek Sensor Shield breaks out the digital and analog pins into easy to use 3-pin connectors. Each connector supplies 5 volts, ground, and a signal pin. These connectors can easily be connected to RobotGeek Sensors as well as a wide variety of sensors, actuators and output...

Seeeduino v3.0 328P is an Arduino-compatible board. Its design is based on Duemilanove scheme, 100% compatible to existing programs, shields and IDEs. On the hardware however, many changes have been made to improve the flexibility and user experience. Arduino is an open-source electronics prototyping platform based on flexible, easy-to-use hardware and software. It's intended for artists, designers, hobbyists, and anyone interested in creating interactive objects or environments. ...

Description: Riding on the waves of the very popular Arduino USB board is this small prototyping shield. Originally spawned with collaboration between the folks at SFE and ITP @ NYU, the Protoshield mates with the Arduino USB board and gives the user a small soldering area, two general LEDs, access to a BlueSMiRF socket, a general pushbutton switch, and most important of all - the Arduino reset switch is brought to the top level. This comes in kit form and must be soldered together by the end...

You are in the middle of working on your latest robot, when you need to program a new board you just got in. You dig through your bin of USB cables only to find that you have hundreds that have the wrong end, and exactly zero that have the end you're looking for. As luck would have it, you remember that you ordered the Sparkfun Cerberus USB Cable! With this cable, you will always have the right connection. The Cerberus USB Cable has the standard A-type connector, which you can plug into your...

The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100ethernet chip (datasheet). The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps...

Connecting the Arduino to the internet isn't cool. You know what's cool? Connecting the Arduino to the internet wirelessly! --> Do you have a great arduino project that needs a wireless interent connection? Then check out the Arduino Wireless Shield!This shield will turn your Arduino into a wireless powerhouse, enabling you to connect to online servers, or even act as a server! This is also a great tool to attach your arduino to Wi-Fi enabled devices. The Wifi Shield uses an AVR32 processor,...

This is a motor shield for Arduino that will control two DC motors. Based on the L298 H-bridge, the Ardumoto can drive up to 2 amps per channel. The board takes its power from the same Vin line as the Arduino board,  includes blue and yellow LEDs to indicate active direction, and all driver lines are diode protected from back EMF. Control for motor attached to OUT1/2 is connected to digital line 12 (direction A) and digital line 10 (PWM A). Control for motor attached to OUT3/4 is...

The Bluetooth Shield integrates a Serial Bluetooth module. It can be easily used with Arduino/Seeedstudio for transparent wireless serial communication. You can choose two pins from Arduino D0 to D7 as Software Serial Ports to communicate with Bluetooth Shield (D0 and D1 is Hardware Serial Port). The shield also has two Grove connectors (one is Digital, the other is Analog) for you to install Grove modules. Features Seeeduino/Arduino compatible Up to10m communication distance in house without...

The Danger Shield is an add-on for the Arduino & Freeduino micro controller boards. It contains a variety of fun and useful electronic circuits that you can use to do fun and useful things. It is a fully self-contained shield. You plug it into your Arduino, and you can immediately start using it. No extra things to hook up, no external components. Just a really rad board ready to rock.  Note: This is a kit- Assembly & Soldering is required. Some of the features of the board are: 3...

The EL Shield kit is an easy to use shield to control electroluminescent (EL) devices (such as EL wire) with either an Arduino or Seeeduino. The board has 4 outputs so you can control up to 4 devices separately! It can drive EL wires at long as 15 m (49 ft). This shield come without the headers soldered on, so you'll have to attach them before use. If you know how to control an LED, you can control EL devices. The EL Shield makes it that easy! The shield uses pulse-width modulation (PWM), so...

Description The GPRS (General Packet Radio Service) Shield is a new nonvoice value added service that delivers GSM/GPRS 850/900/1800/1900MHz performance for voice, SMS, Data, and Fax in a small form factor and with low power consumption. It is controlled via AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands), and fully compatible with Seeeduino/Arduino and Mega. The GPRS Shield has 12 GPIOs 2 PWMs and 1 ADC(They are all 2V8 logic). Features Quad-Band 850/ 900/ 1800/ 1900 MHz GPRS...

Quickly add motor control to your Arduino or Seeeduino with the Grove Motor Shield! You can use the shield to easily connect 2 brushed DC motors, which makes it great for controlling wheeled platforms like the Budget Bot Chassis. Use the Grove Motor Shield to control motors from 6-15 volts, with up to 2 amps per channel. Easily accessible screw terminals will let you connect your motors and external power. This shield is also great if you're using the Grove sensors, since it has 13 Grove ports...

Every project is better with music! Build your own music player with the music shield. Or use it to give your robot a voice and/or sound effects. The Music Shield is an ipod/iphone dock compatible shield. It can work with Arduino, Seeeduino, Seeeduino Mega and Arduino Mega2560. It is based on the VS1053b and can play variety of music format stored on MicroSD card with Seeed Studio provided Arduino Library. Note: Recording is only supported by Seeeduino Mega and Arduino Mega2560. Documentation...

Note: The 1047_1B is identical to the 1047_1 but no longer comes with associated cables. Cables sold separately: 3018 Mini USB Cable 180CM & 3019 HighSpeed Encoder Cable 50cmThe PhidgetEncoder Highspeed 4-Input can be used with a wide assortment of mechanical and optical encoders. The encoder should be of quadrature output type, indicating that there will be two quadrature output channels (usually labeled A and B) and an optional third output channel to signal when the index pin (a reference...

Product Features Connects to any typical two-bit optical encoder. Returns up to 500,000 counts per second. Can be used as an accurate human input device. Connects directly to a computer’s USB port. Product Description The PhidgetEncoder HighSpeed connects to any typical two-bit optical encoder and can return up to 500,000 counts per second. Specifically it reads a standard incremental non-differential TTL encoder. The 1057 can be used to measure shaft speed or as a very accurate human input...

Seeed's Wifi Shield utilizes a RN171 wifi module to provide your Arduino with serial ethernet function. It only takes two pins to hook your device up to 802.11 b/g wireless networks! It features an independent antenna which can cover a wider range and transmit stronger signals. The wifi shield supports common TCP, UDP and FTP communication protocols creating a perfect solution to most wireless network projects such as smart home networks, robotic control, personal weather stations,...

The newest version of the Xbee Shield is a standardized and stackable shield for Arduino. You can easily stack any modules from the Bee series and build a wireless network for your project! In spite of that, it is also equipped with the function of level conversion which enables a double-way conversion between high and low IO levels. The reversed digital pins facilitate users to select TX-RX ports using jumper caps.***Seeed Studio's XBee Shield V2.0 comes unassembled and will require soldering...

Dynamixel Comparison Guide This is a 6 piece Bulk package of the AX-18A. In this bulk pack, the servos are bare and do not come with any additional cables, brackets, or hardware. If you need this hardware, it must be purchased separately. The AX-18A servo actuator from Robotis is the next step up from the hugly popular AX-12A Servo, offering nearly twice the speed and 15% more torque! The AX-18A robot servo retains the formfactor and all of the same features of its predecessor: the ability to...

Additional cables for the Phidgets LED64. 4-Conductor, connectors on both ends, length is 60cm. This product is part of the Phidgets family! Phidgets are an easy to use set of USB-based building blocks for low cost sensing and control from your PC. A wide array of sensors, I/O devices, and controllers are available. To view the entire Phidgets product line, follow this link. Getting Started with Phidgets Phidgets Documentation: Manuals, data sheets, and tutorials for Phidgets products....

Product Description The DE-SW0XX family of switch mode voltage regulators are designed to be the easiest possible way to add the benefits of switch-mode power to a new or existing project. The DE-SW0XX family is pin-compatible with the common 78XX family of linear voltage regulators. They have integrated decoupling capacitors, so external capacitors are not generally necessary. Standard available voltages are 3.3 and 5 volts. Need a different voltage? Try DE-SWADJ3. What is a switching...

1-Pound FlexiForce Force Sensor Measures from 0 to 1 lbs. FlexiForce Sensor Model A201.   FlexiForce is... A versatile, durable piezoresistive force sensor that can be made in a variety of shapes and sizes A piezoresistive sensing device in which resistance is inversely proportional to applied force A customizable, economical force measurement tool that is easily integrated into OEM products A patented, ultra-thin (0.008"), flexible printed circuit that senses contact force A force...

Description: The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse. EasyDriver requires a 7V to 30V supply to power the motor, and has an on board voltage regulator for the digital interface. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors. This is the newest version of EasyDriver V4...

Product Specifications Sensor Output Type: Non-Ratiometric Response Time Max:2ms Peak Sensitivity Wavelength:625 nm Light Level Min:1 lux Light Level Max(5v): 1000 lux Light Current Ratio:1.2 Device Current Consumption: 5 mA Output Impedance: 1K ohms Bandwidth / Reaction Time: 50 Hz Minimum / Maximum Voltage: 2.4VDC to 5.5VDC Operating Temp Min:-40° Operating Temp Max:85° This product is part of the Phidgets family! Phidgets are an easy to use set of USB-based building blocks for low...

Power up your rover, or take your robot arm off the grid with the 7.4V 2200mAh Lithium Ion Battery! This battery has excellent capacity for robotics projects utilizing several RobotGeek Servos. To make it easy to connect/disconnect the battery from your project, each of these batteries has a Female T-Connector (Deans Ultra Plug compatble), and for easy charging, a barrel Jack for use with the Charger with over-voltage protection (included). If discharged too low, Lithium Ion batteries can...

The graph above shows the detection pattern for a 4-foot tall, 3.25-inch diameter post.  Grid squares equal 1 foot. For more information on the LV-MaxSonar®-EZ0™ please... download the datasheet:LV-MaxSonar-EZ0-Datasheet.pdf The LV-MaxSonar-EZ0 offers very short to long-range detection and ranging, in an incredibly small package with ultra low power consumption. The MaxSonar-EZ0 detects objects from 0-inches to 254-inches (6.45-meters) and provides sonar range information from 6-inches...

Features: Powerful 12 VDC motors provide plenty of torque Precision machined 6061 aluminum hardware Conveniently positioned screw holes make mounting this kit a breeze. Rugged pneumatic tires are well-suited for a variety of terrains 5V supply required for Position Controllers 36 encoder positions per revolution; approx 0.5 inch resolution with 6" diameter wheel Compatible with any microcontroller Single I/O line can control up to 4 Position Controllers Strong but light - only 3.2 lbs (1.45...

This is a 12-foot, 3-pin cable for connecting sensors to the analog inputs on the Phidgets 8/8/8 Interface Kit. This product is part of the Phidgets family! Phidgets are an easy to use set of USB-based building blocks for low cost sensing and control from your PC. A wide array of sensors, I/O devices, and controllers are available. To view the entire Phidgets product line, follow this link. Getting Started with Phidgets Phidgets Documentation: Manuals, data sheets, and tutorials for Phidgets...

The PhidgetInterfaceKit 0/16/16 provides: 16 Digital Inputs sensing up to 30VDC 16 Digital Outputs controlling up to 30VDC LED indicators on all I/O channels The Digital Outputs can be used to directly control substantial devices, switching up to 30VDC at up to 2 Amps. The Output acts as a switch to ground, and is protected from transient voltages typical when switching inductive devices - relays, solenoids, motors. The Outputs can be used to directly control devices requiring substantial...

The PhidgetServo 1-Motor is a USB based controller that can control a Remote Control (RC) servo motor. The motor output is powered directly from the USB port. The PhidgetServo has a step accuracy of 0.1 degrees, but the actual positional accuracy of the servo motor is dependant on the physical characteristics of the specific servo used. If you need a servo with this controller, buy the kit instead and save some money. Comes packaged with a 6-foot USB Cable, and a Getting Started Manual. For...

Overview This ball caster kit includes a black ABS housing, a 3/8" diameter plastic ball, two spacers (1/16" and 1/8" thick), and two #2 screw sets. The total height of this ball caster is 0.4" with no spacers. You can also adjust the height by adding the spacers. The ball caster can be mounted to a chassis by the two screw sets included in the kit. The distance between the two screw holes is 0.53". ...

The little brother to the 4.5" Flex Sensor, the 2.2" Flex Sensor is just as fun! This sensor's diminutive size makes it great for all sorts of small spaces. The flex sensor changes its resistance as its flexed, so you can easily create an analog signal to connect to your microcontroller. We recommend using our Voltage Divider to easily create that signal. The connector is .1"/2.5mm spaced, so it will work with standard breadboards. We recommend that you reinforce the base of the sensor when...

Description: A simple flex sensor 4.5" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the original Nintendo Power Glove. I love the Nintendo Power Glove. It's so bad! The resistance of the flex sensor changes when the metal pads are on the outside of the bend (text on inside of bend). Straight (unflexed) resistance: ~9000 Ohm 90 degree bend resistance: ~14000 Ohm 180 degree bend...

This page is for the RFIDuino V1.2. Visit this guide to see the differences between the Version 1.1 and 1.2 Hardware. The RFIDuino is an Arduino RFID Shield which makes Arduino RFID projects super easy to build. Just drop the RFIDuino Shield onto your Arduino microcontroller, load our sample code, and you'll be reading tags in no time! Our getting started guide will take you through the process of working with the RFIDuino from loading basic code to more advanced projects like triggering...

Get your rover rolling with our new custom Robot DC Gearhead Motor & Wheel Starter Kit. Each kit comes with 2 motors and wheel sets as well as a pair of brackets to mount your motors to your robot. Each wheel is 90mm in diameter (including the rubber tire). The motors in this kit use Hall Effect Quadrature sensors to achieve an encoder output of 520 ticks/revolution, allowing you to control the motors very precisely. Each motor includes a 6-pin cable that breaks out motor inputs and the...

Get ready to bring your robotic dreams to life with the RobotGeek 180 Degree Robot Servo! This metal-geared servo is perfect for building robotic joints and will help you create your own custom robotic arms, crawlers, and more! And because these servos use a standard PWM signal for control, they're easy to directly interface with microcontrollers like the Arduino! RobotGeek Servo by RobotGeek on Sketchfab Idler Horn The difference between a regular servo and robot servo is the Idle Horn. This...

The Geekduino is the new Arduino Compatible board from RobotGeek! This board goes into every RobotGeek Robot Kit and is the perfect microcontroller for your next robotic project! The Geekduino uses the ubiquitous Micro USB port to power and program the board. The Geekduino can also be powered via the ultra low-profile flat DC power jack. A series of switches allows you to toggle on/off the Geekduino's FTDI reset (handy for software projects) as well as change the operating voltage of the...

The Robot Geek Sensor Cable Pack will hook you up with all your sensor and servo wiring needs and beyond. This variety cable pack includes: 3x 3 Pin Female to Female Y Cable 1x 32 Foot Standard Servo Wire 20x 3 Pin Sensor Cable 10x 2 Pin Dual-Female Jumper Wires (300mm) 10x Sensor Squids 25x 2-Pin Couplers 25x 3-Pin Couplers ...

Product Description Sabertooth 2X5 is the motor driver of choice for small differential-drive robots. It is ideal for smaller robots- up to 3lbs in combat or 25 lbs for general purpose use. It is also a great choice in any application where you need to control two brushed motors. Out of the box, the Sabertooth can supply two DC brushed motors with up to 5A each continuously. Peak currents of 10A are achievable for short periods. Because Sabertooth 2x5 incorporates soft current limiting and...

This is a standard male-to-female serial cable. Great for connecting any serial device with a DB-9 connector to a PC.

The Floor Mat Switch works by spacing two strips of metal apart with thin squares of foam in-between them every .75 inches. The pairs of metal strips are spaced out 2.5 inches from each other for the length of the mat. When someone steps on the mat their weight presses the two metal strips together creating a closed contact. All the strips are connected down both sides of the mat creating one large switch. The individual strips can be cut apart to create individual switches and the mat itself...

This Interbotix Lab Custom Frame is great for building robots from the -64 and -106 series DYNAMIXEL robot servos. For -106 servos, the frame will fit perfectly onto the servo. Each frame comes with two small spacer and longer bolts for a perfect fit on any -64 series servo - just fit one spacer in between the frame and the horn, and one spacer between the frame and the idler bearing. This Kit does NOT come with X-101 Cross Frames or F-101 Flange Frames. Contents 1 x Black 45 Degree Bracket 1...

This Interbotix Lab Custom Frame is great for building robots from the -64 and -106 series DYNAMIXEL robot servos. For -106 servos, the frame will fit perfectly onto the servo. Each frame comes with two small spacer and longer bolts for a perfect fit on any -64 series servo - just fit one spacer in between the frame and the horn, and one spacer between the frame and the idler bearing. Contents 1 x Black X-Long Bracket 1 HN-05 I101 Idler Kit 2 x plastic spacer for -64 series servos 10 x M2.5*6...

This Interbotix Lab Custom Frame is great for building robots from the -64 and -106 series DYNAMIXEL robot servos. This wide hinge frame has been designed for double-axis robot joints, mounted in a side to back configuration. For -106 servos, the frame will fit perfectly onto the servo. Each frame comes with two small spacer and longer bolts for a perfect fit on any -64 series servo - just fit one spacer in between the frame and the horn, and one spacer between the frame and the idler bearing....

The Interbotix MX-64 / 106 Foot (Pair) are an aluminum feet, perfect for your next MX 106 or 64 robot.. This is the same frame as used in the HR-OS5. Compatible DYNAMIXEL Servos MX-64T MX-64R MX-106T MX-106R This product contains 2 plates. Each plate is usually used in conjunction with a Dual Axis Robot Joint. The dual joint can be made out of MX-64s or MX-106s. ...

This Interbotix Lab Custom Frame is great for building robots from the -64 and -106 series DYNAMIXEL robot servos. The Interbotix MX-64 / 106 Tibia is the same frame as used in the legs of the HR-OS5. For -106 servos, the frame will fit perfectly onto the servo. Each frame comes with two small spacer and longer bolts for a perfect fit on any -64 series servo - just fit one spacer in between the frame and the horn, and one spacer between the frame and the idler bearing. Tapped holes on the...

Large sized AC powered linear servo motors have been used widely in various industrial applications. However compact linear servo motors with DC power have had limited applications due to limited force, speed, accuracy and durability - despite high market demand. Say goodbye to limitations with the Mighty Zap 30mm Stroke 12V 12N TTL / PWM Mini Linear Actuator Servo! The Mighty Zap Series from IR Robot outperforms other linear actuators by virtually every metric, making them a fantastic choice...

Large sized AC powered linear servo motors have been used widely in various industrial applications. However compact linear servo motors with DC power have had limited applications due to limited force, speed, accuracy and durability - despite high market demand. Say goodbye to limitations with the Mighty Zap 30mm Stroke 12V 6N TTL / PWM Mini Linear Actuator Servo! The Mighty Zap Series from IR Robot outperforms other linear actuators by virtually every metric, making them a fantastic choice...

Large sized AC powered linear servo motors have been used widely in various industrial applications. However compact linear servo motors with DC power have had limited applications due to limited force, speed, accuracy and durability - despite high market demand. Say goodbye to limitations with the Mighty Zap 30mm Stroke 7.4V 12N TTL / PWM Mini Linear Actuator Servo! The Mighty Zap Series from IR Robot outperforms other linear actuators by virtually every metric, making them a fantastic choice...

Large sized AC powered linear servo motors have been used widely in various industrial applications. However compact linear servo motors with DC power have had limited applications due to limited force, speed, accuracy and durability - despite high market demand. Say goodbye to limitations with the Mighty Zap 30mm Stroke 7.4V 6N TTL / PWM Mini Linear Actuator Servo! The Mighty Zap Series from IR Robot outperforms other linear actuators by virtually every metric, making them a fantastic choice...

The BIOLOID Compatible Metal F1 Bracket is an aluminum replacement for the standard BIOLOID F1 bracket. 4 tapped holes on the sides of the frame make it easy to mount cable holders and 3D frames. This is the same frame as used in the HR-OS1 Compatible DYNAMIXEL Servos AX-12A AX-18A This product is just the single metal bracket. This frame requires a Hub & Washer, an M3 * 10 bolt, and 4 M2*6 bolts (both bolts can be found in the Nut and Bolt Variety Pack). The AX-12A comes with this hardware,...

The BIOLOID Compatible Metal F2 Bracket is an aluminum replacement for the standard BIOLOID F2 bracket. 4 tapped holes on the sides of the frame make it easy to mount cable holders and 3D frames. Compatible DYNAMIXEL Servos AX-12A AX-18A AX-12W MX-12W This product is just the single metal bracket. This frame requires a Hub & Washer, an M3 * 10 bolt, and 4 M2*6 bolts (both bolts can be found in the Nut and Bolt Variety Pack). The AX-12A comes with this hardware, but the AX-18 does not. ...

The BIOLOID Compatible Metal F3 Bracket is an aluminum replacement for the standard BIOLOID F3 bracket. 4 tapped holes on the top of the frame make it easy to mount cable holders and 3D frames. This is the same frame as used in the HR-OS1 Compatible DYNAMIXEL Servos AX-12A AX-18A ...

The BIOLOID Compatible Metal F4 Bracket is an aluminum replacement for the standard BIOLOID F4 bracket. 12 tapped holes on the sides of the frame make it easy to mount cable holders and 3D frames. This is the same frame as used in the HR-OS1 Compatible DYNAMIXEL Servos AX-12A AX-18A This product is just the single metal bracket. This frame requires a Hub & Washer, an M3 * 10 bolt, and 4 M2*6 bolts (both bolts can be found in the Nut and Bolt Variety Pack). The AX-12A comes with this hardware,...

The BIOLOID Compatible Metal F4 Bracket is a aluminum replacement for the standard BIOLOID F4 bracket. 4 tapped holes on the sides of the frame make it easy to mount cable holders and 3D frames. This is the same frame as used in the HR-OS1 Compatible DYNAMIXEL Servos AX-12A AX-18A Two F6 Brackets, One F7 Bracket, and Two AX-Series Servos (AX-12A, or AX-18A) are required to create a dual joint. This product is just the single metal bracket. This frame requires a Hub & Washer, an M3 * 10 bolt,...

The BIOLOID Compatible Metal F12 Brackets are an aluminum replacement for the standard BIOLOID F12 bracket Pair. These plates make great feet for your next robot. This is the same frame as used in the HR-OS1. Compatible DYNAMIXEL Servos AX-12A AX-18A This product contains 2 plates. Each plate is usually used in conjunction with a dual axis joint, consisting of 1 F5 Bracket, 2 F6 Brackets, 1 F7 Brackets and 2 AX servos. ...

These FSR's are perfect for robotic grippers, robot feet, and similar applications. We searched long and hard to find a flat force sensing resistor that we liked. When we tried these bad boys out for the first time we knew the search was over. Paper thin and well made, these FSR's are just plain fun to play with. FEATURE LIST Various sizes: .2", .5", 1.5", 24" strip Rubber backing Peel sticker backing Choice of male tabs or female connector Use voltage divider to adjust sensitivity band 0.2"...

These FSR's are perfect for robotic grippers, robot feet, and similar applications. We searched long and hard to find a flat force sensing resistor that we liked. When we tried these bad boys out for the first time we knew the search was over. Paper thin and well made, these FSR's are just plain fun to play with. FEATURE LIST Various sizes: .2", .5", 1.5", 24" strip Rubber backing Peel sticker backing Choice of male tabs or female connector Use voltage divider to adjust sensitivity band...

2.8'' TFT Touch Shield is an Arduino / Arduino Mega compatible multicolored TFT display with a 4-wire resistive touch-screen. It is available in an Arduino shield compatible pinout for attachment. The TFT driver is based on ST7781R with 8bit data and 4bit control interface.  Arduino / Mega Shield compatible footprint. TFT Resolution : 240 x 320 pixels Size : 2.8" (50.0 x 69.2 x 2.5 mm) Colors : 262K Backlight : LED Driver IC: ST7781R 4-Wire Resistive Touch Screen Application Ideas As a...

Product Description The DE-SW0XX family of switch mode voltage regulators are designed to be the easiest possible way to add the benefits of switch-mode power to a new or existing project. The DE-SW0XX family is pin-compatible with the common 78XX family of linear voltage regulators. They have integrated decoupling capacitors, so external capacitors are not generally necessary. Standard available voltages are 3.3 and 5 volts. Need a different voltage? Try DE-SWADJ3. What is a switching...

This LED Matrix is ment to be paired with the Rainbowduino LED Driver for making cool light displays. Start your own rave in your garage or make a scrolling banner for outside your room to keep pests away. Features 60mm x 60mm 64 (8x8) Super Bright RGB LEDs (Common Anode) Pairs with the Rainbowduino LED Driver Product Datasheet. Product DOCUMENTATION / WIKI Page. ...

25-Pound FlexiForce Force Sensor Measures from 0 to 25 lbs. FlexiForce Sensor Model A201.   FlexiForce is... A versatile, durable piezoresistive force sensor that can be made in a variety of shapes and sizes A piezoresistive sensing device in which resistance is inversely proportional to applied force A customizable, economical force measurement tool that is easily integrated into OEM products A patented, ultra-thin (0.008"), flexible printed circuit that senses contact force A force...

Don't be deceived, this little red board is actually a hugely powerful bluetooth modem! The BlueSMiRF Bluetooth Modem gives you a quick and easy way to add Bluetooth functionality to your project - you'll be connecting to all kinds of bluetooth devices in no time. The BlueSMiRF is the latest bluetooth wireless serial cable replacement from SparkFun Electronics! These modems work as a serial (RX/TX) pipe. Any serial stream from 2400 to 115200bps can be passed seamlessly from your computer to...

As simple as input gets, the very first computers had buttons and so will your ingenious project. The button is configured with pull-down resistor ready for use with our microcontrollers as digital input.

Infrared is a quick, cheap, and easy method to transmit data. With the Grove Infrared Transmitter you too can control legions of robotic minions - or just your TV. This emitter is designed to work in tandem with the Grove Infrared Receiver so that you can quickly build your own infrared data system. The Grove Infrared Transmitter is a great tool to cheaply integrate remote control/communication to any of your projects. Technical Specifications 10 meter detection range Grove compatible 20mm X...

Do you really know what your TV remote is saying to your TV when you hit the ‘Power’ button? Well now you can! The Grove Infrared Receiver has a 4 pin Grove-compatible breakout header, so it will connect to your Grove based project in a snap. You'll be decoding IR message in no time! You can used this receiver with an existing IR transmitter like a TV remote or you can get your hands on a Grove Infrared Emitter to build your own infrared data system. The Grove Infrared Receiver is a great tool...

Rotary potentiometers are a great way to control all sorts of devices through your Arduino - but sometimes they're a bit boring. Bring some pizazz back to your controller with the Grove - Slide Potentiometer! This Grove compatible sensor will plug directly into your Grove Sensor Shield and you'll be ready to go! You can read the data from the slider, just as you would any other potentiometer. It even has an onboard LED that you can control from your Arduino! Technical Specifications 30mm slide...

How many PlayStation 2 Controllers have to die for your next project? Now with the Grove - Thumb Joystick the answer is NONE! Like most joysticks, this one uses 2 potentiometers to measure the current angles of the joystick. However this joystick has a pushbutton hidden within! Just push directly down on the top of the joystick, and you'll feel the satisfying 'click' of a pushbutton. Use your extra input to fire the lasers, initiate uprising, or start any other robot related task. NOTE: The...

Power up your rover, or take your robot arm off the grid with the 7.4V 4400mAh Lithium Ion Battery! This battery has excellent capacity for robotics projects utilizing several RobotGeek Servos. To make it easy to connect/disconnect the battery from your project, each of these batteries has a Female T-Connector (Deans Ultra Plug compatble), and for easy charging, a barrel Jack for use with the Charger with over-voltage protection (included). If discharged too low, Lithium Ion batteries can...

The graph above shows the detection pattern for a 4-foot tall, 3.25-inch diameter post.  Grid squares equal 1 foot. For more information on the LV-MaxSonar®-EZ1™ please... download the datasheet:LV-MaxSonar-EZ1-Datasheet.pdf The LV-MaxSonar-EZ1 offers very short to long-range detection and ranging, in an incredibly small package with ultra low power consumption. The MaxSonar-EZ1 detects objects from 0-inches to 254-inches (6.45-meters) and provides sonar range information from 6-inches...

Temperature sensor with a range of -30°C to +80°C with a typical error of ±0.75°C in the 0°C to 80°C range. Note: The temperature sensor component is rated at -50°C to +150°C, but the other components on the board, the connector and the cable are rated at -30°C to +80°C. A 24" sensor cable is included. This product is part of the Phidgets family! Phidgets are an easy to use set of USB-based building blocks for low cost sensing and control from your PC. A wide array of sensors, I/O...

This is a 24-inch, 3-pin cable for connecting sensors to the analog inputs on the Phidgets 8/8/8 Interface Kit. This product is part of the Phidgets family! Phidgets are an easy to use set of USB-based building blocks for low cost sensing and control from your PC. A wide array of sensors, I/O devices, and controllers are available. To view the entire Phidgets product line, follow this link. Getting Started with Phidgets Phidgets Documentation: Manuals, data sheets, and tutorials for Phidgets...

The PhidgetAdvancedServo 8-Motor allows you to control the position, velocity, and acceleration of up to 8 RC servo motors. It requires a 6-15VDC external power supply; its switching power supply allows the 1061 to efficiently operate from 6 to 15 VDC and can be used with a wide range of batteries. The 1061 has a high resolution of 125 steps per degree; it measures the power consumption of each servo and its switching regulator protects the motors from overvoltage. It powers servo motors of up...

Control 8 DPDT mechanical relays, switching up to 250VAC/2A or 120VDC/2A.The PhidgetInterfaceKit 0/0/8 provides Small Signal Relays with 8 Relay Outputs, rated at 250VAC, or 2 Amps, for a maximum of 60 Watts. While typical mechanical relay boards are unable to switch signals due to an oxide buildup on the contacts, the 1017 excels at switching both signals and low-power applications.

The Voltage Sensor measures the differential voltage between the input terminals and outputs the difference proportionally. The maximum differential voltage that can be measured accurately is ±30V. Resources Product Manual   Product Specifications Characteristic Value Current Consumption 3.6mA Input Impedance 1MegaOhm Recommended Max Difference between Vin+ and Vin- 30V Absolute Maximum difference between Vin+ and Vin- 35V Input CMR 40V Output Range 0 to 5V Min/Max error ±2% Typical Error...

Overview This ball caster kit includes a black ABS housing, a 1/2" diameter plastic ball, two spacers (1/16" and 1/8" thick), and two #2 screw sets. The total height of this ball caster is 0.53" with no spacers. You can also adjust the height by adding the spacers. The ball caster can be mounted to a chassis by the two screw sets included in the kit. The distance between the two screw holes is 0.58". ...

RobotGeek Sensor Cables are for use with all RobotGeek sensors, shields, servos, and output devices. These cables are .1"(2.54mm) pitch and are 150mm in length with color coded wires. Add some 3-Pin Couplers to connect cables together for extension cables. These cables are also compatible with Phidgets Sensors and Electronic Brick Sensors, though they do not have the plastic buckle like traditional Phidgets/Electronic Brick Cables. ...

Get ready to bring your robotic dreams to life with the RobotGeek Continuous Rotation Servo! This metal-geared servo is perfect for building robotic rovers, spinners and more! And because these servos use a standard PWM signal for control, they're easy to directly interface with microcontrollers like the Arduino! Idler Horn The difference between a regular servo and robot servo is the Idle Horn. This horn will spin freely and is at the opposite position of the main drive horn. The idler horn...

The Arduino Platform is a great way for learning about electronics and programming, as well as creating microcontoller based projects. But even simple projects can get messy very quickly, leaving you with a pile of wires, breadboards, and components. With the RobotGeek Sensor System, you can put your project on the fast track and get it up and running in no time. The RobotGeek Sensor Shield will fit on any Standard Arduino Compatible board*, and break out the digital and analog pins into easy...

This is a Mabuchi RS-550 motor with a 3-pole balanced armature. Motor Specifications   Performance Operating v : 6v - 14.4v Nominal v : 12v No Load RPM : 18000 No Load A : 1.2A Stall Torque : 70.55 oz-in 498.2 mN-m Stall Current : 85A Kt : 0.83 oz-in/A 5.9 mN-m/A Kv : 1608 rpm/V Efficiency : 70% RPM - Peak Eff : 17250 Current - Peak Eff : 10A Physical Weight : 7.7 oz (218g) Length - for motor : 2.24 in (57mm) Diameter (with flux ring) : 1.52 in (38.5mm) Diameter (no flux ring) : 1.41 in...

A Protoshield kit for Seeeduino/Arduino MEGA. Miles of space with a huge amount of header options. Kit also comes with 5 button switches. Excellent kit for building your own MEGA shield. Features Supports both Seeeduino MEGA and Arduino MEGA All pins are brought to the top level Supports Xbee/GPS bee Rest button brought to the top level 5 button switches Tons of male and female headers Product WIKI Page. ...

One of the most favored IR range sensors on the market. Detects distances from 4" to 30" (10cm-80cm). Note: The sensor sold here is actually a Sharp IR GP2Y0A21YK0F. It has the same distance range as a GP2D12 and very similar analog output properties. The GP2D12 is extremely difficult to source currently, so these sensors provide a great alternative. For more information on the minor differences, please refer to the datasheets for each sensor: Datasheets GP2D12 Datasheet GP2Y0A21YK0F...

These are very thin variable potentiometers. By pressing down on various parts of the strip, the resistance linearly changes from 100Ohms to 10,000Ohms allowing the user to very accurately calculate the relative position on the strip. Can be used as an accurate positional indicator for CNC head positioning, variable user input (volume level input for example), straight user input (multiple button areas translate to given resistance levels), and many other applications. Unit comes with adhesive...

The Floor Mat Switch works by spacing two strips of metal apart with thin squares of foam in-between them every .75 inches. The pairs of metal strips are spaced out 2.5 inches from each other for the length of the mat. When someone steps on the mat their weight presses the two metal strips together creating a closed contact. All the strips are connected down both sides of the mat creating one large switch. The individual strips can be cut apart to create individual switches and the mat itself...

This new version adds 2 standoff holes as well as an extra decoupling capacitor. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface. The ADXL345 is well suited to measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion...

Breakout board for the 3 axis ADXL335 from Analog Devices. This is the latest in a long, proven line of analog sensors - the holy grail of accelerometers. The ADXL335 is a triple axis accelerometer with extremely low noise and power consumption - only 320uA! The sensor has a full sensing range of +/-3g. There is no on-board regulation, provided power should be between 1.8 and 3.6VDC. Board comes fully assembled and tested with external components installed. The included 0.1uF capacitors set...

Description: This is a breakout board for InvenSense's ITG-3200, a groundbreaking triple-axis, digital output gyroscope. The ITG-3200 features three 16-bit analog-to-digital converters (ADCs) for digitizing the gyro outputs, a user-selectable internal low-pass filter bandwidth, and a Fast-Mode I2C (400kHz) interface. Additional features include an embedded temperature sensor and a 2% accurate internal oscillator. The ITG-3200 can be powered at anywhere between 2.1 and 3.6V. For power supply...

This is the very popular 2.4GHz XBee module from Digi (formally Maxstream). These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported. These modules are great for working with Arduino systems and work with the built in serial port. Now these...

The RoBoard RM-G144 Magnetic Compass, ±16 3-Axis Accelerometer Board combines the HMC5843, a 3-axis magneto-resistive sensor with the ADXL345, a 3-axis accelerometer. The communication is done via I2C and the sensor connects easily to the RB-100 and RB-110 single board computers. The dimension of this sensor is only 20 x 20 mm. The I2C interface cable is included. The HMC5843 is a surface mount multi-chip module designed for low field magnetic sensing with a digital interface for applications...

RoBoard Interface Cable Set 2 Power cables 1 I2C Cable 1 RJ-45 connector cable for wired networking 1 2x5 cable for Com 6 Hi-Speed Serial 1 DB-9 serial connector cable 4 Comm breakout cables (4 pin) Additional Information, Datasheets, and Libraries

This dual axis robot joint is an advanced robotic joint kit using the MX-106T DYNAMIXEL from ROBOTIS. This Joint Kit is perfectly suited for a variety of robot applications, such as a humanoid robot ankle/hip joint or a Coxa joint in a quadrupedal or hexapod robot. *Pitch & Roll Degree of Freedom on same lateral axis *1400+ oz-in Torque Robotic Actuators *Ball Bearing Axis *Standardized Mounting Pattern *High Quality 5052/6061 Aircraft Aluminum Alloy Frame *Full Feedback Capabilities;...

This double MX-106T robot joint is an advanced robotic joint kit using a pair of linked MX-106T Dynamixel from Robotis. This Joint Kit outputs double the torque of the already massively powerful MX-106T servo. The MX-106T has a specific link cable (included) that pairs the servos so that they function as a single, ultra-powerful servo. It is perfectly suited for a variety of robot applications; various large scale humanoid robot joints, research level table-top robot arms, or any situation...

This 6 degree of freedom humanoid robot leg is an advanced robotic limb kit using the MX-106T DYNAMIXEL & MX-64T DYNAMIXEL from Robotis. This Humanoid Robot Leg provides a huge head start in building a high-end research level bipedal platform, utilizing top of the line robotic actuators from Robotis and a high quality machined aluminum skeletal frame. This leg kit does not come assembled. Epoxy will be required to assemble the feet and is not included. The kit does not come with a control or...

One of the most favored IR range sensors on the market. Detects distances from 4" to 30" (10cm-80cm). Note: The sensor sold here is actually a Sharp IR GP2Y0A21YK0F. It has the same distance range as a GP2D12 and very similar analog output properties. The GP2D12 is extremely difficult to source currently, so these sensors provide a great alternative. For more information on the minor differences, please refer to the datasheets for each sensor: Datasheets GP2D12 Datasheet GP2Y0A21YK0F...

These FSR's are perfect for robotic grippers, robot feet, and similar applications. We searched long and hard to find a flat force sensing resistor that we liked. When we tried these bad boys out for the first time we knew the search was over. Paper thin and well made, these FSR's are just plain fun to play with. FEATURE LIST Various sizes: .2", .5", 1.5", 24" strip Rubber backing Peel sticker backing Choice of male tabs or female connector Use voltage divider to adjust sensitivity band...

The DE-SWADJ 3 is an adjustable step down voltage regulator. The DE-SWADJ 3 is designed to be stronger, faster and better. It can process 3A of current, typical ripple is 25mV and under ideal circumstances the regulator can be up to 96% efficient. It continues the ease-of-use of the DE-SWADJ, making it simple to add an adjustable voltage source to a new or existing project with all the efficiency benefits of switch-mode power. The DE-SWADJ 3 is pin-compatible with the common 78XX family of...

100-Pound FlexiForce Force Sensor Measures from 0 to 100 lbs. FlexiForce Sensor Model A201.   FlexiForce is... A versatile, durable piezoresistive force sensor that can be made in a variety of shapes and sizes A piezoresistive sensing device in which resistance is inversely proportional to applied force A customizable, economical force measurement tool that is easily integrated into OEM products A patented, ultra-thin (0.008"), flexible printed circuit that senses contact force A...

Need a tiny servo for a tiny task? Try the FS90 Micro Plastic Gear Servo! This servo is great for scanning type sensors, tiny robots, and more! Each servo comes with a variety of horns. These servos use a standard PWM signal to control them. The Arduino does a great job of controlling PWM Servos, making it ideal for a variety of robotic projects. But sometimes powering these servos can be problematic. Powering servos from the Arduino's 5v regulator leads to underpowered servos, limited by both...

Description This 3-axis Accelerometer module is based on MMA7660FC with Digital Output I2C. This Grove can be used for sensing data changes, product orientation, and gesture detection through an interrupt pin (INT).It is a very low power, low profile capacitive MEMS sensor Grove. What is new Mounting edge for you to solder I2C Groves together, and free you from wiring. Flat bottom. 5VDC input Features Grove compatible interface 3 axis motion/orientation sensing Digital Output (I2C) 10,000 g...

Description 3-Axis Compass module, a member of Grove family uses I²C based Honeywell HMC5883L digital compass. This ASIC is equipped with high resolution HMC118X magneto-resistive sensors and a 12-bit ADC. It provides compass heading accuracy up to 1° to 2°. Signal conditioning like amplification, automatic degaussing strap drivers and offset cancellation are inbuilt. This Grove module also includes a MIC5205-3.3 for power supply requirement. Hence user can connect any 3.3V to 6V DC power...

Description Grove - 3-axis Gyro module based on ITG 3200. It is the world’s first single-chip, digital-output, 3-axis MEMS motion processing gyro optimized for gaming, 3D mice, and motion-based remote control applications for Internet connected Digital TVs and Set Top Boxes. The ITG-3200 features three 16-bit analog-to-digital converters (ADCs) for digitizing the gyro outputs, a user-selectable internal low-pass filter bandwidth, and a Fast-Mode I2C (400kHz) interface. Grove - 3-axis Gyro is...

Description The Electricity sensor module is a member of Grove. It is based on the TA12-200 current transformer which can change large alternating current into a small amplitude. You can use it to test large alternating current upto 5A. Features Grove compatible interface Maximum 5A input High accuracy Small size Applications Alternating current measurment Device condition monitoring Document Datasheet ...

Description This is a Grove interface compatible Magnetic switch module. It is based on encapsulated dry reed switch CT10. CT10 is single-pole, single throw (SPST) type, having normally open ruthenium contacts. The sensor is a double-ended type and may be actuated with an electromagnet, a permanent magnet or a combination of both. The magnetic switch is a wonder tool for designers who would like to turn a circuit on and off based on proximity. Features Grove compatible interface 2.0cm x 2.0cm...